• Journal of the Korean Society for Nondestructive Testing
• /
• v.10 no.1
• /
• pp.65-72
• /
• 1990

Comparison of acoustic emission, ultrasonic testing and crack gauge in 3-point bending testing have been studied. As the results, COD is indirectly assumed by strain gauge rate and grid pitch width when crack gauge grid is out. Acoustic emission is qualitatively able to measure crack growth by total count but ultrasonic testing has a difficulty in measuring it because of echo height fluctuation according to the change and pressure of UT. probe.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.635-638
• /
• 1999

The crack of concrete is one of the most important factors to evaluate the safety of the structures. The more important point for the safety-evaluation of the concrete structures is to check the crack development, the conventional window paper (Chang Ho Ji) have been used as a simple method in the past, and nowadays the strain gauge is used for more correct way to check the development of the concrete crack quantitatively. However the window-paper method is too simple and not so scientific, and the strain-gauge method is rather complicated for people in general. This Easy-Check Sensor provides the simple usage for the various concrete structures, but also the more correct results to evaluate the development of the concrete crack.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.4
• /
• pp.237-241
• /
• 2023

Recently, research on flexible sensors for personal health management has been gaining attention. In this study, we fabricated a crack-based flexible sensor in thin film form to measure the pulse on the wrist. We evaluated the characteristics of the sensor based on the curing conditions of the PDMS (Polydimethylsiloxane) film to optimize the sensor's gauge factor. The modulus of PDMS varies depending on the curing conditions. In this case, the modulus of PDMS has a significant influence on crack formation, leading to changes in the sensitivity of the sensor. This study examined the changes in the gauge factor associated with these variations.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.11-16
• /
• 1994

Acoustic emission technique is applied to the fatigue crack initiation in a carburized gear tooth. Acoustic emission test performed on carburized gear and three-point bending test equal to carburized gear hardness. The marked acoustic emission are detected at the early stage of crack initiation measured by a crack gauge and the final stage just before the tooth failure. The estimated acoustic emission energy rate are characteristic of the measured acoustic emission.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.10
• /
• pp.29-36
• /
• 2015

This paper deals with inspecting and monitoring cracks developed on a subway tunnel liner during the construction of temporary supports and excavation. The cracks have developed near a enlarged part of the tunnel. Several measurements, crack gauge, internal displacement measurement, 3-D laser scanner have been conducted to monitor the progress of cracks and effects of them on the tunnel. Local measurement, additional propagation of cracks and deformation of liner, have been conducted by crack gauge and internal displacement measurement. Global inspection has been conducted by 3-D laser scanner. From the scanned data, occurrence of global deformation of tunnel and rail has been evaluated. Because of limited sequence of construction at the ground, no apparent deformation of crack propagation has been measured. As presented in this paper, deformation of tunnel liner and effects of rail need to be investigated in view of local and global aspects.

• Smart Structures and Systems
• /
• v.32 no.4
• /
• pp.219-233
• /
• 2023

Crack width is an important indicator to evaluate the health condition of the concrete structure. The crack width is measured by manual using crack width gauge commonly, which is time-consuming and laborious. In this paper, we have proposed a fast and simplified crack width quantification method via deep Q learning and geometric calculation. Firstly, the crack edge is extracted by using U-Net network and edge detection operator. Then, the intelligent decision of is made by the deep Q learning model. Further, the geometric calculation method based on endpoint and curvature extreme point detection is proposed. Finally, a case study is carried out to demonstrate the effectiveness of the proposed method, achieving high precision in the real crack width quantification.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.140-145
• /
• 1997

In case of spot-welded joints, the fatigue cracks generally originate from the weld interfaces of the neighborhood nugget tips, and propagate toward the outer surfaces of the sheets. Generally, because fatigue crack was observed in nugget around, strain gage was attached at nugget zone. Accordingly, it was very difficult to detect the generation time of fatigue crack in spot-welded joints and to measure the propagation speed of fatigue crack. We developed the non-destructive method, according to which th fatigue crack propagation rate can be quantitatively estimated by utilizing information obtained from strain gages bonded on the electrode indentations of spot welds. The results measured by real crack were compared with the data which was measured by strain gauge method in fatigue testing. And so fatigue strength was evaluated by stress intensity factor. In this study behavior of fatigue crack propagation under repeated load were considered.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.896-902
• /
• 2000

Crack detection technique for concrete structures has been developed in this study,. The technique utilizes OTDR(Optical Time Domain Reflectometer) method that is widely used in the field of optical engineering. At present, some techniques, such as the naked eye inspection, inspection by crack gauge, ultra sonic detection and os on, are used for crack detection. However, these are not economical and are often time-consuming works. This method employs a common optical fiber as a means of crack detection. Th optical fiber is fully attached to concrete surface, and a crack on concrete could be detected to synchronize with the crack on optical fiber. The experimental verification was performed for concrete beams and the intial crack on the beam was detected under cracking force.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.4 no.2
• /
• pp.47-53
• /
• 1980

Kikukawa-Compliance method using a conventional clip-on gauge was employed to investigate fatigue crack growth and crack closure in 2017-T3 aluminum alloy. The crack growth rate plot against stress intensity range .DELTA.K on a log-log diagram exhibits a bilinear form with a transition at the growth rate of 10$\^$-4/ mm/cycle. The bilinear form appears still in the plot of growth rate versus effective stress intensity range .DELTA.K$\_$eff/. Fatigue crack growth rate could be well represented by .DELTA.K$\_$eff. The experimental results indicate that the effective stress intensity range ratio U depends on the maximum stress intensity factor K$\_$max/, but the stress ratio R does not affect U. The crack opening stress intensity factor K$\_$op/ tends to increase with increasing K$\_$max/ and decrease with increasing .DELTA.K.

• Explosives and Blasting
• /
• v.26 no.2
• /
• pp.77-91
• /
• 2008

According as demand for superannuated building increases recently, much researches about demolition method of construction are going on. This case study executed to center library building located in Dankook University. Explosives demolition method applied Progressive Collapse. Explosives demolition main blasting floors are 2, 4floor, assistance blasting floor is 1 floor. In the nearest distance (150 m), Vibration measurement result were 0.0302 cm/sec (PPV). Change was not in measurement value is crack gauge which install beforehand.