• Membrane and Water Treatment
• /
• 제11권3호
• /
• pp.201-206
• /
• 2020

Electrodialysis (ED) is used in wastewater treatment, during the processing and recovery of beneficial materials, to produce usable water. In this study, sulfate and chlorine ions, which are the anions majorly used for electroplating, were studied as factors affecting the recovery of copper, nickel and water from wastewater by electrodialysis. Although the removal rates of copper and nickel ions were slightly higher with the use of chlorine ions than of sulfate ions, the removal efficiencies were above 99.9% under all experimental conditions. The metal ions of the plating wastewater flowed through the ion exchange membrane of the diluate tank and the concentrate tank while all the water moved together due to electro-osmosis. The migration of water from the diluate tank to the concentrate tank was higher in the presence of a monovalent chloride ion compared to that of a divalent sulfate ion. When sulfate was the anion used, the recoveries of copper and nickel increased by about 25% and 30%, respectively, as compared to the chloride ion. Therefore, when divalent ions such as sulfate are present in the electrodialysis, it is possible to reduce the movement amount of water and highly concentrate the copper and nickel in the plating wastewater.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.820-832
• /
• 2001

In order to obtain the basic data on the optimum conditions of electroforming process for fabricating the micro wiring pattern for plate type micro- motor core, characteristics of plating bath and properties of deposits were studied with various copper plating baths which contain sulfate, fluoborate, pyrophosphate and cyanide salt, respectively. Cathodic polarization, throwing power, internal stress, texture and surface morphology of deposits were observed. Throwing power of plating solution is deeply related to the polarization curves and the values are in the range of +20∼20%. The order of values ate as follows- pyrophosphate, cyanide, sulfate and fluoborate bath. Internal stresses of deposits are tensile in all of the copper plating bath. Thickness of the deposits plated at the center of holes has the highest value in the pyrophosphate bath and K factor, ratio of height and width of deposit, is 1.44. It was confirmed that the pyrophosphate bath was the best one for the electroforming of wire pattern.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.153-153
• /
• 2009

첨가제를 사용한 피로인산구리 도금욕에서 마그네슘 합금상에 직접 구리도금을 실시하였다. 피로인산구리 도금욕에서 첨가제가 마그네슘 합금 도재에 미치는 영향에 대하여 연구하였다. 연구에 따른 첨가제를 포함하는 피로인산구리 도금욕에서 구리도금층의 적합성을 확인하기 위하여 기존의 마그네슘 모재에 구리를 도금하기 위한 방법인 징케이트 처리 후 시안구리도금욕에서 구리도금하는 방법과 비교 고찰 하였다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1994년도 추계 총회 및 학술발표회
• /
• pp.8-11
• /
• 1994

Disposal of hazardous ions in the aqueous streams is a significant industrial waste problem.. Waste streams from electronics, electroplating, and photographic industries contain metal ions such as copper, nickel, zinc, chromium(IV), cadmium, aluminum, silver, and gold, amongst others in various aqueous solutions such as sulfates, chlorides, fluorocarbons, and cyanides. Typical plating solutions having similar compositions are listed in Table 1. Spent process streams in catalyst manufacturing facilities also contain precious metals such as Ag, Pt, and Pd. Developing an effective recovery process of these metal ions for reuse is important.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.158-163
• /
• 2021

Some studies on electrochemical additive manufacturing of metals were summarized in this technical report, and development status of selective electrochemical 3D printing technology was introduced. In order to apply it to the PCB mass production process, essential considerations how to overcome the fundamental problems, such as the sizing, process sequence and PCB process design have been described.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.151.1-151.1
• /
• 2017

