• Biotechnology and Bioprocess Engineering:BBE
• /
• v.2 no.2
• /
• pp.90-93
• /
• 1997

Recombinant exoinulinase was partially purified form the culture supernatant of S.cerevisiae by(NH4)2SO4 precipitation and PEG treatment. The purfied inulinase was immobilized onto Amino-cellulofine with glutaraldeyde as a cross-linking agent. Immobilization yield based on the enzyme activity was about 15%. Optimal pH and temperature of immobilized enzyme were found to be 5.0 and 6$0^{\circ}C$, respectively. The enzyme activity was stably maintained in the pH ranges of 4.5 to 6.0 at 6$0^{\circ}C$. 100% of enzyme activity was observed even after incubation for 24 hr at 6$0^{\circ}C$. In the operation of a packed-bed reactor containing 412U inulinase, dahalia inulin of 7.5%(w/w) concentration was completely hydrolyzed at flow rate of 2.0mL/min at 6$0^{\circ}C$, resulting in a volumetric productivity of 693 g-reducing sugars/L/h. Under the reaction conditions of 1.0mL/min flow rate with 2.5% inulin at 6$0^{\circ}C$, the reactor was successfully operated over 30 days without loss ofinulinase activity.

• Journal of the Korean Chemical Society
• /
• v.62 no.2
• /
• pp.93-98
• /
• 2018

Bis-GMA, TEGDMA, and camphorquinone were used as the main material, cross-linking agent, and photoinitiator, respectively. In addition, 2-isocyanatoethyl methacrylate was used as an additive for high strength, while the 3-hydroxypyridine was used as an additive for antibacterial activity. Photopolymerization was also carried out at a 440-480 nm wavelength and at about $1000mW/cm^2$ intensity for about 40 seconds. The breaking strength measurement of the samples showed that the breaking strength increased along with increasing the addition ratio of IEM, while it took less time until the polymerization was complete, thereby suggesting that the degree of polymerization has the tendency to increase. And also, compared to the size of the clear zone formed by ampicillin, the 3-hydroxypyridine group exhibited antimicrobial activity induced by ampicillin. The results of this study suggest that the use of 2-isocyanatoethyl methacrylate as an additive for high strength and 3-hydroxypyridine as an additive for improved antibacterial activity would improve the usability of the fabricated polymer as a dental resin cement material with high functionality.

• Environmental Engineering Research
• /
• v.11 no.4
• /
• pp.208-216
• /
• 2006

In order to create a single flocculant/dual flocculation system, polyacrylamide-co-trimethyl ammonium ethyl acrylate chloride (TAEAC) polymers with varying molecular weights and structures were prepared for use of flocculants. The higher the cationic density of the polymer is higher, the higher was the conversion rate and the ratio of monomer. An acrylamide as nonionic monomer was less reactive than a TAEAC as cationic monomer. The branched polymer which was polymerized with a cross-linking agent, N, N-methylene bis-acrylamide had a higher stability and higher viscosity than a linear polymer but its dewatering efficiency was poor in a single flocculation system. In the case of single flocculant/dual flocculation, the branched polymer has better flocculation efficiency and the water content of the dewatered cakes was lower than the others, as the result of a re-flocculation effect. The optimum conditions for dual flocculation are a sequence in which the $1^{st}$ and $2^{nd}$ dosage are 75% and 25%/total dosage of a single flocculation system. The dewatering efficiency of a dual flocculation system is improved considerably from 10 to 25% under the experimental conditions used herein.

• Carbon letters
• /
• v.21
• /
• pp.1-7
• /
• 2017

The effects of ammonia-treated graphene oxide (GO) on composites based on epoxy resin were investigated. Ammonia solutions of different concentrations (14-28%) were used to modify GO. Nitrogen functional groups were introduced on the GO surfaces without significant structural changes. The ammonia-treated GO-based epoxy composites exhibited interesting changes in their mechanical properties related to the presence of nitrogen functional groups, particularly amine ($C-NH_2$) groups on the GO surfaces. The highest tensile and impact strength values were 42.1 MPa and 12.3 J/m, respectively, which were observed in an epoxy composite prepared with GO treated with a 28% ammonia solution. This improved tensile strength was 2.2 and 1.3 times higher than those of the neat epoxy and the non-treated GO-based epoxy composite, respectively. The amine groups on the GO ensure its participation in the cross-linking reaction of the epoxy resin under amine curing agent condition and enhance its interfacial bonding with the epoxy resin.

• Journal of Chest Surgery
• /
• v.23 no.3
• /
• pp.465-473
• /
• 1990

Glutaraldehyde have been used as the most effective cross-linking agent for stabilizing collagen fibers and preventing biodegradation. We processed bovine pericardium in a solution containing 0.625% glutaraldehyde,0.05M HEPES buffer and 0.26% magnesium chloride in saline. The glutaraldehyde-preserved bovine pericardium was implanted in 36 patients at Seoul National University Hospital during a 11-month period between May 1989 and March 1990. 24 were males and 12 females, with ages ranging from 6 months to 168 months [mean age of 43 months]. In 12 patients, the glutaraldehyde-preserved bovine pericardium was used for orthotopic reconstruction of the pericardial sac. In 24 patients. the glutaraldehyde-preserved bovine pericardium was heterotopically implanted.; pulmonary monocusp implant and RVQT [right ventricular outflow tract] patch widening were performed in 10 patients, pulmonary monocusp implant in 6, RVOT patch widening in 4, valved conduit in 2, conduit and pulmonary angioplasty in 1, and ventricular septation in l. With vascular suture techniques, the anastomoses were immediately tight. There was no bleeding from the needle holes and no oozing through bovine pericardium itself. During the follow-up period of up to 10 months, no infections of the glutaraldehyde-preserved bovine pericardium occurred and no bovine pericardium-related complications were observed in this series.

