• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.2 no.1
• /
• pp.33-40
• /
• 1969

1. Physicochemical properties of sea water and soil of Korean tidal flats densely populated with species of Mactra veneriformis, Cyclina sinensis, Meretrix lusoria, and Tapes philippinarum, were investigated in order to find out the index of environmental factors in marine bivalve culture. 2. The turbidity varied with the change in concentrations of organic matter, silicate, and the exchangeable copper in sea water. All of these concentrations in Inchon, Kunsan, and Hansando were higher than those in Yusoo. In the 5 areas investigated the lowest were ditected at Kangnung. 3. The minerals and organic matter content in sea water dia not vary significantly among the different bivalve beds. And it was presumed that the soil texture was one of the most important environmental factors for the density of the bivalves in tidelands. 4. The soil texture index of the different bivalve beds was obtained as follow: 5. There were no significant differences of pH, the exchangeable calcium, and the exchangeable copper contents of bottom soils in the 4 different bivalve beds. As important factors in these areas, it seems that the amount of chemical properties might not affect the distribution of bivalve species. 6. Among the 4 beds the soil organic matter content was highest at the T. philippinarum bed and varied with the total nitrogen content. 7. Among the different bivalve beds, it was significant that the water holding capacity and available phosphorus content were highest at the M. veneriformis bed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.24-25
• /
• 2006

SmBCO coated conductors were successfully fabricated using EDDC (Evaporation using Drum in Dual Chambers) deposition system that is a bath type co-evaporation system for fabrication of superconducting tape and divided into two chambers named evaporation chamber and reaction chamber. To obtain long and high quality superconducting coated conductor, it is very important to secure the uniformity of all the deposition parameters m the deposition system such as deposition temperature, oxygen partial pressure, compositional ratios and so on. Therefore, we investigated the distribution of the parameters along the axis of the drum m EDDC on which tapes were wound helically. When the temperature on the middle point of deposition zone was $700^{\circ}C$, that on the edge of deposition zone was $675^{\circ}C$. When the thickness of SmBCO layer on the middle point of deposition zone was 1063 nm, that on the edge of deposition zone was 899 nm. The partial pressure of oxygen was 5 mTorr in the reaction chamber while that was $7{\times}10^{-5}$Torr in the evaporation chamber. The composition ratio of Sm:Ba:Cu, that was measured by EDX, was very uniform along the axis of the drum. Under these deposition conditions, critical current distribution along the drum axis was 175 A/cm, 190A/cm, 217.5 A/cm, 182.5 A/cm, 175 A/cm with the interval of 9 cm between samples. It means that the EDDC system has the potential of fabricating (100m, 200A) class coated conductor.