• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.696-704
• /
• 1991

ZrO2-Toughened Alumina-Ceramics (ZTA) with SiC Whisker as dispersive additive were prepared by pressureless sintering at 1$600^{\circ}C$ and 1$650^{\circ}C$ and by HIPing at 1$600^{\circ}C$ in Ar atmosphere. Effects of SiC-Whisker addition on microstuructural, mechanical, and thermal properties were investigated and the toughening mechanisms between theory and experiment were compared. Specimens with 15 vol% Whisker prepared by HIPing showed 8.26 MPa.ma1/2 in fracture toughness and 600 MPa in flexural strength owing to contribution of the three mechanisms such as crack deflection, whisker bridging and whisker pullout in spite of difference between the theoretical and experimental values due to the partial inhomogeneous dispersion of SiC-Whisker in the matrix and the processing flaw.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.121-124
• /
• 2005

A novel process to fabricate carbon nanotube (CNT)/alumina nanocomposites, consisting of a molecular level mixing process and an in situ spark plasma sintering process, is proposed. The CNT/alumina nanocomposites fabricated by this proposed process show enhanced hardness due to a load transfer mechanism of the CNTs and increased fracture toughness arising from the bridging mechanism of CNTs during crack propagation

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.88-95
• /
• 2001

Silicon nitride based ceramics reinforced with 3wt% Si$_{3}$N$_{4}$ whisker was prepared by tape casting to investigate the effect of microstructure on erosion behaviors. Hardness and fracture toughness were measured with prepared specimens. A gas blast type erosion tester was used to examine the erosion behavior of the specimens with different impact directions and angles. The erosion rate increases with increasing impact angle. Erosion rate of the silicon nitride ceramics also depends on the grain orientations, The erosion rate was lowered when impaction direction was parallel to the grain orientation This result was explained by the crack deflection and bridging due to the grain orientation.

• Journal of Powder Materials
• /
• v.13 no.1 s.54
• /
• pp.33-38
• /
• 2006

The effect of Cu content on microstructure and mechanical properties of nano-sized Cu dispersed $Al_2O_3(Al_2O_3/Cu)$ nanocomposites was investigated. The nanocomposites with Cu content of 2.5 to 10 vol% were prepared by reduction and hot-pressing of $Al_2O_3/CuO$ powder mixtures. The nanocomposites with Cu content of 2.5 and 5vol% exhibited the maximum fracture strength of 820MPa and enhanced toughness compared with monolithic $Al_2O_3$. The strengthening was mainly attributed to the refinement of $Al_2O_3$ matrix grains. The toughening mechanism was discussed by the observed microstructural feature based on crack bridging.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.669-672
• /
• 2006

Recently, large efforts have been made to develop and understand the behavior of Fiber Reinforced Concrete. As in the static loading cases, many researches have been done. However, a few studies have been conducted in cyclic behaviors of FRC. The main objective of the present work is to investigate the cyclic behavior of fiber reinforced concrete with theoretical method. First, cyclic constitutive relations which describe the crack bridging stress considering non-uniform interfacial bond degradation in short randomly oriented fiber reinforced matrix composites under uniaxial cyclic tension were considered. A cyclic degradation model of single fiber based on micromechanics also taken into consideration. As an example, fatigue analysis for ECC with PVA fiber was conducted using proposed equations. Results shows that proposed method can establish a basis for analyzing cyclic behavior of fiber reinforced composites.

• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.617-622
• /
• 1992

In order to study on the effect of SiC whisker in flexural strength characterization of macro defect-free (MDF) cement composites, which composed of high alumina cement and polyvinyl alcohol, microstructural characterization of the composite specimens fabricated by the addition of SiC whiskers was investigated. Microproes are created around the SiC whisker, MDF cement didn't react with the SiC whisker. However, flexural strength of the composites have been improved. Fracture morphology of the composites, presents mainly intergranular type fracture passing around the unhydrated particles and siC whiskers, and partially transgranular type fracture. The main strengthening mechanisms of the MDF cement composites reinforced with SiC whiskers are characterized by crack deflection, microcracking, and bridging of cracks.

