• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1185-1191
• /
• 2008

The core design technology for the multi-effect desalination plant using the thermo compressor (MED-TVC) was investigated by the performance test of multi effect desalination plant in this paper. The final G.O.R (gain of output ratio) of MED-TVC type desalination plant is strongly affected by the performance of thermo-vapor compressor. The present experiments for the desalinating capacity and G.O.R were obtained for the range of the motive steam pressure, 266.0, 250.0, 230.0 and 200.0 kPa. And as a practical problem, to investigate the influence of the sea water temperature to the G.O.R, the inlet steam temperature of the suction water vapor was changed in the range of $311.2{\sim}324.2$ K in the present experiment. Through the experiments, the maximum value of G.O.R was 8.5 at the condition of the motive steam pressure, 136.0 kPa and the minimum value of G.O.R was 8.1 at the condition of the motive steam pressure, 266.0 kPa. And it was confirmed that the range of desalination capacity was $355.2{\sim}264.0$ ton/day in the normal operation condition.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.41-48
• /
• 2012

A numerical analysis of thermal stratification in the upper plenum of the MONJU fast breeder reactor was performed. Calculations were performed for a 1/6 simplified model of the MONJU reactor using the commercial code, CFX-13. To better resolve the geometrically complex upper core structure of the MONJU reactor, the porous media approach was adopted for the simulation. First, a steady state solution was obtained and the transient solutions were then obtained for the turbine trip test conducted in December 1995. The time dependent inlet conditions for the mass flow rate and temperature were provided by JAEA. Good agreement with the experimental data was observed for steady state solution. The numerical solution of the transient analysis shows the formation of thermal stratification within the upper plenum of the reactor vessel during the turbine trip test. The temporal variations of temperature were predicted accurately by the present method in the initial rapid coastdown period (~300 seconds). However, transient numerical solutions show a faster thermal mixing than that observed in the experiment after the initial coastdown period. A nearly homogenization of the temperature field in the upper plenum is predicted after about 900 seconds, which is a much shorter-term thermal stratification than the experimental data indicates. This discrepancy is due to the shortcoming of the turbulence models available in the CFX-13 code for a natural convection flow with thermal stratification.

• Nuclear Engineering and Technology
• /
• v.19 no.1
• /
• pp.10-21
• /
• 1987

Uncertainty analysis of the FLB accident is performed for KNU-1 using the response surface methodology and Monte Carlo simulation. The FLB analyses using the RELAP4/Mod6 were performed a number of times to generate the data base for the uncertainty analysis, along with the EM calculation for comparison purpose. Two kinds of input sets are utilized for response surface method to investigate and compare the effects of the uncertainty of input variables on the RCS peak pressure following a FLB. The first set is composed of six major plant operational parameters and the second set is composed of five major modelling parameters. It is found through the analysis of results that the uncertainties of modelling parameters have more influence on the RCS peak pressure than the uncertainties of plant operational parameters and that the extra margin of 9% of peak pressure is gained. And one of the assumptions of EM calculation, which is usually accepted as conservative is found to be erroneous, that is, the initial core inlet temperature is found to act negatively on the RCS pressure following a FLB.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.14 no.3
• /
• pp.15-32
• /
• 2011

This study was carried out to investigate the soil characteristics and propose the management for the Monument Beobsoo Marsh, Korea. The soil properties of O.M, $Ca^{2+}$, $Na^+$ and CEC were higher and the soil properties of pH_{1:5}$ and $P_2O_5$ were lower the studied sites than other marsh sites in Korea. Although the Heavy metals such as Pb, Hg, Cd, Cu, Zn, Cr and As were lower compare to the safety standard of soil pollution in Korea, the overall conservation management plan based on long-term monitoring should be considered just because it varied by the point and non-point source pollution within the studied marsh. The source of water pollution varied due to non-point polluting origins such as sewage inlet, degraded terrain for agriculture, fishing sites, sites of removed water grasses, pesticides, chemical fertilizers, as well as fallen leaves. The creation of an artificial marsh is recommended due to the soil environment of the studied sites may be changed owing to the accumulated contaminants from the sources of both of point or non-point contaminants. The establishment of the zones of core, buffer and transition which is basic management structure of the UNESCO MaB could be applied to manage the studied site. Simultaneously the promotion of voluntary participation and education of the local residents are needed.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.1
• /
• pp.65-73
• /
• 2017

Intercoolers for multi-stage turbocharger of the hydrogen reciprocating engine for HALE UAV are installed for reducing the charged air inlet temperature of the engine. The intercooler is air to air, cross flow, plate-fin type and the fin configuration is offset-strip fin which is referenced from the heat exchanger of the ERAST. Most of HALE UAV's cruising altitude is 60,000 ft and the density of air for this altitude is very low compared to sea level. Therefore the required heat transfer area for the HALE UAV is about three-times bigger than the sea level. Consequently, it is essential to design to meet the required efficiency of intercooler in the range of not excessively growing the weight of the heat exchanger. The quasi-one dimensional heat transfer design/analysis for satisfying the requirement of the engine are written in this paper. The numerical analyses for estimating the coolant flow rate of the engine bay and pressure loss in the header and core are also summarized.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.611-617
• /
• 2008

Nowadays Plate Heat Exchanger (PHE) is widely used in different industries such as chemical, food and pharmaceutical process and refrigeration due to the efficient heat transfer performance, extreme compact design and efficient use of the construction material. In present study, discussed main conception of plate heat exchanger and applied in vacuum. PHE and aimed apply in the fresh water generator which installed in ship to desalinate seawater to fresh water use heat from engines. The experiment is proceeded to investigate the heat transfer between cold and hot fluid stream at different flow rate and supply temperature of hot fluid. Generated fresh water as outcome of the system. PHE is an important part of a condensing or evaporating system. One of common assumptions in basic heat exchanger design theory is that fluid is to be distributed uniformly at the inlet of each fluid side and throughout the core. However, in practice, flow mal-distribution is more common and can significantly reduce the heat exchanger performance. The flow and heat transfer are simulated by the k-$\varepsilon$ standard turbulence model. Moreover, the simulation contacted flow maldistribution in a PHE with 6 channels.

