• KIPS Transactions on Software and Data Engineering
• /
• v.2 no.10
• /
• pp.661-668
• /
• 2013

A safety critical system is a system that leads to injury of people, damage of property and environment due to functional failures or occurrence of undesired condition. Therefore, to ensure the safety of a system, system engineers should consider the inherent hazards of the system at design phase of the system development, and also should design the prevention actions to minimize damage when an accident occurred. The objective of these actions is preventing the serious damage from accidents that can occur due to unforeseen circumstance. Recently, many studies have been performed to identify and analyze their hazards at design phase of safety critical systems. This paper suggests a safety analysis technique for analyzing the collision among those prevention actions to reduce accident and its effect by the collision of these actions that did not mentioned in previous studies. Through the proposed technique, it would improve robustness of safety and would help the design of prevention actions into system for the occurrence of accidents.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.107-114
• /
• 2012

Fracture of brittle material due to dynamic load such a particle impact has been reported by many researchers as the fracture behavior by variation of stress for a short minute. Especially, the brittle material, such a ceramic, applied to the structural component of machine, is considered as the important project. In order to evaluate the improvement of impact resistance, the particle impact test for the $Al_2O_3-TiO_2$ coated glass is practiced. And then, the damage variation according to the impact energy of steel ball was evaluated. There was a large improvement by the ceramic coating on the surface of a glass substrate. The damage volume was especially imported to evaluate damage behavior in quantity. These data were plotted on logarithmic coordinate and experimental equations were induced by data analysis based on test results. And the variation of critical energy for crack initiation was analyzed with critical impact energy when each crack occurs.

• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.671-678
• /
• 1998

Hertzian indentation tests with sphere indenters were used to study the mechanical properties of glass-in-filtrated alumina and spinel composites and evaluated the effect of preform microstructure and evaluated the effect of preform microstructure and glass con-tents on contanct damage and strength. The spinel composite showed more brittle behavior than the alumina composite which is verified from indentation stress-strain curve cone cracks and quasi-plastic deformation developed at subsurface. Failure originated from either cone cracks(brittle mode) or deformation zone(quasi-plastic mode) above critical load for cracking(Pc) and yield ({{{{ {P }_{Y } }}) with the brittle mode more dominant in the spinels and the quasi-plastic mode more dominant in the aluminas. Even though brittle mode was dominant in the spinel composites the strength degradation from accumulation of damage above these critical loads was conspicuously small suggesting that the glass-infiltrated composites should be highly damage tolerant to the blunt contacts.

• Proceedings of the Korean Reliability Society Conference
• /
• 2000.04a
• /
• pp.213-222
• /
• 2000

In present study, a stochastic model is developed for the low cycle fatigue life prediction and reliability assessment of 316L stainless steel under variable multiaxial loading. In the proposed model, fatigue phenomenon is considered as a Markov process, and damage vector and reliability are defined on every plane. Any low cycle fatigue damage evaluating method can be included in the proposed model. The model enables calculation of statistical reliability and crack initiation direction under variable multiaxial loading, which are generally not available. In present study, a critical plane method proposed by Kandil et al., maximum tensile strain range, and von Mises equivalent strain range are used to calculate fatigue damage. When the critical plane method is chosen, the effect of multiple critical planes is also included in the proposed model. Maximum tensile strain and von Mises strain methods are used for the demonstration of the generality of the proposed model. The material properties and the stochastic model parameters are obtained from uniaxial tests only. The stochastic model made of the parameters obtained from the uniaxial tests is applied to the life prediction and reliability assessment of 316L stainless steel under variable multiaxial loading. The predicted results show good accordance with experimental results.

