• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.439-446
• /
• 2018

The PHC pile has been increasingly used due to its implementation of the top-base method, which is advantageous in high penetration rate and bearing capacity reinforcement. Typically, when a PHC pile is manufactured, high-strength mixed materials are mainly used to enhance the compressive strength. However, recent studies have been conducted to utilize ground granulated blast-furnace slag (GGBS) in terms of economic efficiency. For this reason, this study manufactured PHC pile considering the replacement ratio and curing conditions of GGBS instead of high-strength mixed materials, and further investigated the engineering properties of the PHC pile. According to the experimental results, the compressive strength of GGBS-replaced PHC pile increased by steam curing, and particularly, PHC pile with 20% replacement of GGBS under $80^{\circ}C$ steam curing condition showed a compressive strength of approximately 84MPa. Furthermore, the experimental results confirmed that more hydration products were generated under the $80^{\circ}C$ steam curing condition than that under the $20^{\circ}C$ steam curing condition, which would affect the higher density of the PHC pile as well as the increase in the compressive strength.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.1 no.1
• /
• pp.9-19
• /
• 1981

Using superplasticizer or the methods of autoclave curing is the most typical and practical of the ways to make high strength concrete. In this study the high strength concrete piles by way of centrifugal forming and hand compacting, are put to the freezing and thawing test after the process of autoclave curing, water curing after steam curing, or stand water curing. And the relation of such piles to durability, the rate of strength decrease, and the rate of weight variation is shown. The durability of those test piles throughout freezing and thawing test proves to be comparatively sufficient in the above-mentioned curings when the piles contain a proper quantity of air. But it is also acknowledged that without A.E agent, the high strength concrete piles of autoclave curing is higher than those of the other curing in strength, but lower in modulus of dynamic elasticity and their durability factor after the test is much lower.

• Korean Journal of Plant Resources
• /
• v.25 no.4
• /
• pp.387-393
• /
• 2012

In order to improve storability of subtropical yam produced in South Korea, the major pathogens found during the storage were isolated and identified of the pathogenicity, and rot inhibition effect was studied based on the curing treatment condition. Penicillium sclerotigenum and Penicillium polonicum were identified as major pathogens causing rot in subtropical yam during storage, and P. sclerotigenum had stronger pathogenicity. Only the cut surface which has been made during a harvest and has been made smooth before curing generated a normal callus layer. The cut surface of tuberous root was cured in 95% of relativity humidity for three days at $23^{\circ}C$, and cured at $28^{\circ}C$ and $33^{\circ}C$. The observation of callus layer showed that the $23^{\circ}C$ treatment group had similar color saturation between tuberous root and pellicle, while the groups treated above $28^{\circ}C$ showed clear distinction. The generation rate of callus 0.5mm or bigger was 93 percent at $28^{\circ}C$ treatment, 96% at $33^{\circ}C$ treatment, but was 52% at $23^{\circ}C$ treatment. The conventional curing treatment group that used wind or sunlight at room temperature created little callus layer. The infection rate of pathogens according to the relative humidity inside the storage room was low at 40% and 60% of humidity, and the curing treatment period did not make a difference. When the humidity inside the storage room was 80%, all treatment groups rapidly increased the fungal pathogens. The rotten rate of each treatment was studied after 180 days during which the storage temperature was maintained at $16^{\circ}C$ and relative humidity 60%. While the rotten rate of tuberous root that has been cut in conventional curing treatment based on solar and wind was 43%, the one cured at over $28^{\circ}C$ and created the callus layer was less than 18%. While even a healthy tuberous root showed 25% of rotten rate in the traditional treatment group, the one cured at over $28^{\circ}C$ was less than 10%. The weight loss was 1-6% lower in the forced treatment group than in the conventional treatment group.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.2
• /
• pp.67-73
• /
• 2011

