• 소성∙가공
• /
• 제14권6호
• /
• pp.502-508
• /
• 2005

Hypereutectic Al-Si alloys have been regarded attractive for automotive and aerospace application, due to high specific strength, good wear resistance, high thermal stability, low thermal expansion coefficient and good creep resistance. Spray casting of hypereutectic Al-Si alloy has been reported to provide distinct advantages over ingot metallurgy (IM) or rapid solidification/powder metallurgy (RS/PM) process in terms of microstructure refinement. In this study, hypereutectic Al-25Si-2.0Cu-1.0Mg alloy was prepared by OSPREY spray casting process. The change of strain rate sensitivity and Creep transition were analyzed by using the load relaxation test and constant creep test. High temperature deformation behavior of the hypereutectic Al-Si alloy has been investigated by applying the internal variable theory proposed by Chang et al. Especially, the creep resistance of spray casted hypereutectic Al-Si alloy can be enhanced considerably by the accumulation of prestrain.

• Journal of Mechanical Science and Technology
• /
• 제20권6호
• /
• pp.819-827
• /
• 2006

The stress-strain relation of aluminum (Al) alloy foam cell wall was evaluated by the instrumented sharp indentation method. The indentation in a few micron ranges was performed on the cell wall of Al-alloy foam having a composition or Al-3wt.%Si-2wt.%Cu-2wt.%Mg as well as its precursor (material prior to foaming). To extract the stress-stram relation in terms of yield stress ${\sigma}_y$, strain hardening exponent n and elastic modulus E, the closed-form dimensionless relationships between load-indentation depth curve and elasto-plastic property were used. The tensile properties of precursor material of Al-alloy foam were also measured independently by uni-axial tensile test. In order to verify the validity of the extracted stress-strain relation, it was compared with the results of tensile test and finite element (FE) analysis. A modified cubic-spherical lattice model was proposed to analyze the compressive behavior of the Al-alloy foam. The material parameters extracted by the instrumented nanoindentation method allowed the model to predict the compressive behavior of the Al-alloy foam accurately.

• 한국패류학회지
• /
• 제30권4호
• /
• pp.353-361
• /
• 2014

동합금이 사육 생물에게 미치는 생리적 영향을 조사하기 위해 화학적 조성이 다른 5종류의 금속판을 넣은 수조에서 사육한 북방전복을 대상으로 성패와 치패의 생존율, 호흡 및 배설률 그리고 기관별 중금속 축적률을 조사하였다. 생존율은 치패와 성패가 각각 27-60%와 63-83%로 성패가 더 높게 나타났다. 합금 조성에 따른 생존율의 뚜렷한 차이는 나타나지 않으나 중금속 축적률 그리고 영양적인 스트레스 등을 고려하면 동합금망은 전복 양성을 위한 가두리로서는 적합하지 못할 것으로 사료된다.

• 한국주조공학회지
• /
• 제23권1호
• /
• pp.30-39
• /
• 2003

Porous hybrid preforms were fabricated by reactive sintering using the compacts consisting of SiC particles, Fe and Al powders. Squeeze casting processing was employed to produce the composite in which the matrix phase is Al-Si7Mg. The microstructural change and wear resistance of the composites were investigated in terms of an amount of SiC particles. The wear loss was increased with increasing the contact pressure in the alloy containing SiC particles coated with Cu. The most drastic change was found to the specimen tested at 2.5 MPa of contact pressure. Concerning the alloys containing SiC particles coated with Ni-P, a drastic increase in the wear loss exhibited at 2 MPa of contact pressure in those alloys containing 4 and 8 wt. % of SiC particles coated with Ni-P. In the alloy containing 16 wt. % a proportional increase in wear loss was observed to the change of contact pressure. With respecting to the sliding velocity, the wear loss of the alloy containing SiC particles coated with Cu increased at the initial stage of wear process and then decreased. Similar result was found in the alloys containing SiC particles coated with Ni-P. On the basis of the present results obtained, it was found that wear resistance of the alloys tested was improved to show in the order of the alloy reinforced by coated SiC particles > by uncoated SiC particles > by intermetallic compound without SiC particles.

• 한국재료학회지
• /
• 제9권6호
• /
• pp.609-614
• /
• 1999

The effect of the amount of $SiO_2$dopant on the behavior of $AlO_2$$O_3$-composite formation by melt oxdation of Al-alloy was examined in this paper. The $SiO_2$powder was spread on the top surface of the Al-1Mg-3-Si-5Zn-1Cu alloy in th alumina crucible. The selected amount of each powder was 0.03, 0.10, 0.16g/$\textrm{cm}^2$. The oxidation behavior was determined by observing the weight gain after the heat treatment for 10 hours at 1373K. The macroscopic structure of formed oxide layer was examined by an optical microscope. The top surface and the cross-section of the grown oxide layer were investigated by SEM and analysed by EDX. The $SiO_2$ powder was determined to enhance oxidation by thermit reaction with Al which reduced the growth incubation period of the oxidation layer. As the amount of the $SiO_2$dopant increased, the growth rate decreased due to the precipitated Si which blocked the Al-alloy channel in the composite materials. However, more uniform layer was obtained due to the occurrance of the enhanced oxidation reaction in the whole alloy surface compared to the case of addition of less amount of dopant.

