• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.219-219
• /
• 2010

Silicides have been commonly used in the Si technology due to the compatibility with Si. Recently the silicide has been applied in solar cells [1] and nanoscale interconnects [2]. The modulation of Ni silicide phase is an important issue to satisfy the needs. The excellent electric-conductive nickel monosilicide (NiSi) nanowire has proven the low resistive nanoscale interconnects. Otherwise the Ni disilicide (NiSi2) provides a template to grow a crystalline Si film above it by the little lattice mismatch of 0.4% between Si and NiSi2. We present the formation of Ni silicide phases performed by the single deposition and the co-deposition methods. The co-deposition of Ni and Si provides a stable Ni silicide phase at a reduced processing temperature comparing to the single deposition method. It also discusses the Schottky contact formation between the Ni silicide and the grown crystalline Si film for the solar cell application.

• Journal of the Korean institute of surface engineering
• /
• 제40권3호
• /
• pp.138-143
• /
• 2007

The effects of texturing and anti-reflection coating on the reflection properties of multi-crystalline silicon solar cell have been investigated. The chemical solutions of alkaline and acidic etching solutions were used for texturing at the surface of multi-crystalline Si wafer. Experiments were performed with various temperature and time conditions in order to determine the optimized etching condition. Alkaline etching solution was found inadequate to the texturing of multi-crystalline Si due to its high reflectance of about 25%. The reflectance of Si wafer texturing with acidic etching solution showed a very low reflectance about 10%, which was attributed to the formation of homogeneous. Also, deposition of ITO anti-reflection coating reduced the reflectance of multi-crystalline si etched with acidic solution($HF+HNO_3$) to 2.6%.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.2060-2060
• /
• 2011

This paper was investigated the frequency property for optimal operating conditions of mono-crystalline Si solar cell. An internal impedance of mono-crystalline Si solar cell was influenced frequency. An optimal operating conditions of solar cell was under about 10[kHz].

• Korean Journal of Materials Research
• /
• 제9권1호
• /
• pp.99-103
• /
• 1999

We investigated the crystalline behavior in active ion implanted silicon through Raman spectroscopy. Four a-Si(amorphous Si) peaks were observed that are related to the ion implantation induced a-Si layer. After the isochronical anneal(30min). and isothermal anneal($450^{\circ}C$), noticeable recovery of crystalline-Si peak at 519cm\ulcorner and peak center shift of the a-Si TO from 465cm\ulcorner to 480cm\ulcorner were observed by RNM(Random Network Model). By applying RNM and SCLM(Spatial Correlation Length Model), the peak center and FWHM(the Full Width at half Maximum) of a-Si were changed dramatically between T\ulcorner=$200^{\circ}C$ and 30$0^{\circ}C$. From the results, it can be said that there is an abrupt structural change at this temperature region.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.178-178
• /
• 1999

Low temperature Si epitaxy can provide flexibility for a device designer to tailor or optimize the device performance. It is better method for controlling the doping thickness, concentration and profile than ion implantation and diffusion. But there is a limited growth thickness in this method. At a given temperature, the film grows epitaxially for a certain limiting thickness(hepi) and becomes amorphous. The transition from crystalline Si to amorphous Si is abrupt. In this study, Si film was deposited by ion beam sputter deposition on Si (0001) above a limiting thickness and measure the strain in the interface between crystalline Si and amorphous Si. The strain was compressive and the maximum value was about 2%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.299.2-299.2
• /
• 2013

