• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3719-3725
• /
• 2012

최근, 건설공사의 급증으로 인한 양질의 하천모래의 고갈로, 콘크리트용 대체골재로서 바다모래, 부순모래 및 순환잔골재 등의 사용이 증가하고 있다. 그러나, 미세척 바다모래는 함유된 염화물로 인하여 철근콘크리트 구조물에 사용할 경우, 철근부식 유발로 구조물의 내구성에 악영향을 미치고, 부순모래는 미립분이 많고 입도조정이 어려워서 철근콘크리트 구조물에 널리 사용되지 못하고 있는 실정이다. 한편, 낙동강 세사는 낙동강 중 하류에 대규모로 분포하고 있고, 입도를 제외하면 콘크리트용 잔골재로서 품질이 우수하므로 이에 관한 연구가 시급히 요구되고 있다. 따라서 본 연구의 목적은 콘크리트 잔골재로서 낙동강 세사를 적극적으로 활용하기 위하여 그것의 물성을 평가하는 것이다. 이를 위하여 낙동강 본류 대표위치별로 시료를 채취하여 이들의 절건밀도, 입도, 단위용적질량 등의 물성을 평가하였는데, 그 결과 낙동강 세사는 입도를 제외하면 잔골재로서의 물성이 우수한 것으로 나타났다.

• International Journal of Concrete Structures and Materials
• /
• 제3권1호
• /
• pp.3-9
• /
• 2009

This paper examines the incorporation of the crushed sand (CS) and desert sand (DS) in the formation of self compacting concrete (SCC). These sands have been substituted for the rolled sand (RS), which is currently the only sand used in concretes and which is likely to run out in our country. DS, which comes from the Tunisian Sahara in the south, is characterized by a tight distribution of grains size. CS, a by-product of careers containing a significant amount of fines up to 15%, is characterized by a spread out granulometry having a maximum diameter of around 5mm. These two sands are considered as aggregates for the SCC. This first part of the study consists in analyzing the influence of the type of sand on the parameters of composition of the SCC. These sands consist of several combinations of 3 sands (DS, CS and RS). The method of formulation of the adopted SCC is based on the filling of the granular void by the paste. The CS substitution to the RS made it possible, for all the proportions, to decrease the granular voids, to increase the compactness of the mixture and to decrease the water and adding fillers proportioning. These results were also obtained for a moderate substitution of DS/CS (< 40%) and a weak ratio of DS/RS (20%). For higher proportions, the addition of DS to CS or RS did not improve the physical characteristics of the SCC granular mixture.

• 한국건축시공학회지
• /
• 제8권4호
• /
• pp.87-93
• /
• 2008

With an increased use of alternative aggregate due to exhaustion of quality aggregate resources, the amount of used crushed aggregates have been increased and as a result, development of admixture materials has also been improved and its amount of use is increasing from day to day in order to secure quality in concrete. Accordingly, the purpose of this study is to make concrete of good quality by using chemical admixture developed in this study by replacement rate of fine aggregate. At first, susceptibility, compressive strength ratio and length change ratio in both fresh and hardened concrete were evaluated according to corresponding regulation. As for high performance related regulation, APC NO.3 and PC series were going to rule, and as for AE agent regulation, replacement ratio of fine aggregate of high performance chemical admixture was 10:0 and other chemical admixture met quality regulation for AE agent.

• 한국해양공학회지
• /
• 제18권1호
• /
• pp.53-62
• /
• 2004

The Purpose of this study is to recycle the waste concrete, which is generated in huge quantities, from construction works. in order to achieve this goal, it is important to determine the compressive strength, workability, slump, and ultrasonic velocity of recycled aggregate concrete. Thus, several experiment parameters are considered, such as water-cement ratios, sand percentage, and fine aggregate composition ratios, in order to apply the recycled aggregate concrete to pre-cast artificial fishing reefs. From the results, it has been shown that the proper mix designs for reef concrete are W/C=45%, S/a=50%, SR50:SN50 in recycled sand and natural sand mix combination case, W/C=45%, S/a=50%, SC50:SN50 in crushed sand and natural sand mix combination case, W/C=45%, S/a=50%, SR50:SC50 in recycled sand and crushd sand mix combination case. Also, this study shows that the shape and surface roughness of fine aggregate particles have an effect on the strength, slump, ultrasonic velocity of tested concrete, and the compressive strength ratios of 7days' and 90days' curing ages of recycled aggregate concrete are about 70% and 110% of 28days' curing age.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.271-275
• /
• 1998

Recently, in the trend of using aggregate, it is common that coarse aggregate is replaced with crushed stone and fine aggregate is replaced with sea sand as a replacing aggregate. In this study, to judge the adaptability of using antiwashout underwater concrete, we used mixed sand (river sand : sea sand= 5 : 5) and changed W/C. After carrying out the research on the strength development of the compressive strength of specimen, tensile strength, fluxural strength which is produced and cured in the air and salt water, we founded that when W/C was low and the amount of AWA and SP were increased, the state of strength development was excellent.