• Journal of Powder Materials
• /
• v.7 no.3
• /
• pp.149-153
• /
• 2000

In this study, the fabrication of $Al_2O_3$/5vol.%Cu nanocomposite and its mechanical property were discussed. The nanocomposite powders were produced by high energy ball milling of $Al_2O_3$ and Cu elemental powders. The ball-milled powders were sintered with Pulse Electric Current Sintering (PECS) facility. The relative densities of specimens sintered at $1200^{\circ}C$ and $1250^{\circ}C$ after soaking process at $900^{\circ}C$ were 96% and over 97%, respectively. The sintered microstructures were composed of $Al_2O_3$ matrix and the nano-sized Cu particles distributed on grain boundaries of $Al_2O_3$ matrix. The nanocomposite exhibited the enhanced fracture toughness compared with general monolithic $Al_2O_3$. The toughness increase was explained by the crack deflection and bridging by dispersed Cu particles.

• Journal of the Korea Concrete Institute
• /
• v.19 no.2
• /
• pp.153-161
• /
• 2007

This paper investigates the lap splice performance of structural steel bars embedded in high performance fiber reinforced cementitious composite(HPFRCC) with various matrix ductilities. Matrix ductility is governed fiber type and fiber volume fraction. Fiber types were polypropylene(PP), polyethylene(PE) and hybrid fiber[polyethylene fiber+steel cord(PE+SC)]. The lap splice length$(l_d)$ was calculated according to the relevant ACI code requirements for reinforcing bars in normal concrete. As the result of tests, lap splice strength of HPFRCC using PE1.5 and hybrid fiber increased by up to $82{\sim}91$ percent more than that of concrete. Splice strength and energy absorption capacity of PE0.75+SC0.75 or PE1.5(fiber volume fraction 1.5%) specimen increased more than that of PP2.0(fiber volume fraction 2.0%) specimen. Therefore lap splice performance depends on fiber tensile strength and Young's modulus more than fiber volume fraction. Also, HPFRCC appear multiple crack and ductile postpeak behavior due to bridging of fiber in cementitious composite.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1913-1915
• /
• 1999

The ${\beta}-SiC+ZrB_2$ ceramic composites were hot-press sintered and annealed by adding 1, 2, 3wt% $Al_2O_3+Y_2O_3$(6 : 4wt%) powder as a liquid forming additives at $1950^{\circ}C$ for 4h. In this microstructures, no reactions were observed between $\beta$-SiC and $ZrB_2$, and the relative density is over 90.79% of the theoretical density and the porosity decreased with increasing $Al_2O_3+Y_2O_3$ contents. Phase analysis of the composites by XRD revealed of $\alpha$-SiC(6H, 4H), $ZrB_2$, $Al_2O_3$ and $\beta$-SiC(15R). Flexural strength showed the highest of 315.46MPa for composites added with 3wt% $Al_2O_3+Y_2O_3$ additives at room temperature. Owing to crack deflection and crack bridging of fracture toughness mechanism, the fracture toughness showed the highest of $5.5328MPa{\cdot}m^{1/2}$ for composites added with 2wt% $Al_2O_3+Y_2O_3$ additives at room temperature.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.75-77
• /
• 2001

The mechanical and electrical properties of the pressureless annealed SiC-$TiB_2$ electro conductive ceramic composites were investigated as functions of the transition metal of $TiB_2$. The result of phase analysis for the SiC-$TiB_2$ composites by XRD revealed $\alpha$-SiC(6H). $TiB_2$, and YAG($Al_5Y_3O_{12}$) crystal phase. The relative density showed the lowest 84.8% for the SiC-$TiB_2$ composites added with 39vol.%$TiB_2$. Owing to crack deflection, crack bridging and YAG of fracture toughness mechanism, the fracture toughness showed the highest value of $7.8\;MPa{\cdot}m^{1/2}$ for composites added with 39vol.%$TiB_2$ under a pressureless annealing at room temperature. The electrical resistivity of the SiC-27vol.%$TiB_2$ composites was negative temperature coefficient resistance(NTCR), and the electrical resistivity of the besides SiC-27vol.%$TiB_2$ composites was all positive temperature coefficient resistance(PTCR) in the temperature range of $25^{\circ}C$ to $700^{\circ}C$.