• 대한기계학회논문집B
• /
• 제28권5호
• /
• pp.612-618
• /
• 2004

Stereoscopic PIV measurements were made in the wind tunnel with the actual size waterjet model. The main wind tunnel provides the vehicle velocity while the secondary wind tunnel adjusts the jet issuing velocity. Experiments were performed at the range of jet to vehicle velocity ratio (JVR), 3.75 to 8.0 and the Reynolds number of 220,000 based on the jet velocity and the hydraulic diameter of the waterjet intake duct. Wall pressure distributions were measured for various JVRs. Three dimensional velocity fields were obtained at the inlet and outlet of the intake duct. It is found that severe acceleration is occurred at the lip region while deceleration is noticeable at the ramp side. The detailed three dimensional velocity fields can be used as the accurate velocity input for the CFD simulation. It is interesting to note that there are many different types of vortices in the instantaneous velocity field. It can be considered that those vortices are generated by the corner of rectangular section of the intake and Gortler vortices due to the curved wall. However, typical secondary flow with a pair of counter rotating vortex pair is clearly seen in the ensemble averaged velocity field.

• 대한기계학회논문집B
• /
• 제22권12호
• /
• pp.1735-1745
• /
• 1998

Oil-film surface flow visualizations and three-dimensional flow measurements using a straight five-hole probe have been conducted for a circular impinging jet which is normally oriented to the crossflow in a channel. Throughout the experiments, the ratio of channel height to injection hole diameter, H/D, is fixed to be 1.0, and blowing ratio is varied to be 1.0, 2.0, 3.0 and 4.0. From the surface flow visualizations for both top wall(target plate) and bottom wall, impinging jet region on the target plate can be clearly identified, and for the small value of H/D = 1.0, presence of the bottom wall changes the near-hole flow structure, significantly. The three-dimensional flow measurements show that in the dawnstream region of the injection hole, there exist a pair of counter-rotating vortices, called "scarf vortices", and the strength of the vortices strongly depends on the blowing ratio. In addition, a new flow model in the flow symmetry plane has been proposed for H/D = 1.0.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권4호
• /
• pp.437-442
• /
• 1997

An experimental study was carried out in a channel cavity with square heat surface by visual¬ization equipment with Mach - Zehnder interferometer and laser apparatus. The image processing system consists of one commercial image board slit into a personal computer and 2-dimensional sheet light by Argon-Ion Laser with cylindrical lens and flow picture recording system. Instant simultaneous velocity vectors at whole field were measured by 2-D PIV system which adopted two¬frame grey-level cross correlation algorithm. Heat source was uniform heat flux(o.4W/cm$^2$, , O.8W/cm$^2$, 1.2W/cm$^2$). Obtained result showed various flow patterns such as kinetic energy distribution. Severe unsteady flow fluctuation within the cavity are remarkable and sheared mixing layer phenomena are also found at the region where inlet flow is collided with the counter-clockwise rotating main primary vortex. Photographs of Mach ~ Zehnder are also compared in terms of constant heat flux.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.378-385
• /
• 2012

벤트 혼합기는 혼합기 후류에 존재하는 재순환 영역으로 공기를 유입시켜 연료-공기 혼합을 증대시키는 혼합기이다. Stereoscopic PIV기법을 통해 얻은 3차원 속도, 와류, 난류운동에너지를 토대로 계단형 혼합기를 기본 모델로 하여 벤트 혼합기의 성능을 분석하였다. 벤트 혼합기는 두터운 전단층으로 인해 높은 침투거리를 보였으며, 난류운동에너지는 주로 주유동과 제트유동의 경계면을 따라 분포하였다. 이 난류 영역은 혼합영역 내에서 활발히 물질전달을 일으키며, 혼합 증대를 가져온다.

• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1640-1649
• /
• 2001

The present study investigates the effects of various rib arrangements on heat/mass transfer in the cooling passage of gas turbine blades. A complex flow structure occurs in the cooling passage with rib turbulators which promote heat transfer on the wall. It is important to increase not only the heat transfer rates but also the uniformity of heat transfer in the cooling passage. A numerical computation is performed using a commercial code to calculate the flow structures and experiments are conducted to measure heat/mass transfer coefficients using a naphthalene sublimation technique. A square channel (50 mm $\times$ 50 mm) with rectangular ribs (4 mm $\times$ 5 mm) is used fur the stationary duct test. The experiments focus on the effects of rib arrangements and gap positions in the discrete ribs on the heat/mass transfer on the duct wall. The rib angle of attack is 60°and the rib-to-rib pitch is 32 mm, that is 8 times of the rib height. With the inclined rib angle of attack (60°), the parallel rib arrangements make a pair of counter rotating secondary flows in the cross section, but the cross rib arrangements make a single large secondary flow including a small secondary vortex. These secondary flow patterns affect significantly the heat/mass transfer on the ribbed wall. The heat/mass transfer in the parallel arrangements is 1.5 ∼2 times higher than that in the cross arrangements. However, the shifted rib arrangements change little the heat/mass transfer from the inline rib arrangements. The gap position in the discrete rib affects significantly the heat/mass transfer because a strong flow acceleration occurs locally through the gap.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.91-98
• /
• 1999

This paper describes the air flow characteristics inside the throttle valve. Tow-dimensional steady incompressible Navier-Strokes equation are solved numerically with embedding the conceopt of the artificial compressibility and adopting the Baldwin-Lomax turbulence model. With varying the valve opening angles(the Reynolds number )such as 15$^{\circ}$(5000) , 45$^{\circ}$(3000) , 75$^{\circ}$(7000) and 90$^{\circ}$(10000), respectively. tow cases, with a valve shaft and without one, are analysed. The pressure loss between the entrance and exit is severe at 15$^{\circ}$, 100 times as larger as that of 90$^{\circ}$ case, which also depends much on the existece of the valve shaft. The counter rotating vortices are formed over the valve plate with the shaft at only 75$^{\circ}$. They are smally and very large scale in front and back of the valve shaft , respectively. The velocity profiles of 15$^{\circ}$ and 90$^{\circ}$ at the exit are almost symmetric to the horizontal center line, however, the symmetricity is no longer maintained at 45$^{\circ}$ and 75$^{\circ}$ , and in addition, the flow at 75$^{\circ}$ is enforced a lot below center line. The pressure distribution on the walls is largely changed near the valve shaft, and its magnitude becomes great as the valve angle decreases.

• 한국추진공학회지
• /
• 제16권4호
• /
• pp.50-56
• /
• 2012

벤트 혼합기는 혼합기 후류에 존재하는 재순환 영역으로 공기를 유입시켜 연료-공기 혼합을 증대시키는 혼합기이다. Stereoscopic PIV기법을 통해 얻은 3차원 속도, 와류, 난류운동에너지를 토대로 계단형 혼합기를 기본 모델로 하여 벤트 혼합기의 성능을 분석하였다. 벤트 혼합기는 두터운 전단층으로 인해 높은 침투거리를 보였으며, 난류운동에너지는 주로 주유동과 제트유동의 경계면을 따라 분포하였다. 이 난류 영역은 혼합영역 내에서 활발히 물질전달을 일으키며, 혼합 증대를 가져온다.

• 한국항공우주학회지
• /
• 제43권2호
• /
• pp.109-117
• /
• 2015

덕트는 항공기의 내부엔진에 외부 공기를 흡입하기 위한 장치이다. 엔진 입구면의 레이더 반사량을 줄여 피탐지성을 감소시키기 위하여 S형태의 덕트를 가지게 되었다. S-Duct는 중심선의 곡률, 입구형상 등의 형상변수에 따라 엔진의 성능에 영향을 미친다. 본 연구에서는 RAE M 2129 S-Duct의 입구형상에 대하여 가로세로비의 변경에 따른 덕트 내부 유동에 대한 유동 특성을 알아보기 위해 전산해석을 수행하였다. S-Duct의 성능 평가 기준으로는 유동 왜곡계수를 사용하였다. 공력해석을 위해 상용해석 소프트웨어를 사용하였으며, 벽면에서의 역압력 구배의 영향으로 발생하는 유동박리와 2차 유동을 예측하기 위하여 $k-{\omega}SST$ 난류모델을 사용하였다. S-Duct의 Port side와 Starboard side 각각의 압력분포 값에 대하여 ARA의 실험값과 비교하여 본 연구에서 사용된 전산해석 기법의 타당성을 검증하였다. 해석 결과 모든 형상에 대하여 유동박리와 2차 유동이 발생하는 것을 확인하였다. 반원형 형태의 입구형상을 가지는 S-Duct가 뛰어난 성능을 보임을 확인하였다.