• Advances in materials Research
• /
• v.11 no.3
• /
• pp.191-209
• /
• 2022

Very slow degradation of synthetic based polymers has created a severe environmental issue that increased awareness towards research in polymers of biodegradable property. Soy protein isolate (SPI) is a natural biopolymer used as matrix in green composites but it has limitations of low mechanical properties and high water sensitivity. To enhance mechanical properties and reduce water sensitivity of Jute-SPI composites, SPI was modified with pine rosin which is also a natural cross-linking agent. 30% glycerol on the weight basis of a matrix was used as a plasticizer. The fibre volume fraction was kept constant at 0.2 whereas the pine rosin in SPI ranged from 5% to 30% of the matrix. The effects of pine rosin on mechanical, thermal, water sensitivity and surface morphology have been characterized using various techniques. The mechanical properties and water absorbency were found to be optimum for 15% pine rosin in Jute-SPI composite. Therefore, Jute-SPI composite without pine rosin and with 15% pine rosin were chosen for investigation through characterization by Fourier transforms infrared spectroscopy (FTIR), Thermo-gravimetric analysis (TGA), X-Ray diffraction (XRD) and Scanning electron microscope (SEM). The surface morphology of the composite was influenced by pine rosin which is shown in the SEM image. TGA measurement showed that the thermal properties improved due to the addition of pine rosin. Antimicrobial test showed antimicrobial property in the composite occurring 15% pine rosin. The research paper concludes that the modification of SPI resin with an optimum percentage of pine rosin enhanced mechanical, thermal as well as water-resistant properties of jute fibre reinforced composites.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.2
• /
• pp.645-655
• /
• 2019

In this study, colloidal microgel with viscoelasticity were prepared by using dispersion containing physical crosslinking agents and microgels with various strengths depending on the degree of cross-links.As the chemical crosslinking agent PEGDA400 content increased, hydrogels have various physical properties the swelling ratio decreased from $2.0{\times}10^4%$ to $6.0{\times}10^3%$ and increased viscosity by about 60%. The colloidal microgel was prepared with micro hydrogel grinded to $100{\mu}m$ size and the rheological behavior was confirmed with physical cross linking agent. A colloidal microgel having various viscosities was prepared by controlling starch and alginate based on micro-hydrogel containing 0.75% (w/v) of PEGDA400. In conclusion, these results would be highly useful for applying as a product that can give various physical properties to the colloidal suspensions, cosmetics, paint, and food industry.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.8-13
• /
• 2010

The physical properties of polymeric foams depend on the density of foams, physical properties of base polymers, the content of open cells, and cell structures including the size and its distribution, the shape of cell, and the thickness of skin layer. The foam density is affected by the chemistry of raw materials, the concentration of crosslinking agent and the blowing agent as well as the operating parameters during production process. In this study, the basic formulations of foams are composed of polyester polyol, MDI, amine catalyst, tin catalyst, silicone surfactant, and water. Cross-linking density of polyurethane was increased by using chain extenders. Also, the mechanical properties of polyurethane foam were improved by using the inorganic fillers (silica 1,2 and talc 1,2) having different $SiO_2$ contents and particle sizes. We investigated the properties of modulus, tensile strength, compressive strength and hardness of foams obtained by changing kind of inorganic filler and chain extender, and observed the distribution of inorganic filler as well as variation of cell size within the foams by electron microscopy.

• Clean Technology
• /
• v.19 no.3
• /
• pp.272-278
• /
• 2013

Ethylene propylene diene terpolymer (EPDM) has been usually used for various applications. Bottom ash generated in thermoelectric power plant is hardly recycled. In this study, EPDM/bottom ash/talc composites were prepared by using roll-mill. Bottom ashes obtained from thermoelectric power plant were modified using surfactant. The processing materials used in this study were antioxidant, processing oil, cross-linking co-agent and softening agent. Morphology and physical properties of EPDM composites are investigated by using SEM, TGA, UTM and Rheometer. As a result, when modified ash and talc are added to EPDM composites, the tensile strength and modulus of EPDM composites were remarkably enhanced.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.4
• /
• pp.200-207
• /
• 2006

In addition to the basic properties of the base and top coating agents, corrosion resistance of non-chrome magni 565 coating and characteristics of coating film when coated to steel substrate were studied. The system had a good wettability at room temperature. Moreover, both the contact angle and surface tension were affected little by the viscosity of coating agent and surface roughness of the steel substrate. And the samples coated with optimal conditions showed a great corrosion resistance in salt spray test with 1500 hours or longer of initial appearance time of rust. The coating film was composed of overlapping layer of zinc and aluminium flakes, and the thickness of base coat increased with an increase of base coat viscosity. Based on the C-F peaks of 1,1-Difluoroethaen homo-polymer, it was thought that the base coat was an inorganic polymer bond layer. Meanwhile, the top coat showed C-F peaks of polytetrafluoroethylene with C-H peaks of phenol in FT-IR analysis. From the lower weight loss of base coat in TG analysis, it was thought that cross linking density of base coat was larger than that of top coat. It was thought that the small exothermic reactions observed in DSC curves were due to the thermosetting resins contained in the coating agents. Compared to the non-coated specimen, the coated sample showed more higher polarization resistance and corrosion potential with lower corrosion current density.