• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.398-401
• /
• 2011

This paper presents a high-efficiency CMOS PWM DC-DC buck converter. It generates a constant output voltage(1-2.8V), from an input voltage(3.4-3.9V). Inductor-based type is chosen and inductor current is controlled with PWM operation. The designed circuit consists of power switch, Pulse Width Generation, Buffer, Zero Current Sensing, Current Sensing Circuit, Clock & Ramp generation, V-I Converter, Soft Start, Compensator and Modulator. Switching Frequency is 1MHz, It operates in CCM when the load current is more than 40mA, and the maximum efficiency is 98.71% at 100mA. Output voltage ripple is 0.98mV(input voltage:3.5V, output voltage:2.5V). The performance of the designed circuit has been verified through extensive simulation using a CMOS $0.18{\mu}m$ technology.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.967_968
• /
• 2009

For lighting application, high-power LED nowadays is driven at 350mA and a sensing resistor is used to provide feedback for LED-current regulation. This method adds an IR drop at the output branch, and limits power efficiency as LED current is large and keeps increasing. In this paper, a power efficient LED-current sensing circuit is proposed. The circuit does not use any sensing resistor but extracts LED-current information from the output capacitor of the driver. Controlling the brightness of LEDs requires a driver that provides a constant, regulated current. In one case, the converter may need to step down the input voltage, and, in another, it may need to boost up the output voltage. These situations often arise in applications with wide-ranging ""dirty"" input power sources, such as automotive systems. And, the driver topology must be able to generate a large enough output voltage to forward bias the LEDs. So, to provide this requirements, 13W prototype Buck-Boost Converter is used.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.241-246
• /
• 2016

This paper presents a method that can improve the performance of permanent magnet synchronous motor current control by minimizing the measured current phase delay caused by the Low Pass Filter(LPF) used to cut off the noises that flowed in when feedback currents are measured. Although existing methods that change the Cutoff Frequency of the LPF can minimize phase delays during high speed rotations, their noise cutoff effects are much lower and this may lead to the decline of control performance. Therefore, in this study, an algorithm that can compensate current phase delays through relatively simple calculations from the synchronous motor d-q axis coordinate transformation matrix and the inverse transformation matrix is proposed and the validity of the proposed method is verified by comparing the waveform of the calculated current with the waveform of actual currents through simulations and experiments.

• Journal of dental hygiene science
• /
• v.24 no.2
• /
• pp.84-96
• /
• 2024

Background: Recent studies have elucidated the quorum-sensing mechanisms, biofilm formation, inter-pathogen interactions, and genes related to oral pathogens. This review aims to explore the recent expansion of drug targets against oral pathogens and summarize the current research on novel antibiotic substances derived from marine organisms that target oral pathogens. Methods: A comprehensive literature review summarized the novel mechanisms pertaining to quorum-sensing signal transmission systems, biofilm formation, and metabolite exchange in oral pathogens. The amino acid sequences of the 16 proteins identified as potential drug targets were systematically classified and compared across various oral microorganisms. Results: Through a literature review, we identified nine studies researching quorum sensing signaling inhibitors targeting oral pathogens. A comparison of the amino acid sequences of 16 potential drug targets in oral microorganisms revealed significant differences between oral pathogens and beneficial oral symbiotic microorganisms. These findings imply that it is possible to design drugs that can bind more selectively to oral pathogens. Conclusion: By summarizing the results of recent research on the signaling mechanisms that cause pathogenicity, new drug targets against oral pathogens were proposed. Additionally, the current status of developing new antibiotics for oral pathogens using recently developed quorum sensing inhibitors and natural products derived from marine organisms was introduced. Consequently, marine natural products can be used to develop drugs targeting new proteins in oral pathogens.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.11
• /
• pp.1-11
• /
• 1997