• Nuclear Engineering and Technology
• /
• v.20 no.2
• /
• pp.112-119
• /
• 1988

The purpose of this work is to obtain the experimental data for the forced How dryout heat flux in a heat generating stratified debris bed which simulates the degraded nuclear reactor core after severe accident. The present observations were mainly focused on the effect of coolant mass flux on the dryout heat flux in the stratified debris bed which consists of several layers with selected particle sizes under constant bed depth and temperature of inlet coolant flow conditions. The following results were obtained from this experimental work: (1) The dryout heat flux in the stratified debris bed increases with increase of upward forcing mass flux of coolant. The similar trend of increase rate of dryout heat flux in the stratified bed was observed in the uniform particle size bed. (2) For the comparison of theoretical values and experimental data, the use of surface area mean diameter as a particle diameter was suitable for the calculation of dryout heat flux.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.7 no.1
• /
• pp.94-104
• /
• 2004

The purpose of this study is to analyze various hydraulic characteristics using SMS (Surface Water Modeling System) RMA2 model. It is based on 2-D finite element method. River reaches (13.8km) from Gyeongan gauge station to the inlet of Paldang lake was selected. Finite element was made by RIMGIS Data, and the analysis of river-changes was operated by unsteady flow. The sediment concentration and bed change was simulated using SED2D model. This River's velocity was distributed that 0.05~3.85m/s and bed change was changed about 0.0003~0.0135m.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.369-369
• /
• 2016

홍수피해 저감을 위한 지하방수로나 지하저류지 등은 홍수 방어를 위한 도심 내의 토지 확보 부담을 줄이며, 집중 호우 발생 시 내수를 초기에 신속하게 배제하여 제내지 침수 피해를 줄이는데 효율적으로 활용된다. 미국 및 일본, 홍콩과 같은 외국에서는 이미 지하방수로 및 지하저류지를 활용한 홍수피해 저감방안을 수립하여 활용하고 있으며, 최근 국내에서도 치수 계획 수립 시 지하방수로 혹은 지하저류지 시설 도입이 활발히 검토되고 있으나 적용사례가 전무하여 제반기술이 부족하고 많은 시행착오가 예상된다. 제반설계기술의 경우는 구조적인 방안이 모색되어야 하며 대표적으로, 지하방수로 유입구 형상이, 동일한 흐름조건에 대한 유량배제효율에 가장 지배적인 영향인자로 알려진 바 있으며 다양한 유입구 형상설계방안이 기존 실험적 연구 및 외국 설계지침에 제안된 바 있다. 지하방수로는 접근 수로를 통해 유입된 유량이 유입구를 지나며 가속되어 와류 흐름을 형성하며 수직 갱도로 유입되는 구조를 갖기 때문에 지하방수로의 방류 효율을 높이기 위해서는 유입구에서 흐름 특성을 파악하는 것이 중요하다. 이때 유입흐름특성이 사류일 경우 혹은 급격하게 유입 유량이 많아지는 경우 수직 갱도 내에 공기 공동이 형성되어 구조물 파손, 와류의 발생으로 인한 배제효율 감소 등의 피해를 야기할 수 있으므로 수리학적으로 규명할 필요가 있다. 따라서 본 연구에서는 지하방수로의 기존 유입구형상에 대한 장단점을 비교하고, 개선점을 적용하여 수리모형을 제작하여 개수로 실험장치에 설치하고 다양한 유입흐름조건에 따라 수리실험을 수행하였다. 그 결과 유입흐름조건에 따라 발생하는 유입구의 공기 공동의 발달 및 소멸 그리고 규모변화를 정량적으로 분석하여, 유입부의 가능 단면적이 큰 수직갱도인 경우, 유량배제 효율이 감소되는 분석결과에 적절하게 일치하였으며, 본 연구결과는 향후 지하방수로 설계의 제반기술의 수립 시 효율적인 활용이 가능하다.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.1-5
• /
• 2019

In the field of combined cycle power generation, thermal barrier coating(TBC) protects the super-heat-resistant alloy, which forms the core component of the gas turbine, from high temperature exposure. As the turbine inlet temperature(TIT) increases, TBC is more important and durability performance is also important when considering maintenance cost and safety. Therefore, studies have been made on the fabrication method of TBC and super-heat-resistant alloy in order to improve the performance of the TBC. In recent years, due to excellent properties such as high temperature creep resistance and high temperature strength, turbine blade material have been replaced by a single crystal superalloy, however there is a lack of research on TBC applied to single crystal superalloy. In this study, to understand the isothermal degradation performance of the TBC applied to the single crystal superalloy, isothermal exposure test was conducted at various temperature to derive the delamination life. The growth curve of thermally grown oxide(TGO) layer was predicted to evaluate the isothermal degradation performance. Also, microstructural analysis was performed by scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS) to determine the effect of mixed oxide formation on the delamination life.