• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.4
• /
• pp.1458-1470
• /
• 2018

In this letter, a new dual-port Multiple-Input Multiple-Output (MIMO) antenna is introduced which has two independent signal feeding ports in a single antenna element to achieve smaller antenna volumes for the 5G mobile applications. The dual-port structure is implemented by adding a cross coupled semi-loop (CCSL) antenna as the secondary radiator to the ground short of inverted-F antenna (IFA). It is found that the port to port isolation is not deteriorated when an IFA and CCSL is combined to form a dual-port structure. The isolation property of the proposed antenna is compared with a polarization diversity based dual-port antenna proposed in the literature [9]. The operating frequency range is 3.3-4.0 GHz which is suitable for places where $4{\times}4$ MIMO systems are supposed to be deployed such as in China, EU, Korea and Japan at the band ${\times}$ (3.3 - 3.8GHz. The measured 6-dB impedance bandwidths of the proposed antennas are larger than 700 MHz with isolation between the feeding ports higher than 18 dB [1-2]. The simulation and measurement results show that the proposed antenna concept is a very promising alternative for 5G mobile applications.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.1
• /
• pp.27-33
• /
• 2001

This article describes an observation that the aperture coupling mechanisms in the aperture coupled microstrip antenna can be divided into two categories, cavity and parasitic types, depending on the separation between the microstrip patch and the ground plane. The similar phenomenon was observed in the relatively simple gap coupled microstrip antenna. The specific characteristics between two coupling mechanisms is discussed.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.6
• /
• pp.1033-1038
• /
• 2022

In this paper, the design of a printed dipole antenna fed by broadside coupled striplines (BCS) for the 3.5GHz band is described. The two fins of the bow tie are, respectively, on the two sides of the substrate. The feeding balanced lines adopted for 1×2 array are the BCS. The obtained numerical results are in good agreement with experimental data. Through experiments with printed dipole antennas of various extended angles, the printed dipole antenna exhibits the wide bandwidth in the desired frequency band, which has a bandwidth of 28% for VSWR < 2.0 : 1. And within this bandwidth, This printed dipole antenna achieves a stable radiation pattern. It is found that the narrow band and feeding for array characteristic which is a disadvantage of the conventional printed dipole antenna can be improved. The radiation pattern showed omnidirectional characteristics and the maximum gain was about 4.4dBi.

• 한국ITS학회:학술대회논문집
• /
• 2008.11a
• /
• pp.386-390
• /
• 2008

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.369-373
• /
• 2000

This paper describes a design for microstrip EMC cross dipole array antenna with circular polarization. To realize the wide bandwidth and circular polarization, the electromagnetic-coupled cross dipole is used. To obtain the uniform aperture illumination, offset technique for array is adopted. In 20-element array design, the calculated axial ratio and gain are about 0.1 dB and 9.9 dBi at 12GHz, respectively. The frequency characteristics of a fabricated 20-element array antenna are measured. The calculated results agree well with the measured ones.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1664-1667
• /
• 2003

Aperture-coupled microstrip antenna is one type of microstrip antennas. This type of antenna has bandwidth wider than simple microstrip antenna. Herein, we use two substrates, that have the same dielectric constant 2.47 (PTFE-quartz) in which upper substrate is a rectangular patch. The microstrip patch is fed by a microstrip line which is printed on lower substrate, through an aperture or slot in the common ground plane of patch and microstrip feed. This antenna is analyzed by using Finite Difference Time Domain (FDTD) method the specific design frequency 10 GHz and match impedance is 50 ohms. The simulation results of its characteristics are input impedance, return loss, VSWR and radiation patterns respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.128-131
• /
• 2000

This paper describes design for dual-linear polarization antenna using EMC(electromagnetic-coupled) dipole. EMC dipole has a simple element structure and it is fed by microstrip line. Vortical and horizontal polarization are determined by structure of dipole fed by microstrip line. FDTD Method is used for an analysis of antenna element. Length, width, height and offset of dipole are designed for 1-element antenna. Resonant length of diploe differs from the calculated value by a formula because of coupling effect of dipole and feed line. Radiation Power is controlled by the offset of dipole. In prectical fabrication of antenna array, a constant height of dipoles is required. Therefore, the teflon plate with height of 0.8 mm is considered in antenna element design for the vertical polarization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.178-183
• /
• 2006

The proposed triple-band compact chip antenna using coupled meander line and stacked meander structure for mobile RFID/PCS/WiBro. The proposed antenna is designed to operate at 900, 1,800, and 2,350 MHz, and is realized by parasitic coupled and stacked a meander line. Meander lines are using extend length of effective current path more than monopole and contribute miniaturization. The coupled meander line controls the excitations of the mobile RFID and PCS, stacked meander line controls the excitation of the WiBro. The fabricated antenna size is $10.98{\times}22.3{\times}0.98\;mm$. The resonance frequencies are 905 MHz, 1.77 GHz and 2.32 GHz. The impedance bandwidths are 24 MHz, 140 MHz and 92 MHz. The maximum gains of antenna are 0.34 dBi, 2.58 dBi and 0.4 dBi at resonance frequencies.

• Journal of Digital Contents Society
• /
• v.10 no.3
• /
• pp.389-393
• /
• 2009

In this paper, the single patch microstrip antenna and gap coupled broadband microstrip patch antenna using FDTD(Finite Difference Time Domain method) are analyzed. Mur's 2nd absorbing boundary condition to minimize reflected wave is applied. Return loss, voltage standing wave ratio, and input impedance by the length and width of driving patch, the length and width of parasitic patch, and the distance between driving patch and parasitic patch have been analyzed. Design parameters and radiation patterns of broadband antenna have been also shown.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1511-1517
• /
• 2000

A new slot-coupled back-to-back microstrip array antenna is proposed for using in the IMT-2000 base station or repeater antenna. This antenna is composed of symmetrical SSAIP(Strip Slot, Air Inverted Patch) It has bidirectional radiation pattern in horizontal plane and 22.5$^{\circ}$main beam squint in vertical plane. The analysis is based on the cavity model and the design is achieved using Ensemble. Experimental results for the radiation pattern and the return loss have shown that the direction of the main beam is about 21$^{\circ}$and the impedance bandwidth is approximately 22.9% Thus the proposed antenna is able to operate over both uplink and downlink frequencies in IMT-2000.