• 한국정밀공학회지
• /
• 제20권2호
• /
• pp.76-84
• /
• 2003

Stereolithography is the technique using a laser beam to cure a liquid resin, a photopolymer, with three dimensional computer-aided design (CAD) data. The build parameters of stereolithography such as beam size, scan velocity. hatch spacing, layer thickness and etc. are determined by the accuracy of prototype, the build time and the cured properties of the resin. In particular, beam size is important processing parameter fur the other parameters. Therefore, this study observed the cured property to beam size. For this purpose, according to hatch spacing and beam size, the cure width and depth were measured on single cured line. Also, the cure width and depth were measured at single cured layer As a result of experiments. cure depth which varied from 0.23mm to 0.34mm was directly proportioned to beam radius. on the other hand, cure width which varied from 0.42mm to 1.07mm was inversely proportioned to beam radius. Surface roughness varied from 1.12 to 2.23 m for the ratio of hatch spacing to beam radius.

• Macromolecular Research
• /
• 제9권3호
• /
• pp.157-163
• /
• 2001

The influences of carbon black loading and cure type on the cure characteristics including kinetics and dynamic mechanical properties were investigated for a styrene-butadiene rubber (SBR). The rate constants of accelerated sulfur vulcanization reaction at three different temperatures were determined using a cure rheometer, and they were compared with those from the direct measurement of sulfur concentration. The strain softening behavior under dynamic deformation, known as the Payne effect was also discussed depending on the carbon black loading and cure type.

• Elastomers and Composites
• /
• 제53권3호
• /
• pp.168-174
• /
• 2018

Natural rubber (NR) and bromo-isobutylene-isoprene rubber (BIIR) were compounded with other formulation chemicals through polymer blending via a mechanical mixing method. After rubber vulcanization by hot-press compression molding, the cure characteristics, mechanical properties, and ozone resistance of the NR/BIIR blends were measured. As the BIIR content increased, the maximum torque of the blends decreased, while the optimum cure time and scorch time tended to increase. Furthermore, the hardness of the blends increased with increasing BIIR content, reaching the maximum value at 75 wt% BIIR, and decreased with a further increase in the BIIR loading. The tensile strength and elongation at break decreased with an increase in the BIIR content, reaching the minimum value at 75 wt% BIIR, and increased with a further increase in the BIIR content. In the ozone resistance test, cracks were not generated when the BIIR content was more than 75 wt%.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.797-803
• /
• 2001

The on-line cure monitoring of fiber reinforced thermosetting resin matrix composite material was performed for the better quality and productivity during manufacturing. Since the dissipation factor measured by dielectrometry method is dependent on the degree of cure and temperature of resin, in this study, a new method to obtain the degree of cure during on-line cure monitoring for glass/polyester composites was developed by employing a combination function of the temperature and the dissipation factor. Two sensor signals from a K-type thermocouple and an interdigitated dielectric sensor were processed during curing process under various cure cycles. The DSC (Differential Scanning Calorimetry) data was also used for the reference of degree of cure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1089-1092
• /
• 2001

In the stereolithography process, build parameters are laser power, scan velocity, scan width, bean diameter, layer thickness and so on. These values are determined according to product accuracy and build time. Build time can be reduced by improving of scan velocity, laser power, layer thickness, hatching space and so on. But variation of these parameters influence part accuracy, surface roughness, strength. This paper observed cure properties in various beam diameter. In order to examine these, relationships of scan velocity and cure depth, scan velocity and cure width according to various beam diameter in one scan line are measured. And cure thickness is measured according to beam diameter and scan velocity in scan surface of one layer. For reduction of build time, beam diameter and scan velocity is proposed in stereolithography process.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권4호
• /
• pp.50-55
• /
• 2007

Stereolithography (SLA) is a technique using a laser beam to cure a photopolymer liquid resin with three-dimensional computer-aided design (CAD) data, The accuracy of the prototype, the build time, and the cured properties of the resins are controlled by the SLA process parameters such as the size of the laser beam, scan velocity, hatch spacing, and layer thickness, In particular, the size of the laser beam is the most important parameter in SLA, This study investigated the curing properties of photopolymers as a function of the laser beam size, The cure width and depth were measured either on a single cure line or at a single cure layer for various hatch spacings and laser beam sizes, The cure depth ranged from 0.23 to 0.34 mm and was directly proportional to the beam radius, whereas the cure width ranged from 0.42 to 1.07 mm and was inversely proportional to the beam radius, The resulting surface roughness ranged from 1.12 to $2.23{\mu}m$ for a ratio of hatch spacing to beam radius in the range 0.5-2.0 at a beam radius of 0.17 mm and a scan velocity of 125 mm/sec.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.37-41
• /
• 2005