The transient current components of the dRAM are analyzed and the sensing current, data path operation current and DC leakage current are revealed to be the major curretn components. It is expected that the supply voltage of less than 1.5V with low VT MOS witll be used in multi-giga bit dRAM. A low voltage dual VT self-timed CMOS logic in which the subthreshold leakage current path is blocked by a large high-VT MOS is proposed. An active signal at each node of the nature speeds up the signal propagation and enables the synchronous DRAM to adopt a fast pipelining scheme. The sensing current can be reduced by adopting 8 bit prefetch scheme with 1.2V VDD. Although the total cycle time for the sequential 8 bit read is the same as that of the 3.3V conventional DRAM, the sensing current is loered to 0.7mA or less than 2.3% of the current of 3.3V conventional DRAM. 4 stage pipeline scheme is used to rduce the power consumption in the 4 giga bit DRAM data path of which length and RC delay amount to 3 cm and 23.3ns, respectively. A simple wave pipeline scheme is used in the data path where 4 sequential data pulses of 5 ns width are concurrently transferred. With the reduction of the supply voltage from 3.3V to 1.2V, the operation current is lowered from 22mA to 2.5mA while the operation speed is enhanced more than 4 times with 6 ns cycle time.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.321-329
• /
• 2000

Welding is essential for the manufacture of a range of engineering components which may vary from very large structures such as ships and bridges to very complex structures such as aircraft engines, or miniature components for microelectronic applications. Especially, a domestic situation of the welding automation is still depend on the arc sensing system in comparison to the vision sensing system. Specially, the gap-detecting of workpiece using conventional arc sensor is proposed in this study. As a same principle, a welding current varies with the size of a welding gap. This study introduce to the fuzzy membership filter to cancel a high frequency noise of welding current, and ART2 which has the competitive learning network classifies the signal patterns the filtered welding signal. A welding current possesses a specific pattern according to the existence or the size of a welding gap. These specific patterns result in different classification in comparison with an occasion for no welding gap. The patterns in each case of 1mm, 2mm, 3mm and no welding gap are identified by the artificial neural network.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.280-286
• /
• 1998

This paper proposes a novel method to reduce the torque ripple due to the non-ideality of the current sensing parts in vector-controlled inverter-fed AC motor drive systems. For PMSM(Permanent Magnet Synchronous Motor), motor output torque equations are derived in terms of their offset voltages and different voltage transducing gains. And the effects of phase current errors on motor torque are analyzed for both salient PMSM and non-salient PMSM. The proposed method can eliminate the torque ripple by nulling the offset voltages and setting the voltage transducing gains to the same value. To verify the proposed method, digital simulations are carried out for non-salient PMSM.

• Journal of Forest and Environmental Science
• /
• v.27 no.2
• /
• pp.73-79
• /
• 2011

The Barind tract is threatened by desertification and undergoing rapid change. In view of this fact it is very much essential to manage this barind tract under proper land-use plan. The present study evaluates the effectiveness of high-resolution satellite data and computer aided GIS techniques in assessing land-use change detection for the period 1990 to 2007 within the study area, which is very much essential to manage this barind tract under proper land-use plan, and for proper land-use plan it is necessary to get reliable information. The present study found five major land-use such as current fallow, current agriculture, settlement, irrigation water and water bodies. From the result, it is found that current fallow and water bodies decrease while settlement and current agriculture increase. Study concludes that as Barind tract is threatened by desertification, decrease of water bodies is not a good sign for the study area.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1788-1792
• /
• 2005

Eddy current sensor is representative instrument measuring gap to base metal and sensing trouble in base metal. The existing eddy current sensor works as measuring variance of sensor coil's inductance. But, sensor coil have phenomenon that not only inductance but also real resistance varies in real action. Conductivity and Permeability are main variable in sensor coil's varying impedance(inductance, real resistance). By searching relationship between conductivity-permeability and sensor coil's impedance, eddy current sensor gain advantage of elevation of accuracy, removal of alignment to each base metal, and continuous sensing to varying base metal.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1503-1506
• /
• 2008

A novel white-LED (light emitting diode) backlight system for 46"LCD TVs which involves the current controlled X-Y channel driving method is proposed in this paper. There are two problems related to the LED current in the conventional X-Y channel driving driven by a constant voltage source. To solve these problems, a real time current sensing system is applied to the conventional one and the time-division current sensing method is employed.