• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.91.2-91.2
• /
• 2010

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. The better performance of Ni/Cu contacts is attributed to the reduced series resistance due to better contact conductivity of Ni with Si and subsequent electroplating of Cu on Ni. The ability to pattern narrower grid lines for reduced light shading combined with the lower resistance of a metal silicide contact and improved conductivity of plated deposit. This improves the FF as the series resistance is deduced. This is very much required in the case of low concentrator solar cells in which the series resistance is one of the important and dominant parameter that affect the cell performance. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. This paper using selective emitter structure technique, fabricated Ni/Cu plating metallization cell with a cell efficiency of 17.19%.

• 한국전기전자재료학회논문지
• /
• 제26권3호
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.101-104
• /
• 2011

Many studies in crystalline silicon solar cell fabrication have been focused on high efficiency and low cost. In this paper, we carried out the doping procedure by varying the silicon wafer thicknesses and sheet resistance. The silicon wafers with various thicknesses were obtained by shiny etching and texturing. The thicknesses of wafers were 100, 120, 150, and $180{\mu}m$. The emitter layer formed by $POCl_3$ doping process had sheet resistance with 40 and $80{\Omega}/sq$ for selective emitter application. This experiment indicated wafer thickness did not influence sheet resistance but lifetime was strongly effected.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.235-235
• /
• 2010

The Anti-reflection coating(ARC) properties can be formed on silicon substrate using a simple electrochemical etching technique. This etching step can be improve solar cell efficiency for a solar cell manufacturing process. This paper is based on the removal of silicon atoms from the surface a layer of porous silicon(PSi). Porous silicon is form by anodization and can be obtained in an electrolyte with hydrofluoric. It have demonstrated the feasibility of a very efficient porous Si layer, prepared by a simple, cost effective, electrochemical etching method. We expect our research can results approaching to lower than 10% of reflectance by optimization of process parametaer.

• Transactions on Electrical and Electronic Materials
• /
• 제4권6호
• /
• pp.17-20
• /
• 2003

This paper describes the effect of halogenic gettering during oxide passivation of commercial solar cell with the $N^{+}$-P-$N^{+}$ structure. In order to study the effect of halogenic gettering on $N^{+}$-P-$N^{+}$ structure mono-crystalline silicon solar cell, we performed conventional POCl$_3$ diffusion for emitter formation and oxide passivation in the presence of HCl vapors. The $N^{+}$-P-$N^{+}$ structure based silicon solar cells were found to have higher short circuit current and minority carrier lifetime. Their performance was also found to be superior than the conventional $N^{+}$-P-$N^{+}$ structure based mono-crystalline silicon solar cell. The cell parameters of the $n^{+}$-p-$p^{+}$ and $n^{+}$-p-$n^{+}$ structure based cells, passivated by HCl assisted oxidation were measured. The improvement in $I_{sc}$ was attributed to the effect of the increased diffusion length of minority carriers, which came from the halogenic gettering effect during the growth of passivating oxide. The presence of chlorine caused gettering of the cells by removing the heavy metals, if any. The other advantage of the presence of chlorine was the removal of the diffusion induced (in oxygen environment) stacking faults and line defects from the surfaces of the silicon wafers. All these effects caused the improvement of the minority carrier lifetime, which in-turn helped to improve the quality of the solar cells.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.21-24
• /
• 2008

In this paper, we introduce the status of concentration photovoltaic system. Currently, crystalline silicon solar has 90% of total solar market. But in a few years, the concentration solar system is expected to be main one because cost increasement of silicon material is not stabilized unit now. At 2012, it will take 5% of the whole solar market. Less expensive, material requirement and high system efficiency give high driving force for intensive research on concentration system. It is time for us to initiate the basic study and evaluate the long term stability compared to crystalline silicon system. The detail discussion will be shown in the following paper.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.77-79
• /
• 2009

Amorphous/crystalline silicon heterojunction solar cells, TCO/a-Si:H (p)/c-Si(n)/a-Si:H(n)/Al, are investigated. The influence of various parameters for the front structures was studied. We used thin (10 nm) a-Si:H(p) layers of amorphous hydrogenated silicon are deposited on top of a thick ($500{\mu}m$) crystalline c-Si wafer. This work deals with the influence of the a-Si:H(p) doping concentration on the solar cell performance is studied.

• 한국전기전자재료학회논문지
• /
• 제26권10호
• /
• pp.754-759
• /
• 2013

Aluminum oxide($Al_2O_3$) film deposited by atomic layer deposition (ALD) is known to supply excellent surface passivation properties on crystalline Si surfaces. Since $Al_2O_3$ has fixed negative charge, it forms effective surface passivation by field effect passivation on the rear side in p-type silicon solar cell. However, $Al_2O_3$ layer formed by ALD process needs very long process time, which is not applicable in mass production of silicon solar cells. In this paper, plasma-assisted ALD(PA-ALD) was applied to form $Al_2O_3$ to reduce the process time. $Al_2O_3$ synthesized by ALD on c-Si (100) wafers contains a very thin interfacial $SiO_2$ layer, which was confirmed by FTIR and TEM. To improve passivation quality of $Al_2O_3$ layer, the deposition temperature was changed in range of $150{\sim}350^{\circ}C$, then the annealing temperature and time were varied. As a result, the silicon wafer with aluminum oxide film formed in $250^{\circ}C$, $400^{\circ}C$ and 10 min for the deposition temperature, the annealing temperature and time, respectively, showed the best lifetime of 1.6ms. We also observed blistering with nanometer size during firing of $Al_2O_3$ deposited on p-type silicon.

• 에너지공학
• /
• 제21권3호
• /
• pp.243-248
• /
• 2012

본 연구는 고온고습 시험을 통하여 Cell 레벨에서의 표면관찰 및 효율저하를 분석하였다. 고온고습 시험조건은 KS C IEC-61215에서 제시한 PV 모듈하의 조건을 이용하여 온도 $85^{\circ}C$, 습도 85%, 1000hr 동안 수행하였다. EL(Electroluminescence)촬영을 통하여 Cell 표면의 이상 유 무를 분석한 결과, 시간이 경과함에 따라, 부분적으로 표면이 손상되어 변색되는 것을 확인하였다. 고온고습 시험 전 단결정 Cell 및 다결정 Cell의 효율은 각각 17.7%, 15.5%였으며, 1000hr 수행 후 15.6%, 14.0%로 각각 11.9%와 9.3%의 감소율을 보였다. 또한, 경년 시 나타나는 전기적 특성을 분석하기 위하여 FF(Fill Factor)값을 분석한 결과, 고온고습 시험 후 단결정 Cell은 78.7%에서 75.0%로 4.7%, 다결정 Cell은 78.1%에서 76.7%로 1.8%의 감소율을 보였다. 태양전지 실리콘의 원자배열 및 순도에 따라 효율 변화에 영향을 받아 단결정 Cell이 다결정 Cell보다 효율저하가 크게 나타났다고 판단된다. 또한, FF감소율보다 효율 감소율이 크게 저하된 것을 확인할 수 있었으며, 이는 Cell의 외부환경적 요인에 의한 표면 손상이 p-n접합층 접촉저항과 경년 시 나타나는 FF 감소율보다 크게 영향을 준 것으로 판단된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.223-224
• /
• 2008

Important element are low cost, high-efficiency crystalline silicon solar cells. in this paper, Will be able to contribute in low cost, high-efficiency silicon solar cells, Applies oxide/nitride passivation, produced screen-printed solar cells. and the Measures efficiency, and evaluated a justice quality oxide/nitride passivation screen-printed solar cells.