The curing of thermoset resin is accompanied with the changes in chemical and physical properties. The cure monitoring techniques can be designed by tracing these property changes. This paper presents the cure monitoring technique with fiber optic sensors to detect the change of refractive index during the polymerization process of engineering epoxy resin. The fiber optic sensor system was developed to measure the reflection coefficient at the interface between the fiber optic and the resin. The correlation between the sensor output and the degree of cure was performed following Lorentz-Lorenz law. The isothermal data from the sensors are compared with the data from differential scanning calorimeter.

• 대한한의학회지
• /
• 제18권2호
• /
• pp.148-154
• /
• 1997

In the pharmacology of traditional Korean medicine, each drug has its own specific characters. The different characters of drugs are employed to treat diseases, rectify the hyperactivity or hypoactivity of yin or yang, and help the body restore its normal physiological functions, consequently curing the diseases and restoring health. The various characters and functions of these drugs concerning medical treatment include drugs' properties, flavours, actions of lifting, lowering, floating and sinking, channel tropism, toxicity, etc. Among these theories, theory of properties and flavours of drugs provides the basis for drug analysis and application. 'Property' refers to the cold, hot, warm or cool nature of a drug. These properties of drugs are so sorted out according to the different actions of the drugs on the human body and thier therapeutic effects. Drugs which cure heat syndrome(yang syndrome) have a cold or cool property, whereas drugs which cure cold syndrome (yin syndrome) have hot or warm property Drugs of cold and cool-natured and drugs of warm and hot natures are of opposite properties. A cold-natured drug is different from a cool-natured on only in degree, and so is a warm-natured drug from a hot-natured drug. Most of the cool- or cold- natured drugs have the effects of clearing heat, purging fire, removing toxic substances, and nourishing yin, and are uese to cure heat syndromes. On the contrary, drugs of warm or hot nature usually have the effects of dispersing cold, warming up the interior, supporting yang, and treating collapse, and are therefore used to treat cold syndromes. We thought that the property of drug may be related to the autonomic nervous system in western medicine. In other words, drugs of warm or hot nature increase heart rate or acts like sympathomimetics, and drugs of cool or cold nature decrease heart rate or acts like para sympathomimetics . According to this hypothesis, we administrated some drugs to isolated rat right atrium in magnus tube. But there is no correlation between 'property' in traditional Korean medicine and autonomic nervous system in western medicine.

• 폴리머
• /
• 제25권1호
• /
• pp.63-70
• /
• 2001

대표적 가교형태 변화에 따른 유사한 stress-strain 특성을 나타내는 조건하에서 공정특성 및 전반적 물성에 미치는 영향을 조사하였다. 천연고무 기본 배합에서 촉진제나 황 공여체(sulfur donor) 증가에 따라 induction time은 길어지나, 가류속도는 빨라졌다. 가교계 변화에 따른 인장강도의 영향은 매우 적은 반면 신장율은 conventional vulcanization (CV)계에서 efficient vulcanization (EV)계로 갈수록 감소하는 경향을 보여 주었다. Blow-out이 발생하는 시간을 가교형태에 따라 비교하여 보면 CV

• Elastomers and Composites
• /
• 제33권4호
• /
• pp.281-289
• /
• 1998

4종류의 고무 즉, 천연고무(NR), styrene-butadiene copolymer(SBR), ethylene-propylene diene monomer(EPDM), brominated isobutylene-p-methyl-styrene copolymer(BIMS)의 영(Young) 탄성율을 비롯한 인장특성과 인열강도를 여러가지 가교도와 시험온도에서 측정하였다. 과가황(over-cure)의 영향을 조사하기 위해 과가교 고무컴파운드의 인장강도와 팽윤(swelling) 거동도 조사하였다. 모든 고무컴파운드에 대해 영 탄성율(E)은 가교도와 선형적인 비례관계를 보였다. EPDM이 가장 높은 기울기를 그리고 BIMS가 가장 낮은 기울기를 보였고, NR과 SBR은 이들 사이의 값을 나타내었다. 인열강도 Gc는 NR>BIMS>SBR>EPDM의 순으로 나타났다. 과가교에 따라 NR과 SBR의 가교도는 감소한 반면, BIMS는 오히려 증가하였고, EPDM은 거의 변하지 않았다.