• 제목/요약/키워드: Cut Joint

검색결과 150건 처리시간 0.027초

연속철근콘크리트 포장의 횡방향 철근 설계방법 및 시공관련 이슈 검토 (Construction Issues and Design Procedure for Transverse Steel in Continuously Reinforced Concrete Pavement (CRCP))

  • 최판길;원문철
    • 한국도로학회논문집
    • /
    • 제16권4호
    • /
    • pp.1-9
    • /
    • 2014
  • PURPOSES: The objective of this study is to evaluate construction issues and design for transverse steel in continuously reinforced concrete pavement(CRCP). METHODS : The first continuously reinforced concrete pavement(CRCP) design procedure appeared in the 1972 edition of the "AASHTO Interim Guide for Design of Pavement Structures", which was published in 1981 with Chapter 3 "Guide for the Design of Rigid Pavement" revised. A theory that was accepted at that time for the analysis of steel stress in concrete pavement, called subgrade drag theory(SGDT), was utilized for the design of reinforcement of CRCP - tie bar design and transverse steel design - in the aforementioned AASHTO Interim Guide. However SGDT has severe limitations due to simple assumptions made in the development of the theory. As a result, any design procedures for reinforcement utilizing SGDT may have intrinsic flaws and limitations. In this paper, CRCP design procedure for transverse steel was introduced and the limitations of assumptions for SGDT were evaluated based on various field testing. RESULTS: Various field tests were conducted to evaluate whether the assumptions of SGDT are reasonable or not. Test results show that 1) temperature variations exist along the concrete slab depth, 2) very little stress in transverse steel, and 3) warping and curling in concrete slab from the field test results. As a result, it is clearly revealed out that the assumptions of SGDT are not valid, and transverse steel and tie bar designs should be based on more reasonable theories. CONCLUSIONS : Since longitudinal joint is provided at 4.1-m spacing in Korea, as long as joint saw-cut is made in accordance with specification requirements, the probability of full-depth longitudinal cracking is extremely small. Hence, for transverse steel, the design should be based on the premise that its function is to keep the longitudinal steel at the correct locations. If longitudinal steel can be placed at the correct locations within tolerance limits, transverse steel is no longer needed.

The Importance and Multifunctions of Korean Paddy Fields

  • Cho Young-Son;Lee Byeong-Jin;Choe Zhin-Ryong
    • 한국작물학회지
    • /
    • 제51권2호
    • /
    • pp.179-185
    • /
    • 2006
  • The Ministry of Agriculture and Forestry announced in 2001 that the overall amount of paddy land set aside for rice will be cut down by 12% by 2005, decreasing from 1.08 million to 953,000 hectares. When evaluating the value of paddy rice systems, the multi-function of paddy systems in the monsoon climate is vital importance. The main functions of paddy rice systems are to conserve biodiversity and maintain sustainability. Some crucial environmental benefits of the paddy rice systems include: flood prevention, recharge of water resources, water purification, soil erosion and landslide prevention, soil purification, landscape preservation and air purification. The paddy rice systems in Korea, which are more diverse than upland crop systems, are known to be composed of 14 orders, 36 families and 134 species. The sustain ability of paddy rice production systems can never be overestimated. Rice is part of the culture and even the heart of spiritual life in the area under the monsoon climate. Therefore paddy rice systems should be preserved with the highest priority being the enhancement of the systems' multi-function. As an outlook to future research, the need of joint and interdisciplinary research projects between economists and natural scientists at inland as well as international levels were emphasized in establishing the development of counter-measure logic through actual proofed analysis.

CHARACTERISTICS OF ROLLED H SECTION STEEL WELDS JOINTED BY NEWLY DEVELOPED FLASH WELDING SYSTEM

  • Kim, You-Chul;Oku, Kentaro;Umekuni, Akira;Fujii, Mitsuru
    • 대한용접접합학회:학술대회논문집
    • /
    • 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
    • /
    • pp.826-830
    • /
    • 2002
  • In the civil engineering and architecture fields, welding for large sectional members, such as I section steel and H section steel, are usually performed. a flash welding system, by which large I section steel or H section steel can be welded for a short time, was newly developed. In order to know the basic characteristics of welded joints, the specimens were cut out from flash welded joints, and tensile and fatigue experiments were carried out. The joint efficiency of welded joints by flash welding is 100% for the specimens with reinforcements and 93% for without reinforcements. The fatigue strength of welded joints with reinforcement was about 50% of that of the base metal. Removing the reinforcement generated by flash welding, fatigue strength of flash welded joints became 75% of that of the base metal. In case of flash welded joints with reinforcements, after a couple of fatigue cracks had propagated, ductile fracture occurred at the toe. In flash welded joints without reinforcements, fracture occurred at the bond or at HAZ (Heat Affected Zone). In case of fracture at the bond, fracture was brittle, and in case at HAZ, fracture was ductile.