• 한국주조공학회지
• /
• 제19권6호
• /
• pp.456-465
• /
• 1999

The overall objective of this study is to investigate the effect of Ag addition on the mechanical properties and microstructure of rapid solidified 7000 Al series alloys. Al-Zn-Mg-Cu alloys with small amounts of Ag was fabricated into the powder by gas atomization. The powder was extruded after the cold compaction and degassing and then followed by T6 heat treatment. Microstructure observation, phase analysis, room and high temperature tensile test and hardness test were pursued. The tensile strength and hardness of Ag-added alloy after heat treatment was increased with increasing Ag contents. However, the elongation of extruded alloys was not increased as much as to be expected. The reason of this result seems to be related to $the{\Omega}$ phase, which contribute to the high temperature strength stability of Al-Cu-Zn alloys through the formation of eutectoid with Ag addition.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.93-104
• /
• 1996

This study evaluated relative hot cracking susceptibility of commercial aluminum alloy welds, and then suggested possible mechanisms operated in the weld fusion zone and in the heat affected zone based on the observed cracking morphologies, fractography and microstructural features. The fusion zone solidification cracking was found to be mainly due to a microsegregation of Cu, Si, and Mg in grain boundaries, while liquation cracking in the HAZ was by the incipient melting of the segregated grain boundaries and the consitutional liquation of large aging precipitates and intermetallic compounds in the partially melted zone adjacent to the fusion line which experienced a rapid thermal excursion during welding.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.155-156
• /
• 2015

최근 자동차 및 항공기의 경량화 관련하여 알루미늄 합금의 필요성이 높아지고 있으나, 자동차재료에 쓰이는 알리미늄 합금의 경우 높은 이온화 경향 때문에 Fe, Cu, Pb 등과 접촉하면 쉽게 부식되는 단점이 있다. 본 연구에서는 기존의 Magsimal-59 샘플과 본 연구에서 개발한 고용질, 저용질 Duplex 알루미늄 합금과의 내식성을 분극 및 갈바닉을 통해 확인하고, 균질화처리를 통해 내식성을 개선한다.

• 한국주조공학회지
• /
• 제3권1호
• /
• pp.13-21
• /
• 1983

In order to determine the feeding distance of aluminiun alloys (Alsi7Mg and AlCu4Ti) bar castings in the sand mold, the distance of the sound castings has been observed by radiograph for various risers, melt treatment, and casting design. Variation of porosity and hardness with the distance from the riser were also measured in order to determine the casting soundness. The results obained were as follows; 1) The modulus of riser should be 1.4 times of the casting`s 2) The maximum distance which can be made sound is greatly dependent on chemical composition and ingate location, and follows the rules given by the formula; a) When the melt flows into the casting first, and the riser afterward, D = 37.7 ${\sqrt{T}}$ for AlSi7Mg D = 31.2 ${\sqrt{T}}$ for pure aluminium D ${\ge}$ 54.8 ${\sqrt{T}}$ for AlCu4Ti Where T = casting thickness in mm Of this maximum distance, $aa{\sqrt{T}}$ for AlSi7Mg and 7.5 ${\sqrt{T}}$ for pure aluminium is made sound by the chilling effect of the casting edge. b) When the melt flows into the casting passing through the riser, $30{\times}30{\times}600mm$ bars can be made sound in all cases 3) Percentage of porosity is higer in AlCu4Ti than AlSi7Mg. And it is increased gradually by moving closer to the riser in case of $30{\times}30{\times}600mm$ bars, but for the $30{\times}30{\times}600mm$ bars it is increased gradually by moving closer to the center of bars. 4) Hardness variation is similar to the tendency of porosity. And it decreased gradually with approaching to the center in case of $30{\times}30{\times}600mm$ bars.

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.65-72
• /
• 2004

The tendency and degree of hot cracking of high strength 5083, 6N01 and 7N01 Al alloy welds by using DCSP-GTAW through modified Varestraint test and autogenous butt welding were investigated. In hot cracking test, 6N01 alloy showed the highest susceptibility to hot cracking in the weld metal and HAZ. Cracking susceptibilities generally increased with increase of solidification temperature range of the base metal and bead penetration-to-width ratio of the weld metal. The cracks in welds of the alloys vertically formed to solid-liquid interface and propagated along with columnar grain boundaries. The fracture facets of cracks showed the typical morphology of solidification crack observed as dendritic structures. Especially, in 6N01 alloy, liquation cracks which were due to elements of Si, Fe and Mg also observed in HAZ near fusion boundary. In butt welding of different Al alloys, the bead crack was mainly occurred in the welds of 6N01, 7N01 and other Al alloys together with 6N01 or 7N01. In the butt welds of 7N01, it was found that the component of Cu had an effect on the higher susceptibility to the hot cracking.