• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.694-700
• /
• 1998

PSC box bridge by MSS construction method may not be set at cross section at one step. Web and bottom flange(U member) would be set at first, top flange will be set later with a time lag. In this case, U member and top flange concrete have different strain history. As two different aged section behaves as the composite section, there would happen the redistribution of stress. This is come from time-dependent strain characteristics of concrete itself. In this study, two models are considered, one with considering the set time of cross section and the other without. By performing longitudinal analysis of two models on considering construction stage, the stress differences of two are compared. As the analysis results show a considerable differences in the stresses of cross section between two models, the set time of cross section is needed for rational design f PSC box girder bridge.

• Transactions of Materials Processing
• /
• v.20 no.6
• /
• pp.450-455
• /
• 2011

This paper presents an inverse design methodology for the cross section geometry of mold spring with a rectangular cross section as the starting material for a coiling process. The cross-sections of mold springs are universally rectangular, as the parallel sides minimize the possibility of failure under high service loads. Pre-coiled wires are initially designed to have a trapezoidal cross section, which becomes a rectangle by the coiling process. This study demonstrates a numerical exercise to predict changes in the sectional geometry in spring manufacture and to obtain the initial cross section which becomes the exact rectangle desired from the manufacturing process. Finite element analysis was carried out to calculate the sectional changes for various mold springs. Geometrical parameters were the widths at inner and outer radii, the inner and the outer corner radii, and the height. A partial least square regression analysis was carried out to find the main contributing factors for deciding initial design values. The height and the width mainly affected various initial parameters. The initial width at the inner radius was mostly affected by various specification parameters.

• Structural Engineering and Mechanics
• /
• v.3 no.6
• /
• pp.555-567
• /
• 1995

Design curves have been prepared for prestressed rectangular beam section based on BS 8110, for determining area of steel for any given cross section, for stresses in concrete and steel and for the design moment. The design moment and the area of steel have been expressed in dimensionless form in terms of cross sectional dimensions and the characteristic strength of concrete. The choice and combination of design parameters result in considerably less number of curves as aid for design of rectangular prestressed beam sections, than those reported in CP 110 (Part 3).

• Korean Journal of Computational Design and Engineering
• /
• v.14 no.4
• /
• pp.234-241
• /
• 2009

The use of aluminum parts in automobile structuraI applications has increased in an effort to reduce the weight of cars and hence improve fuel economy. But Aluminum bar, I-beam and channels need other processes to vary the cross section in the axial direction. Thus, applications of these parts are limited by high cost. If the cross section of the part is variable by using only extrusion, application of extruded bar, I-beam and channels will increase in the Aluminum industries. In this paper, we propose the variable-shape extrusion process which can control the thickness of Aluminum bar. And we can calculate the speed of center ram by varying the cross section in the extrusion to control the thickness of Aluminum bar.

• Computers and Concrete
• /
• v.1 no.3
• /
• pp.303-324
• /
• 2004

The Component-Based Software Development (CBSD) has established itself as a sound paradigm in the software engineering discipline and has gained wide spread acceptance in the industry. The CBSD relies on the availability of standard software components for encapsulation of specific functionality. This paper presents the framework for the development of a software component for the design of general member cross-sections. The proposed component can be used in component-based structural engineering software or as a stand-alone program developed around the component. This paper describes the use-case scenarios for the component, its design patterns, object models, class hierarchy, the integrated and unified handling of cross-section behavior and implementation issue. It is expected that a component developed using the proposed patterns and model can be used in analysis, design and detailing packages to handle reinforced concrete, partially prestressed concrete, steel-concrete composite and steel sections. The component can provide the entire response parameters of the cross section including determination of geometric properties, elastic stresses, flexural capacity, moment-curvature, and ductility ratios. The component can also be used as the main computational engine for stand-alone section design software. The component can be further extended to handle the retrofitting and strengthening of cross-sections, shear and torsional response, determination of fire-damage parameters, etc.

• Wind and Structures
• /
• v.31 no.6
• /
• pp.523-532
• /
• 2020

As the height and flexibility of high-rise buildings increase, the wind loads become more dominant and the combination coefficient of Equivalent Static Wind Loads (ESWLs) should be considered when they are used in the structural design. In the first phase of the study, a brief introduction to the theory on the combination coefficient for high-rise buildings was given and then the time history of wind-induced responses of a 208-meter high-rise building with an elliptical cross-section was presented based on the wind tunnel test results for pressure measurement. The correlation between wind-induced responses was analyzed and the combination coefficients of ESWLs of the high-rise buildings using Turkstra's rule, and Asami's method, were calculated and compared with related design codes, e.g., AIJ-RLB, ASCE 7-10, and China Load Code for structural design. The results of the study showed that the combination coefficients from Asami's method are conservative compared with the other three methods. The results of this paper would be helpful to the wind-resistant design of high-rise buildings with elliptical cross-section.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.421-426
• /
• 2005

Scattering center extraction schemes for radar cross section reduction of large complex targets, like warships, was developed, which are an 1-D radar image method(range profile), and a direct analysis based on an object precision method. The analysis result of partial dihedral model shows that the presented direct analysis method is more efficient than the 1-D radar image method for scattering center extraction of interested targets, in terms of radar cross section reduction design, not signal processing. In order to verify the accuracy of the direct analysis method, a scattering center analysis of an naval weapon system was carried out, and the result was coincident with that of another well-known RCS analysis program. Finally, an analysis result of RCS and its scattering center of an 120m class warship-like model presented that the direct analysis method can be an efficient and powerful tools for radar cross section reduction of large complex targets.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.6
• /
• pp.37-46
• /
• 2013

Many factors about the stability for the reservoir embankments is determined when the facility is completed. Therefore the initial design of the embankment is important. Many researchers focused the effect of soil parameters although the cross section greatly affects the stability and can be controlled in design step. The objective of this research is to analysis of the effects for the safety factor of slope and seepage according to change cross-section in embankment. As a result, the quantity of seepage decreased as the gradient of downstream slope decreased and was proportional to the height of embankments. There was a linear relationship between the gradient of slope and the safety factor of slope. However the gradient of slope did not affect other side slope. All in a relationship, regressive equations with a high correlation coefficient were calculated and can be applied the simple estimation method of the stability using the cross-section. As results of analyzing the sensitivity, the friction angle and permeability critically effect for the slope stability and the seepage, respectively. The effect of the slope gradient was similar to major soil properties.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.133-139
• /
• 2000

Vibrational characteristics of the vehicle structure are mainly influenced by the shape of the pillar cross section. In this paper a vehicle structural optimization technique has been developed to investigate a lightweight vehicle structure subject to constraints on natural frequencies in a simple beam-and-shell model. In this technique, the optimization procedures involve two stages. In the first stage, the section procedures involve tow stages. In the first stage, the section properties of beam elements of the vehicle structure has been optimized to have minimum weight while satisfying the constraints of natural frequencies. And, in the second stage, the shape of the cross section of the elements of the structure has been determined.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2011

In this study the optimal stacking section was selected by pendulum impact test for six different stacking sections of the composite safety barrier. The beam cross-section shape was determined through the poll on six different beam cross-section shapes. The six kinds of stacking design for the determined beam cross-section were suggested. CSM, DB, DBT and Roving fibers were used for stacking design. Horizontal beam and 3:1 sloped beam were modeled by using LS-DYNA. The fall impact simulation was carried out by using rectangular pendulum and cylinder pendulum. Optimal stacking section was determined by comparing and analyzing the impact simulation results.