  • PDF

초음파타원진동절삭가공법에 의한 Co-Cr-Mo 합금의 경면가공 (Mirror Finishing of Co-Cr-Mo Alloy by Ultrasonic Elliptical Vibration Cutting Method)

  • 송영찬;전중건일;삼협준도
    • 한국정밀공학회지
    • /
    • 제25권3호
    • /
    • pp.56-62
    • /
    • 2008
  • The biocompatibility and the fatigue strength of Co-Cr-Mo alloy are excellent, so it is used well for the material of artificial joints. The head of artificial joint needs mirror surface for reduction of abrasive resistance. Mirror finishing of Co-Cr-Mo alloy with geometrically defined single crystal diamond cutting tools is handicapped by micro chipping of tool edge. In general, it is said that the micro chipping of diamond tool is caused by work hardening of Co-Cr-Mo alloy for the cut. In the present research, mirror finishing of Co-Cr-Mo alloy by applying ultrasonic elliptical vibration cutting was carried out. The experimental results show that the micro chipping of diamond tool was suppressed and the tool wear was remarkably reduced as compared with the ordinary diamond cutting without elliptical vibration motion. It was confirmed that the good mirror surface of maximum surface roughness of 25 nmP-V was obtained for the cutting length of about 14 m. It is expected that mirror finishing of Co-Cr-Mo alloy can be achieved by applying ultrasonic elliptical vibration cutting practically.

옻나무 경사핑거접합재의 휨강도와 AE 특성 (The Bending Strength and Acoustic Emissions Properties of Sloped Finger-Jointed Rhus Verniciflua)

  • 변희섭;김사익
    • 한국가구학회지
    • /
    • 제10권2호
    • /
    • pp.73-78
    • /
    • 1999
  • This paper describes the relationship between the bending strength properties of sloped finger-jointed woods and the acoustic emissions(AEs) generated during the test. Rhus verniciflua pieces were cut in sloped-finger types and glued with three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The AE cumulative event count and cumulative count were measured during the bending test. The results were as follows: The lower the bending strength(load) was, the generation time of AE event count got and the higher the increasing rate of AE event count became in the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl acetate oilic urethane resin adhesives. Therefore, the slope from load-AE cumulative event count was very steep. The patterns of AE event count and count were very similar. The relationship between the MOR and the AE parameter from load and AE cumulatve event count in the early stage of the sloped finger-jointed specimens bonded with polyvinyl acetate, polyvinyl-acryl and oilic urethane resin adhesives was much greater than that between the MOE and the MOR. Therefore, the AE signals obtained during bending test are useful for estimating the strength of sloped finger-jointed Rhus verniciflua specimens.

  • PDF

연속파 Nd:YAG 레이저를 이용한 Ni-MH전지용 저탄소강의 다층 박판 용접 특성 (Multi-thin plate welding characteristics of Low Carbon Steel for Ni-MH battery of using Continuous Wave Nd:YAG laser)

  • 양윤석;황찬연;유영태
    • 한국생산제조학회지
    • /
    • 제20권6호
    • /
    • pp.720-728
    • /
    • 2011
  • Lap joint welding conducts low carbon steel plates using a 2.0kW continuous wave Nd:YAG laser beam. The specimen is composed of thin plate of 20 sheets. Process Variables contain two controlled parameters of the laser power and the welding speed. In order to quantitatively examine the characteristics of the lap welding, the welding quality of the cut section, stain-stress behavior, and the hardness of the welded part are investigated. The weld width difference between the top and the bottom because the welding speed is increased. The reason, cooling rate is decreased because of fast welding speed. When the heat input is higher, larger volume of the base metal will melt and the welding heat has longer time to conduct into the bottom from the top. The microstructure and tensile properties of the joints are investigated in order to analyze the effects of heat input on the quality of laser welded specimen. From the results of the investigation, We observe that welding quality is good for the laser power of 1800W, and laser welding speed from 1.8m/min to 2.2m/min.

테일러드블랭크 용접을 위한 전단 공정 연구 (A Study on Mechanical Shearing Process for Tailored Blank Welding)

  • 유병길;이경돈
    • Journal of Welding and Joining
    • /
    • 제17권2호
    • /
    • pp.66-75
    • /
    • 1999
  • Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

  • PDF

울릉도 지형지 (A Geomorphology on the Ulleungdo)

  • 권동희
    • 한국지형학회지
    • /
    • 제19권4호
    • /
    • pp.39-57
    • /
    • 2012
  • 울릉도 화산체는 해수면 아래의 순상화산체와 해수면 위의 종상화산체로 크게 구분된다. 해수면 위 화산체의 지질은 기본적으로 알칼리 화산암류이며 이들은 다시 집괴암 및 응회암, 조면암 및 포놀라이트, 조면암질 부석, 조면안산암, 퇴적층 등 5개 지층으로 구분된다. 울릉도 지형은 전체적으로 화산지형이 우세하며 이들 화산지형이 풍화, 침식되어 다양한 풍화지형, 하천지형, 해안지형, 구조지형 등이 만들어졌다. 주요 화산지형으로는 칼데라분지, 중앙화구구, 주상절리 등이 있으며, 풍화지형으로는 타포니, 나마, 토르, 풍화동굴, 애추 등이 있다. 주요 해안지형으로는 해식애, 파식대, 시스택, 시아치, 해식동, 자갈해빈, 해안단구 등이 있다. 하천지형은 폭포를 제외하고는 그 발달이 미약하다.

