• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.115-127
• /
• 2019

The low-flow grouting injection technique, the target construction method for this study, is a method of pouring mortar into the ground by non-emission replacement principle, which can be expected to increase the density of the ground, and, in some cases, be used as a base file using the strength of the high injection solids, along with low noise, low pollution, and high durability. To verify that the dynamic characteristics of the ground are improved by the low-flow injection technique, the test work was conducted on the site and physical tests were performed, and the quality of the improvement formed in the ground was verified through the indoor test on the core and core recovery rate was analyzed. The density logs test layer calculated the volume density of the ground layer by using the Compton scattering of gamma-rays, and the sonic logs was tested on the ground around the drill hole using a detector consisting of sonar and receiver devices inside the drill hole. As a result of the measurement of the change in physical properties (density and sonic logs) before and after grouting, both properties were basically increased after infusion of grout agent. However, the variation in density increase was greater than the increase in speed after grouting, and the ground density measurement method was thought to be effective in measuring the fill effect of the filler. Strength and core recovery rates were measured from specimens taken after the age of 28 days, and the results of the test results of the diffusion and strength test of the improved products were verified to satisfy the design criteria, thereby satisfying the seismic performance reinforcement.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.942-943
• /
• 2008

The boost converter is usually used in power factor correction. The dynamic losses of its output diode are produced during the reverse recovery time. The power efficiency is decreased due to the losses and also it generates the noise. These disadvantages have been remarkably improved by ZCS and ZVS techniques of power factor improvement circuit. Some benefits lead to the achievement of higher power density and the development cost can be decreased. In this paper work, the reverse recovery suppression(RS) PFC method is used. A inductor and a diode are added into the conventional circuit. The switching device, MOSFET is turned off after the reverse recovery current has come to the zero level. The Zero Current Switching(ZCS) is implemented at that time. This power conversion technique improves the efficiency to about 1% and reduces the noise obviously. And the additional inductor can be designed using an original filter core in the circuit. The converter size is reduced effectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.8
• /
• pp.62-68
• /
• 2014

The series connection type superconducting fault current limiter (SFCL) with added third winding, which was magnetically coupled in one iron core, was proposed. The proposed SFCL was expected to be more improved by just adding third winding into the conventional series connection type SFCL with two coils. To analyze the contribution of the third winding for the current limiting and the recovery characteristics of the SFCL, the short-circuit tests for the series connection type SFCL with the added third winding were performed together with the analysis on its electrical equivalent circuit. From the comparative analysis on the amplitude of the limited fault current and the power burden of the high-TC superconducting (HTSC) element comprising this SFCL, the improved current limiting and recovery characteristics of the series connection type SFCL using the third winding could be confirmed.

• Journal of Photoscience
• /
• v.9 no.3
• /
• pp.65-70
• /
• 2002

In the rice leaves treated with methyl viologen (MV), the photochemical efficiency of PSII (or $F_{v/}$F $m_{m}$) was significantly decreased, and significant portion of the photoinactivation process was reversible during the dark-recovery. The dark-reactivation process was relatively slow, reaching its plateau after 2-2.5 h of dark incubation. The damaged portion of functional PSII was 13％, based on the value of I/ $F_{o}$- I/ $F_{m}$ after this dark-recovery period. The reversible photoinactivation process of PSII function in the MV-treated leaves consisted of a xanthophyll cycle-dependent development of NPQ and a xanthophyll cycle-independent process. The latter process was reversible in the presence of nigericin. As well as the increase in the values of Chl fluorescence parameters, the epoxidation process during the dark-recovery after the MV-induced photooxidation was very slow. These results suggest that the photooxidative effect of MV is partly protected by the down-regulation of PSII before inducing physical damages in core proteins of PSII.I.I.I.I.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.9
• /
• pp.4572-4586
• /
• 2019

Mobile Edge Computing (MEC) and Information-Centric Networking (ICN) are essential network architectures for the future Internet. The advantages of MEC and ICN such as computation and storage capabilities at the edge of the network, in-network caching and named-data communication paradigm can greatly improve the quality of video streaming applications. However, the packet loss in wireless network environments still affects the video streaming performance and the existing loss recovery approaches in ICN does not exploit the capabilities of MEC. This paper proposes a Deep Learning based Loss Recovery Mechanism (DL-LRM) for video streaming over MEC based ICN. Different with existing approaches, the Forward Error Correction (FEC) packets are generated at the edge of the network, which dramatically reduces the workload of core network and backhaul. By monitoring network states, our proposed DL-LRM controls the FEC request rate by deep reinforcement learning algorithm. Considering the characteristics of video streaming and MEC, in this paper we develop content caching detection and fast retransmission algorithm to effectively utilize resources of MEC. Experimental results demonstrate that the DL-LRM is able to adaptively adjust and control the FEC request rate and achieve better video quality than the existing approaches.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.21-29
• /
• 2012