• Journal of Korean Academy of Nursing Administration
• /
• v.16 no.1
• /
• pp.59-72
• /
• 2010

Purpose: This study is a descriptive research to analyze prognostic factors of barbiturate coma therapy (BCT) for severe brain damage patients, to develop a critical pathway (CP) based on the results of analysis and to examine the effect of its clinical application. Method: We analyzed medical records of 76 patients who received BCT for more than three days between January 1999 to July 2005. Based on the results of the analysis, we developed a CP and applied it to 12 people during August-December of 2005. Result: By application of BCT CP, the mortality rate decreased from 31.6% to 16.7%. It was found that the period of staying at ICU and total period of hospitalization were shortened by 2.78 (13.9%) days and 16.43 (29.4%) days, respectively. The Glasgow coma scale of the recovery group by CP application was 9.03 (4.64) at 72 hours post of BCT and 14.28 (1.82) at discharge from hospital, and DRS was 6.62 (6.38) points. Conclusion: By verifying clinical validity of the suggested CP, we believe that we have obtained visible effects standardizing the treatment pathway of BCT for brain damage patients.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.80-85
• /
• 1999

The purpose of this work is to investigate fatigue damage of quasi-isotropic laminates under tensile loading in different directions. Low cycle fatigue tests of [0/-60/+60]a laminates and [+30/-30/90]s lamina tes were carried out. Material systems used are AS4/Epoxy and AS4/PEEK. The fatigue damage of [+30/-30/90]s is very different from that of [0/-60/+60]s. The position of delamination generated at AS4/Epoxy and AS$/PEEK laminates were differentiated by the matrix difference that is, we suppose, the value of both GIcr(critical energy release rate of mode-I) and GIIIcr(critical energy release rate of mode-III) difference.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.1-3
• /
• 1996

The characteristics of fretting wear are reviewed. Fretting damage depends on slip amplitude and classified into three groups: (1) an annular damage according to Mindlin's analysis at microslip region, (2) strong adhesive deformation without loose wear particles at the intermediate region, and (3) formation of fine oxide particles at the gross slip region. The critical slip amplitude of fretting is the boundary between (2) and (3). The boundary slip amplitude depends on normal load. The wear rate increases and saturates with increasing slip amplitude. But it is constant by considering the critical amplitude. The role of oxide particles are discussed. Three different actions are noted: accelerating wear, preventing wear and insignificant effect. The oxide shows two opposing effect depends on normal load and slip amplitude. This is related to the removal rate from the interface (abrasive action) and compaction rate at the interface to form a protective layer. The effect of oxidation is significant to determine the wear and friction. The diffusion of oxygen is restricted at the small amplitude. As a result, crack formation at the boundary is a predominant damage, related to fretting fatigue damage.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1198-1205
• /
• 2003

Most domestic fossil power plant have exceeded 100,000 hours of operation with the severe operating condition. Among the critical components of fossil power plant, high temperature steam pipe system have had a many problems and damage from unstable displacement behavior because of frequent start up and shut down. In order to prevent the serious damage and failure of the critical pipe system in fossil power plant, 3-dimensional displacement measurement system were developed for the on-line monitoring system. 3-D Measurement system was developed with using the LVDT type sensor and rotary encoder type sensor, this system was installed and operated on the real power plant successfully. In the future time, network system of on-line diagnosis for critical pipe will be designed.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.303-313
• /
• 1997

Though many techniques for the damage assessment of structures have been studied recently, most of them can be only applied to simple structures. Therefore, practical damage assessment techniques that evaluate the damage location and the damage state for large structures need to be developed. In this study, a damage assessment technique using a neural network is developed, in which the bilevel damage assessment procedure is proposed to evaluate the damage of a large structure from the limited monitoring data. The procedure is as follows ; first, for the rational selection of damage critical members, the members that affect the probability of failure or unusual structural behavior are selected by sensitivity analysis. Secondly, the monitoring points and the number of sensors that are sensitive to the damage severity of the selected members are also selected through the sensitivity analysis with a proposed sensitivity measurement format. The validity and applicability of the developed technique are demonstrated by various examples, and it has been shown that the practical information on the damage state of the selected critical members can be assessed even though the limited monitoring data have been used.

• Journal of Korean Port Research
• /
• v.11 no.2
• /
• pp.281-294
• /
• 1997

Fatigue strength analysis is one of the most important themes of ship structure design, as fatigue damages are reported on ship structures even now. But these need basic research workes which will take time. The others are the problem to apply fatigue strength analysis in design and have to be investigated in parallel with basic researches. The one of major items in the latter is the critical damage factor to define with S-N curve for fatigue strength analysis of ship structure design.