Ion exchange resins can be one of the good carriers for sustained drug release. However, the sustained release may not be enough only with themselves and hence film coating with rate controlling polymers can be applied to have a further effect on the drug release. Due to the environmental and economic issues of organic solvent for the polymer coating, aqueous polymeric systems were selected to develop dosage forms. Among the many aqueous polymeric dispersions for the film coating, EC (ethylcellulose) based polymers such as Aquacoat$^{(R)}$ ECD and Surelease$^{(R)}$ were evaluated.A fluid-bed coating was applied as a processing method. The drug release rate was quite dependent on the coating level so the release rate could be modified easily by changing different levels of the coating. The drug release rate in the Aquacoat$^{(R)}$ coated resin particles was strongly dependent on curing, which is a thermal treatment to make homogeneous films and circumvent drug release changes during storage. After dissolution test using the compressed tablets in which the coated resin particles are contained, inhomogeneous coating and even pores could be observed showing that the mechanical properties of EC were not resistant to granulation and compaction process. However, when tablets were prepared in different batches, the release profiles were almost identical showing the feasibility of the coated resin particle as incorporated into the tablet formulation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.1
• /
• pp.10-15
• /
• 1987

The experiment was designed to determine the proper shading rate and shading materials to decrease the excessive dried leaves during cure of burley tobacco. Five shading rates and seaven shading materials were applied on the pipe vinyl house from initial stage or yellow stage of cure. Temperature was lower and weight-loss of leaves delayed with shading from initial stage to browning stage of cure. Excessive dried leave were largely decreased as shading rate was increased to 70%. However, at shading rate more than 70%, its decreasing extent was fewer. Price per kg and physical properties improved considerably at shading rate of 50%. Shading materials alone could not completely prevent excessive dried leaves but it could decrease them. Orange, white and purple color vinyl among shading materials had so effects of shading as the black shading cloth during curing. However, white color vinyl didn't endure more than a few months due to sunshine. A difference of light quality in visible light was no significance on air curing.

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.1
• /
• pp.33-41
• /
• 2000

Fiber reinforced metal laminates(FRMLs) were new type of hybrid materials. FRMLs consist of high strength metals(Al 5052-H34) and laminated fiber with structural adhesive bond. The effect of resin mixture ratios on the fatigue crack propagation behavior and mechanical properties of aramid fiber reinforced aluminum composites was investigated. The epoxy, diglycidylether of bisphenol A(DGEBA), was cured with methylene dianiline(MDA) with or without an accelerator(K-54). Eight kinds of resin mixture ratio were used for the experiment ; five kinds of FRMLs(1)(mixture of epoxy and curing agent) and three kinds of FRMLs(2)mixture of epoxy, curing agent and accelerator). The characteristic of fatigue crack propagation behavior and mechanical properties FRMLs(2) shows more effecting than that of FRMLs(1).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.403-408
• /
• 2000

Hardened concrete contains pores of varying types and sizes, and therefore the transport of air through concrete can be considered. The rate of permeability will not only depend on the continuity of pores, but also on the moisture contents in concrete. In this paper, the effects of curing conditions and moisture content ratios on the carbonation and air permeability are investigated according to the accelerated carbonation test. The results are follows. 1) Compressive strength, carbonation velocity and air permeability are influenced by the moisture content and curing method. 2) The relationship between carbonation velocity coefficient and air permeability coefficient has been quite well established.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.273-276
• /
• 2003

The non-evaporable water and calcium hydroxides were measured by TG/DTA for studying the temperature effect on hydration of concrete mixture. The experimental parameters introduced in this study were the curing temperatures, ages and W/C ratios. The mixing temperature was also controlled to improve the efficiency of experimental work. While the mixture cured at high temperature showed the large quantity of non-evaporable water and calcium hydroxides at early age, the production rate of these hydration products was decreased as increasing the curing age, and the quantity of hydration product became smaller than that of the corresponding mixture cured at lower temperature at later age.

• Journal of the Korean Chemical Society
• /
• v.25 no.3
• /
• pp.140-144
• /
• 1981

The structure and reactivity of isophorone diisocyanate, which is used as a curing agent in propellants casting, were investigated using the EHT, CNDO/2 and STO-3G MO methods. The results showed that the reactivity can be assessed by the positive charge on C atom of -NCO group. The structure of this compound was found to be such that it has slow polymerization rate but provides homogenous matrix for explosives.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.227-230
• /
• 1998

The effects of post curing conditions on thermal properties of alumina filled epoxy resin system DGEBA/MDA/SN were investigated. As the post curing time increased at 15$0^{\circ}C$, the glass transition temperature increased from 121 to 124, slightly. As the heating rate increased, high thermal decomposing temperature (T$_{d}$) and most decomposing temperature (T$_{p}$) increased. For the case of post-cured system at 15$0^{\circ}C$ for 4 days showed lower values than virgin system. At the post curing condition the system must have been thermally degraded.ded.