A dual loop waste heat recovery system with Rankine steam cycles for the improvement of fuel efficiency of gasoline vehicles has been investigated. A high temperature loop (HT loop) only recovers the heat of the exhaust gas. A low temperature loop (LT loop) recovers the residual heat from the HT loop, the coolant heat and the remaining exhaust gas heat. The two separate loops are coupled with a heat exchanger. This paper has dealt with a layout of the dual loop system, the review of the working fluids, and the design of the cycle. The design point and the target heat recovery of the HT boiler, a core part of a HT loop, have been presented. The prototype of the HT boiler was evaluated by experiment. For the performance evaluation of the HT boiler, inlet temperature of the HT boiler working fluid was set equal to the temperature degree of sub-cool of $5^{\circ}C$ at the condensing pressure. The exit condition was the degree of super-heat set at $5^{\circ}C$. The characteristics of the HT boiler such as heat recovery and pressure drops of fluids were evaluated with varying flow rates and inlet temperatures of exhaust gas under various evaporating pressure conditions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.13 no.1 s.29
• /
• pp.79-87
• /
• 1989

In the part 1 and 2, relations were found between fundmental mechanical properties and primary hand values, performance of Korean women's summer and fall & winter fabrics. In this paper, in order to investigate the hand values and mechanical properties such as tensile, shearing, bending, compression, surface and thickness & weight of the core-spun yarn woven fabrics for Korean folk clothes were measured by KES-F system. The experimental results are statistically analyzed in the aspects of the mechanical properties, their effects on the hand values, formation of weared clothes and transformation behavior. The correlation in the hand values are analyzed, too. Furthermore, there mechanical properties are discussed in comparison with those values for kimono fabrics. The main results are summarized as follows: 1. The core-spun yarn woven fabrics for Korean folk clothes have box-shaped silhouette based on higher bending rigidity and shear elasticity. 2. The core-spun yarn woven fabrics for Korean folk clothes are inferior to silk fabrics, superior to polyester fabrics in formation. 3. A drapability and wrinkle recovery of core-spun yarn woven fabrics for Korean folk clothes formation for weared clothes are inferior to polyester fabrics, superior to silk fabrics. 4. A primary factor of mechanical properties contribute to the hand values of core-spun yarn woven fabrics for Korean folk clothes are same as the Korean women's winter fabrics, except for flexibility with soft feeling. 5. As for the hand values of core-spun yarn woven fabrics for Korean folk clothes, stiffness, anti-drape stiffness are superior to those of polyester fabrics. And also, flexibility with soft feeling, scrooping feeling of core-spun yarn woven fabrics have greater values as compared with silk fabrics for Korean folk clothes.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.3
• /
• pp.110-116
• /
• 1992

Electromgnetic joining of aluminum alloy tubes to high toughness polyurethane rubber cores is studied in order to estimate the joining strength and to analyze the effect of the process variables. The equation which can estimate the joining strength is proposed under considering the elastic recovery of the polyurethane core and the radial shrinkage of the core by pulling it axially. The obtained results are as follows : 1) The joining strength is mainly dependent on the magnitude of residual elastic strain of the polyurethane core. 2) The radial shrinkage (residual strain reduction) of the core during the axial pulling causes the joining strength to decrease severely. The equation for the reduced axial strength is proposed and it is found that the estimated values agree well with experimental results. 3) The magnitude of radial shrinkage could be reduced for the smaller value of ratio l/r. 4) The joining strength in metal/polymer joining increases as the friction coefficient increases. But its effect of friction coefficient is insignificant in comparison with the case of metal/metal joining.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.22 no.2
• /
• pp.240-249
• /
• 2016

Purpose: The purpose of this study was to identify the factors influencing personal disaster preparation and disaster nursing core competency among visiting nurses in public health centers. Methods: A descriptive survey study was adopted. A convenience sample was taken from 277 subjects in three regions. Data were analyzed by descriptive statistics, t-test, ANOVA, correlation, Pearson correlation coefficient and multiple regression. Results: The mean personal disaster preparation and disaster nursing core competency scores were 11.13 and 76.87, respectively. Personal disaster preparation was statistically significant by experience of disaster victims and disaster management guideline. Disaster nursing core competency was statistically significant by participation in future disaster recovery. As a result of multiple regression analysis, personal disaster preparation accounted for 14.9 of the variance by experience of disaster victims and disaster management guidelines; disaster nursing core competency accounted for 8.9 of the variance by perception of disaster nursing. Conclusion: Although visiting nurses are ill-prepared for disaster, global natural and man-made disasters can occur regardless of time and place. Disaster education and training should therefore be included in nurses' fundamental education.

• Smart Structures and Systems
• /
• v.25 no.3
• /
• pp.337-343
• /
• 2020

In this paper, we focused on the self-healing concrete using new nano-capsules. Three types of nano-capsules with respect to availability, high strength and temperature tolerance are used; type 1 is URF and polyethylene (PE) as shell and nano titanium oxide (TiO₂) as core, type 2 is URF and PE as shell and nano silica oxide (SiO₂) as core, type 3 is PE as shell and nano silica oxide (SiO₂) as core. The concrete samples mixed by nano-capsules with three percents of 0.5, 1 and 1.5. Based on experimental tests and the compressive strength of samples, the URF-PE-SiO₂ is selected for additional tests of compressive strength before and after recovery, ultrasonic test, ion chlorine and water penetration depths. After careful investigation, it is concluded that the optimum value of URF-PE-SiO₂ nano-capsules is 0.5% since leads to higher compressive strength, ultrasonic test, ion chlorine and water penetration depths.