• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.509-514
• /
• 2004

This paper introduces the modified slip energy recovery system in order to improve its power factor and to reduce harmonics of line current waveforms. Twelve pulse line commutated converter with the chopper type IGBT is applied where the chopper is applied across the DC terminal and the chopped DC is fed to the converter operating as an inverter and then passed through the wye-wye and delta-wye transformer circuit. This scheme leads to be able to adjust the speed of the motor by the duty cycle of the chopper operating in PWM mode. The fuzzy logic controller is also introduced to the modified slip energy recovery system for keeping the motor speed to be constant when the load varies. The experimental results in testing the 0.22 kW wound rotor induction motor from no-load condition to rated condition show the effectiveness of the proposed control scheme.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.4
• /
• pp.415-421
• /
• 2014

In this paper, reactorless high efficiency boost DC/DC converter for EV is proposed. In proposed converter, improves efficiency because decrease power loss when the switches are turned on/off using zero current switching (ZCS) at all switch of primary full bridge. By replacing reactance ingredients of L-C resonance circuit for ZCS with leakage inductance ingredients of high frequency transformer, it reduces system size and expense because of not add special reactor. For validity verification of proposed converter, in the paper implements simulation using PSIM and perform experiment by making 5KW DC/DC converter. In experimental results, efficiency of proposed converter conformed superiority.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.43-48
• /
• 2016

Operational applications such as service restoration, voltage control and protection coordination are calculated based on the active and reactive power loading of the sections in the distribution networks. Loadings of the sections are estimated using the voltage and current measured from the automatic switches deployed along the primary feeders. But, due to the characteristics of the potential transformer attached to the switches, accuracy of the voltage magnitude is not acceptable to be used for section loading calculation. This paper proposes a new accurate section loading estimation method through voltage measurement error compensation by calculating voltage drop of the distribution line. In order to establish feasibility of the proposed method, various case studies based on Matlab simulation have been performed.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.255-256
• /
• 2016

This paper is presents a initial starting of SST with high voltage level source. Rush current flowing as difference between capacitor level and grid level can crush the whole system. Thus, industries have used initial constituted by resistance and relay. However the initial circuit used in industries can't apply high voltage application due to isolation and economic feasible problems. Therefore many countries study method can charge capacitor with another voltage sources. Also this paper introduce method charging primary side capacitor efficiently.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.139-140
• /
• 2016

이 논문에서는, 홀드-업 보상 기법을 통해 넓은 입력 범위에서 최적 설계가 가능한 비대칭 하프-브리지 컨버터를 제안한다. 제안된 회로가 갖는 주된 장점은 기존의 회로 동작에 어떠한 변화도 주지 않은 채, 넓은 입력 전압 범위에서도 최적 설계가 가능하게 하는 것이다. 기존의 비대칭 하프-브리지 컨버터는 입력 전압이 가장 낮은 홀드-업 시 설계가 되어, 정상 동작 시 비대칭 동작에 의한 단점을 갖는 반면, 제안 된 컨버터는 홀드-업 시 추가적인 전압 이득을 통해 출력 전압을 제어하기 때문에 홀드-업 동작 시 넓은 입력 전압 범위에 관계없이 컨버터의 최적 설계가 가능하다. 또한 기존의 방법들에 비해, 정상 동작 시에 추가 소자에 의한 손실이 발생하지 않아, 전 범위에서 고효율을 달성하였다. 250-410V 입력, 45V/3.3A 출력의 컨버터를 통해 제안 된 회로의 동작을 검증하였다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.185-188
• /
• 2002

In the design of superconducting power equipments such as transformer, cable and fault current limit, knowledge of the dielectric behavior of both liquid and gaseous at very low temperatures is very importance. Especially, Electrical properties of liquid nitrogen($LN_{2}$) and gaseous nitrogen($GN_{2}$) have become of great interest again since the discovery of high temperature superconductors. However, many sources of $LN_{2}$and $GN_{2}$ problems in the test of pancake coil model arising form the deficiency of insulation data. Therefore, this paper describes the results of an experimental study on the ac breakdown voltage($V_{B}$) properties of $LN_2$ and Air under the electrode of simulated HTS pancake coil. The ac breakdown voltage of $GN_{2}$ have been measured by pancake coil-pancake coil gaps over the temperature range of 293 K to 77 K.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.77-79
• /
• 2006

변압기에서 단락기계력에 대한 계산 분야는 수직력에 의한 Beam Bending, Tillting, 절연물 압축력과 수평력에 의한 Hoop, Compression 등이 있다. 본 논문은 전력용변압기 내부의 자계를 자기영상법을 이용하여 구하고 계산된 자계를 이용하여 단락 기계력을 구하는 방법을 제안하고자 한다. 또한 기존 FEM과 자기영상법과의 계산결과를 비교하였다.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.160-162
• /
• 1996

The estimation of AC losses is demanded for higher efficiency and stability in AC use of superconducting coils. Hysteresis loss occurred by a.c. transport current is called of self field loss, and it is major part of losses generated in a.c. superconducting wire in case of located in low external magnetic field as superconducting transformer with iron core, or in short twist pitch wire, multiply stacking cable. In this paper, we calculate self field loss of superconducting wire.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.486-488
• /
• 1996

A dc-dc converter which transfers l2-48W of power(regulated output voltage 24V) across a large, variable air gap(1-2cm) has been designed. This converter employs double resonance to compensate the large leakage inductance of the primary and secondary of the transcutaneous transformer. To maximize the effect of resonance, a constant frequency, duty cycle control method is used. The duty cycle control presents advantages over a frequency control in terms of increase in dc voltage gain and reduction of the primary current. The analysis and design procedure for the proposed scheme is presented and the performance result is simulated and verified experimentally.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.324-327
• /
• 1996

This paper presents the adoption of PWM converter to enhance input power factor in inverter arc welder. By using PWM converter in inverter arc welder, the disadvantages of bridge diode converter such as low input power factor is improved, new NCT(Noise Cut Transformer) is designed to reduce noise which has harmful effect in switching component, half bridge PWM inverter is adopted to reduce cost in inverter arc welder.