• Journal of Environmental Science International
• /
• v.27 no.7
• /
• pp.543-554
• /
• 2018

From November 2013 to December 2016, ambient fine particulate matter ($PM_{2.5}$) was sampled in the downtown area of Jeju City, South Korea, which has seen rapid urbanization. The atmospheric concentrations of elements were measured in the $PM_{2.5}$ samples. This study focused on Cd, Cr, Cu, Mn, Ni, Pb, As, Sb, Sn, V, and Zn. The concentrations of Al, Na, K, Fe, Ca, Mg, Sr, and La were also obtained for reference. The objectives of this study were to examine the contributions of these elements to $PM_{2.5}$ concentrations in downtown Jeju City, and to investigate the inter-element relationships and the elemental sources by using enrichment factors and principal components analysis (PCA). A composition analysis showed that the 19 elements constituted 6.65 % of the $PM_{2.5}$ mass, and Na, K, Al, Fe, Ca, Mg, and Zn constituted 98 % of the total ion mass. Seasonal trend analysis for the sampling period indicated that the concentrations of the elements increased from November to April. However, no substantial seasonal variations were found in the concentrations of the elements. The composition ratios of some elements (Cu/Zn, Cu/Cd, Cu/Pb, V/Ni, and V/La) were found to be out of range when compared to the literature from other urban areas. The ratios between the elements and the PCA results showed that local contaminant sources in Jeju City rarely influence the composition of $PM_{2.5}$. This suggests that the major sources of $PM_{2.5}$ in Jeju City may include long-range transport of fine particulate matter produced in other areas.

• Fashion & Textile Research Journal
• /
• v.14 no.5
• /
• pp.866-877
• /
• 2012

The natural dyeing of hanji cotton fabrics with guava leaf extract was investigated. The temperature and time of dyeing were $40^{\circ}C$ and $90^{\circ}C$ for eighty minutes, respectively. In addition, the dyebath has been set at pH 5. Sn pre-mordanted fabrics showed the highest K/S value. Regardless of dyeing temperature, K/S values were high when Al, Cu, Fe-mordanted fabrics were dyed in post-mordanting and Sn-mordanted fabrics in pre-mordanting. The dyeing equilibrium was shown at the fourth time of repeated dyeing. In the processing of hanji cotton fabrics, K/S value was high when hanji cotton fabric was treated with soybean milk at $90^{\circ}C$. Similar K/S value of dyeing was shown when fabrics were processed with chitosan, regardless of dyeing temperature. High K/S value of dyeing was seen when fabrics processed with gallnut tannin at 40. Fabrics dyed with acidic water extract showed yellowish color. Fabrics dyed with alkaline water extract showed reddish color, and fabrics dyed with ethanol extract showed greenish yellow color. In case of Sn-mordanted fabrics, the washing fastness level was between 3 to 4, and other dyed fabrics showed low fastness. The dry cleaning fastness also showed very excellent result with level 4-5. The rubbing fastness of the fabrics was better in dry rubbing than in wet rubbing. For the light fastness, all dyed fabrics showed low fastness. For antibacterial activity, the dyed fabrics with guava leaf extract showed 99.9% of high antibacterial activity. Hanji cotton fabric maintained certain deodorization in the state of raw fabric. All dyed fabrics showed higher UV protection rate than control fabric.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.1-8
• /
• 2017

Two different fluorine-doped tin oxide (FTO)-coated glass substrates were investigated to find better suitability for CdTe solar cells. Substrate A consisted of FTO (300 nm)/$SiO_2$ (24 nm)/intrinsic $SnO_2$ (30 nm)/borosilicate glass (2.2 mm), and substrate B consisted of FTO (700 nm)/intrinsic $SnO_2$ (30nm)/borosilicate glass (1.8 mm). The overall thickness of the FTO/glass substrates was about 2.5 mm. The total light transmittance of substrate B was much higher than that of substrate A throughout the whole spectral region, even though the thickness of the FTO in substrate B was twice larger than that of the FTO in the substrate A. The short-circuit current greatly increased in substrate B and the external quantum efficiency (EQE) increased over the whole wavelength range. This study shows that the diffuse optical transmittance played a key role in the large EQE value in the blue wavelength region, and the direct transmittance played a key role in the large EQE value in the red wavelength region. The higher transmittance is due to the rough surface generated by the thicker FTO on glass. The conversion efficiency of the CdTe solar cell increased from 12.4 to 15.1% in combination of rough FTO substrate and Cu solution back contact.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.4
• /
• pp.1-9
• /
• 2011

Understanding the void characterization in the solder joints has become more important because of the application of lead free solder materials and its reliability in electronic packaging technology. According to the JEDEC 217 standard, it describes void types formed in the solder joints, and divides into some categories depending on the void position and formation cause. Based on the previous papers and the standards related to the void, reliability of the BGA solder joints is determined by the size of void, as well as the location of void inside the BGA solder ball. Prior to reflow soldering process, OSP(organic surface preservative) finished Cu electrode was exposed under $85^{\circ}C$/60%RH(relative humidity) for 168 h. Voids induced by the exposure of $85^{\circ}C$/60%RH became larger and bigger with increasing aging times. The void position has more influence on mechanical strength property than the amount of void growth does.