This work studied the corrosion behavior of AZ31 Mg alloy galvanically coupled with Cu during immersion in 0.1 and 0.5 M NaCl solutions by in-situ observation and galvanic corrosion current measurement using a zero resistance ammeter. The corrosion behavior of AZ31 Mg alloy was also studied by salt spray test. The average galvanic corrosion density during 2 h immersion in 0.1 NaCl solution was found to decrease as an exponential function with increasing the surface area ratios between AZ31:Cu or with increasing the distance between AZ31 and Cu. The corrosion of electrodeposited Cu on AZ31 Mg alloy was concentrated at the area next to Cu (about 5 mm for immersion test and 2 mm for salt spray test) and pitting corrosion was accelerated at the area beyond the severely corroded area by the galvanic coupling effect.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 G
• /
• pp.3295-3297
• /
• 1999

This paper presents the fabrication of an electromagnetic micro actuator consisting of a Parylene diaphragm with a spiral copper coil and a permanent magnet. The copper coil is fabricated by electroplating and patterning. The frequency response of the actuator are obtained using a laser vibrometer. When the input voltage is 3 V, the DC deflection is 5 ${\mu}m$, and the resonance frequency is about 35 Hz. Also, the mechanical sensitivity of the actuator diaphragm is 69 ${\mu}m/V$.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.372-376
• /
• 1999

The deposited Cu film on the ferrite magnet was more deposited comparing with that on the plastic magnet. The Cu film became thicker on the S pole comparing with that on the N pole in the both of magnets. The thickness and texture coefficient of deposited copper film affected with direction of line of magnetic force. The difference of pole had little or no effect to the texture coefficient of deposited nickel film. The reaction rate on ferrite magnet and S pole was faster comparing with that on plastic magnet and N pole.

• 대한기계학회논문집B
• /
• 제35권7호
• /
• pp.701-708
• /
• 2011

기울어진 평판에서 발생하는 자연대류 열전달현상을 $R_{a_L}$ $1.69{\times}10^{11}$과 $7.23{\times}10^{12}$에 대하여 실험적으로 연구하였다. 유사성을 이용하여 열전달실험을 물질전달 실험으로 대체하였고 물질전달계로 전기도금계를 사용하였다. 평판의 기울기는 상향수평에서 하향수평까지 $10^{\circ}$씩 변화시켰다. 하향평판에서는 수직 벽면에 대한 자연대류 열전달 상관식에서 g 대신 g $cos{\theta}$로 대체함으로써 열전달계수를 구할 수 있다는 기존의 이론과 일치하는 결과를 얻었다. 상향평판의 경우 경계층이 벽면을 따라 발달되는 경우와 벽면으로부터 박리되는 2가지 영역으로 구분되는데 박리에 따른 열전달 증가를 확인하였다. 아울러 도금패턴을 이용하여 박리지점을 시각화하였고 박리지점에 대한 분석이 수행되었다.

• Journal of Electrochemical Science and Technology
• /
• 제7권2호
• /
• pp.132-138
• /
• 2016

In this study, we report the fabrication of functional complex fibers, which have been studied widely globally for numerous applications. Here, we fabricated conductive complex fibers with antibacterial properties by coating metal ions on the surface of plastic (polypropylene) fibers using the electroless and electrochemical deposition. First, we polished the polypropylene melt-blown fiber surface and obtained an absorbing Pd seed layer on its surface. Subsequently, we substituted the Pd with Cu. Bis-3-sulfopropyl-disulfide disodium salt (SPS), polyethylene glycol (PEG), and ethylene thiourea (ETU) were used as the brightener, carrier, and leveler, respectively for the electroplating. We focused on most achieving the stable plating condition to remove dendrites, which are normally during electroplating metals so that smooth layer is formed on the fiber surface. The higher the amount of SPS, the higher was the extent of irregular plate-like growth. Many irregularities in the form of round spheres were observed with increase in the amount of PEG and ETU. Hence, when the additives were used separately, a uniform coating could not be obtained. A stable coating was obtained when the three additives were combined and a uniform 5-9 μm thick copper layer with a stable morphology could be obtained around the fiber. We believe that our results can be applied widely to obtain conductive fibers with antibacterial properties and are useful in aiding research on conductive lightweight composite fibers for application in information technology and robotics.