절리 암반사면에서의 인자효과에 의한 유한요소 해석의 타당성 검토 (A Parametric Study for Jointed Rock Slope Using FEM)

  • 이진아;정창희;천병식
    • 한국지반공학회논문집
    • /
    • 제23권6호
    • /
    • pp.97-102
    • /
    • 2007
  • 토사사면의 안정성 해석에는 한계평형법이 널리 사용되고 있으나 절리가 발달한 암반사면의 파괴는 절리의 방향성과 파괴특성이 동시에 고려되어야 한다. 본 연구에서는 불연속면의 특성을 나타내는 인자와 암반사면의 형상 인자 등의 변화에 따른 결과를 분석하여, 범용 유한요소프로그램을 이용한 절리암반사면 안정해석의 타당성을 검증해 보고자 한다. 우선 흐름 법칙에 따른 차이를 비교하였으며, 인자효과 연구를 수행하였다. 독립변수로는 불연속면의 역학적 특성을 나타내는 절리면의 경사각과 점착력, 마찰각, 사면형상을 나타내는 암반사면의 경사와 높이 그리고 상재하중을 선택하였다. 그리고 종속변수로서 사면 아래에서 1/3 지점에서의 수평변위를 수치 해석하여 인자효과의 상대적인 크기를 비교해 보았다. 인자효과 연구를 통하여 각 인자에 대한 수평변위의 결과가 다양한 공학적 특성을 만족하여 절리암반사면의 안정해석에 응용이 가능함을 증명하였다. 암반사면의 설계 시 실제 지반조사와 실내실험 결과적용과 비선형성을 고려한 모델링이 가능하며, 강우와 같은 자연재해와 시공 중에 일어날 수 있는 응력변화 또한 표현할 수 있다. 또한, 유한요소해석을 통해 복잡한 암반구성조건과 지반 보강의 효과도 고려할 수 있으므로 절취경사, 보강 등에 대한 공학적인 결정시에 매우 유용할 것으로 사료된다.

인체 무릎관절 윤활포식세포 cluster designation 표지에 관한 면역전자현미경적 연구 (An Immune-Electron Microscopic Study for Cluster Designation on the Phagocytic Synovial Cells in the Knee Joint of the Human)

  • 임형수;조국형;김용욱;박경한;황영일;장가용;황덕호
    • Applied Microscopy
    • /
    • 제30권2호
    • /
    • pp.173-183
    • /
    • 2000
  • 사람 무릎관절 윤활막을 구성하는 윤활세포 중 윤활포식세포(phagocytic synovial cell, type A cell)의 기원에 대한 논의는 형태적으로 큰포식세포의 모습을 하고 있는 단핵포식체 계 (mononuclear phagocyte system)의 한 일부로서 아마도 골수(bone marrow)에서 기원되어졌을 것이라고 알려져 있다. 기능적으로도 LCA, HLA-DR과 Ia 항원에 양성반응을 보여 큰포식세포의 일부로 알려졌으나 아직 연구가 부족한 실정이다. 본 연구는 CD14와 활성화된 큰포식세포의 표지물로 알려진 CD105(endoglin)를 이용하여 윤활포식세포의 세포 내 발현부위를 규명하고, 기능적으로 활성화된 큰포식세포와 포식작용의 역할을 수행하는지 여부를 확인하기 위해 사람의 무릎관절에서 윤활세포들을 냉동초미세박절법을 이용한 면역조직화학 기법으로 CD14와 CB105에 대한 금표지를 하여 투과전자현미경으로 관찰한 결과 다음과 같은 결론을 얻었다. 1. CD14는 윤활포식세포의 과립세포질세망과 세포질및 가장자리, 공포 주변 부위에서 표지 되었으며 공포내에서는 표지 되지 많았다. 2. CD105(endoglin)는 윤활포식세포의 세포막 가장자리와 세포질 돌기를 따라 표지 되었으며 공포 주변 부위에서도 표지 되었으나, 공포 내에서는 표지 되지 많았다. 이상의 결과로 보아 사람 무릎관절 윤활세포층에 위치하는 윤활포식세포는 CD14와 CD105의 항원에 대한 표지를 보이므로 활성화된 큰포식세포나 포식작용의 역할을 수행하는 것으로 생각된다.

  • PDF