• Journal of the Korean Society of Costume
• /
• v.36
• /
• pp.109-119
• /
• 1998

For the purpose of standardization and practicability of natural dyeing, the mordanting and dyeing properties of Caseaslpinia Sappan, L. and Brazilin were studied. Appropriate extraction, dyeing and mordanting condition of Caeaslpinia Sappan, L. were determined, and the effect of mordanting method on dye up-take adn color fastness of dyed fabric was investigated. The most absorbance of Caeaslpinia Sappan, L. solution was 445nm, Brazilin was 448nm. The color of bazilin solution was affected by pH 7~9. The optimum temperature to extract Caesalpinia Sappan, L. was 10$0^{\circ}C$ adn dyeing solution for 1 hour. In case mordants concentration, the most absorbance was 0.3%. In case mordanting test, the best and proper temperature to quantities of absorbed mordants in silk was 8$0^{\circ}C$ and the most quantities of absorbed mordants in silk was mordant treatment by Cu. Effective dyeing time to silk was 60min. Effective mordanting temperature was 8$0^{\circ}C$, and its time was 30min. K/S value of dyeing fabrics was recoginazed by mordanting treat-ment, specially Fe, Sn, Al, Cu. K/S value of pre-mordanting was higher than post-mordanting. After soaping treatment K/S value of pre- and post-mordanting silk was decreased and 0.1%(W/V) quantity of mordant was sufficient for treatment. In the case of Caeaslpinia Sappan, L. fastness was increased by mordanting treatment. Mordants and mordanting treatment method affected the amount of absorption and color change of dyed silk.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.625-631
• /
• 2013

For the formation of solder bumps with a fine pitch of 130 ${\mu}m$ on a printed circuit board substrate, low-volume solder on pad (LVSoP) technology using a maskless method is developed for SAC305 solder with a high melting temperature of $220^{\circ}C$. The solder bump maker (SBM) paste and its process are quantitatively optimized to obtain a uniform solder bump height, which is almost equal to the height of the solder resist. For an understanding of chemorheological phenomena of SBM paste, differential scanning calorimetry, viscosity measurement, and physical flowing of SBM paste are precisely characterized and observed during LVSoP processing. The average height of the solder bumps and their maximum and minimum values are 14.7 ${\mu}m$, 18.3 ${\mu}m$, and 12.0 ${\mu}m$, respectively. It is expected that maskless LVSoP technology can be effectively used for a fine-pitch interconnection of a Cu pillar in the semiconductor packaging field.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.47-54
• /
• 2021

For the bonding of smaller PCB solder bumps of less than 100 microns, an experiment was performed to make up a tin plating solution and find plating conditions in order to produce a bump pattern through tin electroplating, replacing the previous PCB solder bumps process by microballs. After SR patterning, a Cu seed layer was formed, and then, through DFR patterning, a pattern in which Sn can be selectively plated only within the SR pattern was formed on the PCB substrate. The tin plating solution was made based on methanesulfonic acid, and hydroquinone was used as an antioxidant to prevent oxidation of divalent tin ions. Triton X-100 was used as a surfactant, and gelatin was used as a grain refiner. By measuring the electrochemical polarization curve, the characteristics of organic additives in Triton X-100 and gelatin were compared. It was confirmed that the addition of Triton X-100 suppressed hydrogen generation up to -1 V vs. NHE, whereas gelatin inhibited hydrogen generation up to -0.7 V vs. NHE. As the current density increased, there was a general tendency that the grain size became finer, and it was observed that it became finer when gelatin was added.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.4 no.1
• /
• pp.73-84
• /
• 2002

The purpose of this study was to investigate the natural dyeability on extract of Aloe Vera princeps. The experimental items were divided into the mordanting method, component of fabric, extracting portion, and kind of mordants. The experimental study was done to by laundering, abrasion(dry/wet), perspiration(acid/alkali), light fastness test and color difference by C.C.M system. The summerized finding resulted from experiments and investigation are suggested as follows: First, in the C.C.M test on mordanting method, color difference was significantly improved when mordants were treatmented. And the premordanting method showed the highest color difference. Second, in the C.C.M test on component of fabric, color difference of silk was higher than cotton. It was considered that silk has -$\NH_2$, -COOH, -OH more than cotton. Third, in the C.C.M Test on extracting portion, color difference of extracting in skin of Aloe leaf was three times higher than that of inside lump. Forth, in dyeing-fastness on mordants, laundering fastness showed 3 ~ 4 grade nearly. In perspiration-fastness(acid/alkali), Al(4~5/4~5) was the highest. In abrasion-fastness(dry/wet), cotton(4~5/4~5) was higher than silk (4~5/4) in all mordants. In light-fastness, silk(2~5) was higher than cotton(1~2) generally and especially Cu mordant of silk(4~5) was the highest. Sixth, in color difference analysis on 7 mordants Cu(29.9), Fe(28.7) and Cr(28.9) showed the highest in silk. And Cu(12.7), Fe(10.42) and Sn(10.43) showed the highest in cotton and Al(23.6, 8.0) showed the lowest in silk and cotton.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.9 no.1
• /
• pp.56-72
• /
• 1999