• 한국건축시공학회지
• /
• 제17권1호
• /
• pp.111-117
• /
• 2017

Stone powder sludge is a byproduct of the crushed aggregate industry, and most of it is dumped with soil in landfills. The disposal of stone powder sludge presents a major environmental problem. This paper investigates the effects of stone powder sludge on the fluidity, density, strength and micro-structure properties of AAC(autoclaved aerated concrete) samples. Stone powder sludge was obtained from a crushed aggregate factory in order to investigate its applicability as a substitute for quartz sand in AAC. To determine the properties of the AAC samples produced with stone powder sludge, specimens containing different foam ratios were produced. Flow value, density, compressive strength, tensile strength and flexural strength of the samples were tested, and X-ray diffraction (XRD) was performed. The test results indicated that the compressive strength of AAC specimens (F120) with stone powder sludge was higher than that of AAC specimens (Q120) with quartz sand for same foam ratio of 120%. For all XRD diagrams, a higher number of tobermorite peaks was shown for the F120 sample than for the Q120 sample, which may explain the slightly higher strength gain in the F120 sample.

• 한국산업융합학회 논문집
• /
• 제8권3호
• /
• pp.169-176
• /
• 2005

The purpose of this study is to develop the high strength crushed sand concrete in conditions of water binder ratios of 25, 30, 35% and blast-furnace slag substitutions of 0, 15, 30, 45%. Additionally, in case of water binder ratio of 30%, the maximum size of coarse aggregate is two kinds of 13, 19 mm. The conclusions of this study are as follows ; 1. The compressive strength appeared lower in early age as compared with that of plain concrete according to increasing of the blast-furnace slag substitution. But, the compressive strength was respectively 5, 6, 10% larger than that of plain concrete in case of 25, 30, 35% water binder ratios, 28 days, 30% blast-furnace slag substitution and 19mm coarse aggregate. 2. According to increasing of the blast-furnace slag substitution, the modulus of elasticity and the tensile strength of concrete increased. 3. The length change by the shrinkage increased when the larger coarse aggregate was used, and decreased according to higher blast-furnace slag substitution.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.308-315
• /
• 1996

The utilization of high flowing concrete in construction sites is a world wide trend, and it will be increase to need for high flowing concrete in our construction sites. While it is quite easy to make high-flowing concrete in the laboratory, controlling slump in the field long enough to ensure easy placement once the concrete arrives at job site can be difficult. This study is the experimental study on the high-flowing and engineering properties of high flowing concrete using river sand and crushed stone according to the replacement percentage of fly-ash. As a results of this study is the mix proportion of replacement percentage of fly-ash 30% better than the others. And it is confirm to possibility of manufacture of the high flowing concrete.

• International Journal of Concrete Structures and Materials
• /
• 제4권2호
• /
• pp.105-108
• /
• 2010

In order to determine the effect of the use of limestone sand on chloride ion ingress in mortar, specimens were cast with two different sands: siliceous sand (used as reference) and limestone crushed sand (used for this study). To compare and assess the resistance of this mortar to chloride penetration, two different diffusions tests were employed: slow migration and rapid migration (AASHTO test). In this study, calculation of the effective diffusion coefficient is proposed using a model based on Nernst. Planck equation. The diffusion coefficients from each sample were compared. The results for all tests show that the diffusion coefficients for siliceous sand mortar are larger than those obtained with limestone sand. It appears also that the diffusion coefficient varies as a function of the W/C ratio.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.85-88
• /
• 2006

This study investigated influence of fine aggregate types on fundamental properties of cement mortar. Test showed that concrete using lime stone crushed fine aggregate(L) exhibited the most favorable fluidity due to grain shape and particle distribution, and next was blending aggregate miting L and G, blending aggregate mixing L and N, granite crushed fine aggregate(G), natural fine aggregate(N) in an order. Concrete using N had the highest air content and L was the smallest value because of the effective filling performance by continuos particle distribution. Compressive, tensile and flexural strength of all concrete using L had the highest value due to the smallest value of air content. It is also found that concrete using L resulted in decrease of drying shrinkage length change ratio.