We investigated the potassium remaining on a crystalline silicon solar cell after potassium hydroxide (KOH) etching and its effect on the lifetime of the solar cell. KOH etching is generally used to remove the saw damage caused by cutting a Si ingot; it can also be used to etch the rear side of a textured crystalline silicon solar cell before atomic layer-deposited Al2O3 growth. However, the potassium remaining after KOH etching is known to be detrimental to the efficiency of Si solar cells. In this study, we etched a crystalline silicon solar cell in three ways in order to determine the effect of the potassium remnant on the efficiency of Si solar cells. After KOH etching, KOH and tetramethylammonium hydroxide (TMAH) were used to etch the rear side of a crystalline silicon solar cell. To passivate the rear side, an Al2O3 layer was deposited by atomic layer deposition (ALD). After ALD Al2O3 growth on the KOH-etched Si surface, we measured the lifetime of the solar cell by quasi steady-state photoconductance (QSSPC, Sinton WCT-120) to analyze how effectively the Al2O3 layer passivated the interface of the Al2O3 layer and the Si surface. Secondary ion mass spectroscopy (SIMS) was also used to measure how much potassium remained on the surface of the Si wafer and at the interface of the Al2O3 layer and the Si surface after KOH etching and wet cleaning.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.52-52
• /
• 2011

A novel deposition process for n-type nanocrystalline silicon (n-type nc-Si) thin films at room temperature has been developed by adopting the neutral beam assisted chemical vapor deposition (NBa-CVD). During formation of n-type nc-Si thin film by the NBa-CVD process with silicon reflector electrode at room temperature, the energetic particles could induce enhance doping efficiency and crystalline phase in polymorphous-Si thin films without additional heating on substrate; The dark conductivity and substrate temperature of P-doped polymorphous~nano crystalline silicon thin films increased with increasing the reflector bias. The NB energy heating substrate(but lower than $80^{\circ}C$ and increase doping efficiency. This low temperature processed doped nano-crystalline can address key problem in applications from flexible display backplane thin film transistor to flexible solar cell.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.560-560
• /
• 2006

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.72.2-72.2
• /
• 2010

Nowadays, the crystalline Si Solar cell are expected for economical renewable energy source. The cost of the crystalline Si solar cell are decreasing by improvement of its efficiency and decrease of the cost of the raw Si wafers for Solar cells. This Si wafer based crystalline Si solar cell is the verified technology from several decade of its history. Now, I will introduce one method that can be upgrade the efficiency by using simple and economical method. The name of this method is Rear Side Etching(RSE). The purpose of rear side etching is the elimination of n+ layer of rear side and increase of the flatness. The effects of rear side etching are the improvement of Voc and increase of efficiency by reducement series resistance and forming of uniform BSF. The experimental procedure for rear side etching is very simple. After anti-reflection coating on solar cell wafer, Solar cell wafer is etched by the etching chemical that react with only rear side not front side. This special chemical is no harmful to anti-reflection coating layer. It can only etched rear side of solar cell wafer. We can use etching image by optical microscope, minority carrier life time by WCT 120, SiNx thickness and refractive index by ellipsometer, cell efficiency for the RSE effect measurement. The key point of rear side etching is development of etching process condition that react with only rear side. If we can control this factor, we can achieve increase of solar cell efficiency very economically without new device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제15권3호
• /
• pp.281-286
• /
• 2002

In odder to investigate the magnetic properties of CoCr-based bilayered thin films on kind of underlayer, we introduced amorphous Si layer to Co-Cr(-Ta) magnetic layer as underlayer. First, we prepared CoCr and CoCrTa single layer using the Facing Targets Sputtering system to investigate theirs properties. It was revealed that with increasing the film thickness of CoCr, CoCrTa single layer, crystalline orientation and perpendicular coercivity was improved. The CoCrTa thin film showed bettor crystalline and magnetic characteristics than CoCr thin film. As a result of investigating magnetic properties of CoCr and CoCrTa magnetic layer on introducing the Si underlayer, perpendicular coercivity and saturation magnetization of CoCr/Si and CoCrTa/Si bilayered thin film were decreased due to the increased grain size and diffusion of Si atoms to magnetic layer. And they showed constant with increasing the film thickness of Si thin film. However, in case of CoCrTa/Si bilayered thin film, in-plane coercivity was controlled low at about 250Oe. The c-axis orientations of CoCr/si and CoCrTa/Si bilayered thin film showed a good crystalline characteristics as about $2^{\circ}$.