• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.569-570
• /
• 2006

In this study, the characteristics of Electrical Discharge Machining (EDM) with the electrode materials were investigated. EDM experiments have been carried out on electrodes with eight different copper-based and graphite-based materials. From the results, the copper-based electrodes showed excellent surface roughness than the graphite-based electrodes. But graphite based electrodes have advantages in economic aspects.

• 전기학회논문지
• /
• 제67권3호
• /
• pp.413-418
• /
• 2018

In this paper, we describe the development of a non-enzymatic glucose sensor based on copper nanocubes(Cu NCs) electroplated laser induced graphene(LIG) electrodes which can detect a certain range of glucose concentrations. $CO_2$ laser equipment was used to form LIG electrodes on the PI film. This fabrication method allows easy control of the LIG electrode size and shape. The Cu NCs were electrochemically deposited on the LIG electrodes to improve electron transfer rates and thus enhancing electrocatalytic reaction with glucose. The average sheet resistances before and after electroplating were $15.6{\Omega}/{\Box}$ and $19.6{\Omega}/{\Box}$, respectively, which confirmed that copper nanocubes were formed on the laser induced graphene electrodes. The prepared electrode was used to measure the current according to glucose concentration using an electrochemical method. The LIG electrodes with Cu NCs demonstrated a high degree of sensitivity ($1643.31{\mu}A/mM{\cdot}cm^2$), good stability with a linear response to glucose ranging from 0.05 mM to 1 mM concentration, and a limit of detection of 0.05 mM. In order to verify that these electrodes can be used as flexible devices, the electrodes were bent to $30^{\circ}$, $90^{\circ}$, and $180^{\circ}$ and cyclic voltammetry measurements were taken while the electrodes were bent. The measured data showed that the peak voltage was almost constant at 0.42 V and the signal was stable even in the flexed condition. Therefore, it is concluded that these electrodes can be used in flexible sensors for detecting glucose in the physiological sample like saliva, tear or sweat.

• Journal of Electrochemical Science and Technology
• /
• 제2권4호
• /
• pp.204-210
• /
• 2011

Thin film electrodes have been intensively studied for active materials and current collectors to enhance the electrochemical performance. Here, porous structures of nickel-based oxide films, consisting of nickel oxide and copper (II) oxide, which was derived from the copper substrate during the annealing process, were deposited on metallic copper foils. The half-cell tests revealed excellent capacity retention after $80^{th}$ charge/discharge cycles. Some films showed an excess of the theoretical capacity of nickel oxides, which mainly originate from partially oxidized copper substrates during annealing. These results exhibit that both a preparation method of an active materials and partially oxidized current collectors could be important roles to apply thin film electrodes.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권9호
• /
• pp.443-448
• /
• 2006

Non-contacting capacitive sensor based on Thompson-Lampard theorem have been fabricated and characterized for measuring of 때 order displacements. To overcome disadvantages of the existed capacitive sensors of parallel plate type with 2-electrodes and 3-electrodes, the developed new sensor was designed to have 4-electrodes with a constant gap of 0.2mm between the electrodes. Two of the electrodes were used as a high potential electrode and a low one, the other two electrodes were used as guard electrodes. These electrodes were made from copper using RF sputtering system on a sapphire plate with diameter 17 mm and thickness 0.7 mm. This sensor can be used for measuring the distance not only between the sensor and metallic target connected to ground potential but also non-metallic target without ground connection.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1466-1468
• /
• 2009

The preparation method of copper nanopowder by dry process for conductive ink was investigated. Inert gas condensation method was used to synthesize copper nanopowder. The produced powders was spherical and sized 10~100nm flowing the conditions. The results showed that input voltage and evaporation rate is critical variables for nano-sized copper powder.

• 한국수소및신에너지학회논문집
• /
• 제3권2호
• /
• pp.9-15
• /
• 1992

Electroless copper plating method using an alkaline bath have been employed in copper coating of the (LM)Ni4.5Co0.1MnO.2A10.2 hydrogen storage alloy powders for electrode preparation. The plating were conducted without any pretreatment of alloy powders. For the preparation of the electrodes, about 0.12g of the copper coated alloy powder (copper to alloy ratio 1/3 by weight) was compacted with pressure of 6 tons/cm2 at room temperature. The disk-type compacts had a diameter of 10mm and thickness of about 0.24mm. The electrode characteristics were examined through SEM observations and electrochemical measurements in a half cell. The electrochemical measurement showed that the maximum discharge capacity of the electrodes prepared by using alkaline bath were 245mAh per gram of coated alloy (327mAh per gram of alloy) and appeared a considerable degradation with increasing number of cycles. The decrease of the discharge capacity after 100 cycles was about 30% It can be suggested that, with a slight of improvement, this electroless copper plating method could be applied to the preparation of the rare earth-nickel based alloy electrode.