Airborne concentrations of welding fumes in which 13 different metals such as Al, Cd, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Si, Sn, Ti, and Zn were analyzed were measured at 18 factories including automobile assembly and manufactures, steel heavy industries and shipyards. Air samples were collected by personal sampler at each worker's worksite(n=339). Blood levels of Cd, Cu, Fe, Mn, Pb and Zn were also measured from samples taken from 447 welders by atomic absorption spectrometry and compared with control values obtained from 127 non-exposed workers. The results were as follows ; 1. Among various welding types, $CO_2$ welding 70.2 % were widely used, shielded metal arc welding(SMAW) 22.1 % came next, and rest of them were metal inert gas(MIG) welding, submerged arc welding(SAW), spot welding(SPOT) and tungsten inert gas(TIG) welding. 2. Welding fume concentration was $0.92mg/m^3$($0.02{\sim}15.33mg/m^3$) at automobile assembly and manufactures, $4.10mg/m^3$($0.02{\sim}70.75mg/m^3$) at steel heavy industries and $5.59mg/m^3$($0.30{\sim}91.16mg/m^3$) at shipyards, respectively, showing significant difference among industry types. Workers exposed to high concentration of welding fumes above Korean Permissible Exposure Limit(KPEL) amounted to 7.9 % and 12.5 %, in $CO_2$ welding and in SMAW at automobile assembly and manufactures and 62.7 % in $CO_2$ welding, and 12.5 % in SMAW at shipyards, and 66.2 % in $CO_2$ welding and 70.6 % in SMAW at steel heavy industries. 3. Geometric mean of airborne concentration of each metal released from welding fumes was below one 10th of KPEL in all welding types. Percentage of workers, however, exposed to airborne concentration of metals above KPEL amounted to 16.8 % in Mn and 7.6 % in Fe in $CO_2$ welding; 37.5 % in Cu in SAW, 30 % in Cu in TIG; and 25 % in Pb in SPOT welding. As a whole, 76 Workers(22.4%) were exposed to high concentration of any of the metals above KPEL. 4. There were differences in airborne concentration of metals such as Al, Cd, Cr, Cu. Fe. Mn, Mo, Ni, Pb, Si, Sn, Ti and Zn by industry types. These concentrations were higher in shipyards and steel heavy industries than in automobile assembly and manufactures. Workers exposed to higher concentration of Pb above KPEI amounted to 7.4 % of workers(7/94) in automobile assembly and manufactures. In shipyards, 19.2 % of workers(19/99) were over-exposed to Mn and 7.1 % (7/99) to Fe above KPEL. In steel heavy industries, 14.4 %(21/146), 7.5 %(11/146) and 13 %(19/146) were over-exposed to Mn, Fe and Cu, respectively. As a whole, 76 out of 339 workers(22.4%) were exposed to any of the metals above KPEL. 5. Blood levels of Cd, Cu, Fe, Mn, Pb, and Zn in welders were $0.11{\mu}g/100m{\ell}$, $0.84{\mu}g/m{\ell}$, $424.4{\mu}g/m{\ell}$, $1.26{\mu}g/100m{\ell}$, $5.01{\mu}g/100m{\ell}$ and $5.68{\mu}g/m{\ell}$, respectively, in contrast to $0.09{\mu}g/100m{\ell}$, $0.70{\mu}g/m{\ell}$, $477.2{\mu}g/m{\ell}$, $0.73{\mu}g/100m{\ell}$, $3.14{\mu}g/100m{\ell}$ and $6.15{\mu}g/m{\ell}$ in non-exposed control groups, showing significantly higher values in welders but Fe and Zn.

• Resources Recycling
• /
• v.10 no.5
• /
• pp.29-35
• /
• 2001

This study was carried out to recover gold, silver and valuable metals from the printed circuit boards (PCBs) of waste computers. PCBs samples were crushed under 1 mm by a shredder and separated into 30% conducting and loft nonconducting materials by an electrostatic separator. The conducting materials contained valuable metals which were then used as feed materials for magnetic separation. 42% of magnetic materials from the conducting materials was removed by magnetic separation as nonvaluable materials and the others, 58% of non magnetic materials, was used as leaching samples containing 0.227 mg/g Au and 0.697 mg/g Ag. Using the materials of leaching from magnetic separation, more than 95% of copper, iron, zinc, nickel and aluminium was dissolved in 2.0M sulfuric acid solution, added with 0.2M hydrogen peroxide at $85^{\circ}C$. Au and Ag were not extracted in this solution. On the other hand, more than 95% of gold and 100% of silver were leached by the selective leaching with a mixed solvent (0.2M($NH_4$)$_2$$S_2$$O_3$,0.02M $CuSO_4$,0.4M $NH_4$OH). Finally, the residues were reacted with a NaCl solution to leach Pb whereas sulfuric acid was used to leach Sn. Recoveries reached 95% and 98% in solution, respectively.