• 마이크로전자및패키징학회지
• /
• 제30권4호
• /
• pp.17-31
• /
• 2023

세계적으로 화석 연료의 무분별한 사용으로 지구 온난화가 가속화되면서 대기 중 이산화탄소 농도를 줄이기 위한 다양한 노력이 진행되고 있다. 전기화학적 이산화탄소 환원 기술은 이산화탄소를 유용한 탄화수소 화합물로 전환할 수 있는 친환경 기술로 인정받고 있는 유망한 기술로 탄소중립을 달성하기 위해 필수적이라는 의견이 지배적이다. 이산화탄소 환원 전극으로 사용되는 많은 물질 중에서도 구리는 C₂₊ 화합물을 생성할 수 있는 유일한 금속으로 알려져 있으나 낮은 전환 효율과 선택도로 인해 아직 상용화되기에는 어려움이 있어 이를 해결하기 위해 다양한 연구가 이루어지고 있다. 본 리뷰에서는 구리 기반 전극을 활용한 다양한 이산화탄소 환원 연구들을 소개한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.747-751
• /
• 2006

The hydrogenated amorphous silicon thin film transistor (a-Si:H TFT) with copper as source and drain electrode has been fabricated to obtain its transfer characteristics and stressed with positive and negative bias to investigate the instability variation comparing to conventional MoW-Al based TFT device. The results show that there is no copper diffusion into active layer of a-Si:H TFT, even during the thermal process. In addition, a 15-inch XGA a Si:H TFT LCD display utilizing Cu as gate electrodes has been developed.

• Bulletin of the Korean Chemical Society
• /
• 제34권3호
• /
• pp.801-809
• /
• 2013

We investigate sensitivity and limit of detection (LOD) of trace copper (Cu) metal using pristine carbon nanotube (CNT) and acidified CNT (ACNT) electrodes. Squarewave based anodic stripping voltammetry (SWASV) is used to determine the stripped Cu concentration. Prior to performing the SWASV measurements, its optimal conditions are determined and with that, effects of potential scan rate and $Cu^{2+}$ concentration on stripping current are evaluated. The measurements indicate that (1) ACNT electrode shows better results than CNT electrode and (2) stripping is controlled by surface reaction. In the given $Cu^{2+}$ concentration range of 25-150 ppb, peak stripping current has linearity with $Cu^{2+}$ concentration. Quantitatively, sensitivity and LOD of Cu in ACNT electrode are 9.36 ${\mu}A\;{\mu}M^{-1}$ and 3 ppb, while their values are 3.99 ${\mu}A\;{\mu}M^{-1}$ and 3 ppb with CNT electrode. We evaluate the effect of three different water solutions (deionized water, tap water and river water) on stripping current and the confirm types of water don't affect the sensitivity of Cu. It turns out by optical inspection and cyclic voltammetry that superiority of ACNT electrode to CNT electrode is attributed to exfoliation of CNT bundles and improved interfacial adhesion occurring during oxidation of CNTs.

• 마이크로전자및패키징학회지
• /
• 제30권2호
• /
• pp.21-32
• /
• 2023

구리 나노와이어(CuNW)는 전기 전도도가 우수할 뿐만 아니라 높은 기계적 유연성과 비용 효율성 등의 장점이 있다. 그러나 구리 나노와이어는 산화가 쉽게 일어나기 때문에 투명 전극의 특성까지도 저하될 수 있다는 단점 또한 존재한다. 따라서, 이러한 문제점을 해결하기 위한 연구들이 진행되고 있다. 이에 본 고에서는 탄소 기반 물질, 금속, 전도성 고분자 등의 코팅용 소재를 활용하여 구리 나노와이어 투명전극의 산화를 방지하고 안정성을 향상시키기 위한 다양한 방법과 연구를 소개한다. 이를 통해 구리 나노와이어 기반 기술의 발전과 산화에 대한 문제를 해결할 수 있는 방안들을 제공하고자 한다.