• 한국전기전자재료학회논문지
• /
• 제18권5호
• /
• pp.468-472
• /
• 2005

High-temperature Superconductor(HTS) tubes were fabricated in term of different processing variables such as preheating temperature, speed of mold rotation and cooling rate by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050{\circ}C{\sim}1100{\circ}C\;and\;550{\circ}C\;for\;30\; min$, respectively The mould roating speed was 1000 rpm. A tube was annealed at $840 {\circ}C$ for 72 hours in oxygen atmosphere. The plate-like grains were well developed along the loafing direction and typical grain size was about more than $40{\mu}$. It was found that Ic values increased with increasing the Preheating temperature and speed of mold rotation. While Ic decreased with increasing the cooling rate. The measured Ic in $50mm{\times}70mm{\times}2.5mm$ tube was about 896 Amp.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.115-116
• /
• 2002

This study was carried out as one of efforts to overcome difficulties in air bearing design due to low stiffness and low damping. Hydrodynamic effects on hydrodynamic stiffness of a fluid film in a high speed air bearing with tow-row air sources are investigated. The hydrodynamic effects by the high speed over DN 1,000,000 and eccentricity of a proceeding which are not considered in conventional design of an air bearing need to be reconsidered. The hydrodynamic effects, which dominantly influence on the load capacity of air bearing, are caused mainly by proceeding speed, eccentricity, and the source positions. The two-row source arrangement in the air bearing produces quite unique hydrodynamic effects with respect to pressure distribution of the air film. Optimal arrangement of the two-row sources improves performance of an air bearing in film reaction force and loading capacity of high speed spindles. This study compares the pressure distribution by numerical simulation as a function of eccentricity of proceeding and the source positions. The air source position 1/7L form one end of an air bearing was found to be superior to source position of 1/4L. The dynamic stiffness were obtained using a two-dimensional cutting method which can directly measure the cutting reaction forces and the displacements of the spindle in two directions using a tool dynamometer and transducer sensors. Heat generation in the air film can not be negligible over the speed of DN 2,000,000. In order to analysis effects of heat generation on the characteristics of air bearing, high cooling bearing spindle and low cooling bearing spindle were tested and compared. Characteristics of the frequency response of shaft and motion of run out errors were different for the spindle. The test results show that, in the case of low cooling bearing spindle, the stiffness became smaller due to heat generation. The results, which were obtained for high speed region, may be used as a design information for spindle which can be applied to precision devices such as ultra precision grinding and ultra high speed milling.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1418-1423
• /
• 2004

High speed machining experiment on the heat-treated mold steel(STAVAX and CALMAX of hardness HRc 53) is carried using TiAlN coated ball endmill. Tool life and wear characteristics under the various machining parameters and cooling methods are investigated. Effect of cooling method on life and wear of the tool was compared. For most cases, tool life was not determined by the amount of wear but by th chipping on the cutting edge. It is found that tool manufacturer's cutting parameters generally agrees with the results of this experiment.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1150-1155
• /
• 1992

본 연구에서는 제철소 열연공정의 냉각효율 개선을 위한 기초연구로 수행되었 다. 전열면의 초기온도가 900.deg. C이상일 때 층류 냉각방식에 의한 고온강판의 냉각특 성에 영향을 주는 모든 인자를 엄밀히 고려하는 것은 매우 어려운 일이다.따라서 본 연구에서는 노즐과 고온면 사이 거리(L), 유량(Q), 냉각 초기온도 등을 실제 작업 조건에 가깝게 변화시켜 가면서 수냉반경의 변화를 중심으로 전열면의 냉각 특성을 해 석하였다.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.126-131
• /
• 2009

A $CO_2$ heat pump system was designed for both cooling and heating in the cabin of electric vehicles, hybrid vehicles or fuel cell vehicles, In this study, the performance characteristics of the heat pump system without any supplementary heating device were analyzed and the heating performance was compared with the cooling performance for various operating conditions. Experiments were carried out by changing the speed of electric drive compressor, the air flow rate of interior heat exchanger and the air inlet temperature and speed of exterior heat exchanger. Therefore, the cooling/heating capacities and the corresponding COPs are quantified. Also, the heat pump system showed an improved performance for the cooling operation and the heating operation. In this study, the experimental results can be used to evaluate the effect of system design changes on system performance as well as the development of a highly efficient heat pump system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 Handout for 2000 Inter. Machine Tool Technical Seminar
• /
• pp.109-115
• /
• 2000

The spindle unit is core parts in high precision machine tools. Diverse static, dynamic and thermal charateristics of spindle unit are needed for special purpose of machine tools. Compromise between those charateristics will be done in concept design phase. High static stiffness at spindle nose may be very important performance for heavy cutting work. High dynamic stiffness is also useful to high precision and high speed machine tools. Improvement of thermal charateristics in spindle lead to high reliability of positioning accuracy. For high speed spindle structure, the design parameter such as, bearing span, diameter, bearing type and arrangement, preload, cooling and lubrication method should be in harmony.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.50-53
• /
• 2008

It's so difficult to obtain simultaneously both product quality and improvement of the productivity of which products are in hot aluminum extrusion process. But significant improvements in productivity and extrudate quality result from die cooling system using nitrogen gas injection during aluminum hot extrusion. These benefits are due primarily to cooling effect nitrogen gas and removal of excess heat in the extrudate temperature. This investigation is carried out hot extrusion experiment, also compared cooling system with non-cooling system to inspect cooling effects on hot aluminum extrusion. The purpose of this investigation is estimated the grain growth fur the extrudate quality, and the ram speed for the improvement of the productivity.

• 항공우주시스템공학회지
• /
• 제12권4호
• /
• pp.90-97
• /
• 2018

고속 비행체의 연료공급 및 냉각계통의 통합설계를 위한 프로그램을 개발하고 이를 이용하여 예비설계 및 검증을 수행하였다. 개발된 설계 도구는 상용 열유체 시스템 설계 프로그램을 프레임워크로 이용하여 모듈 통합과 입출력 처리 등이 개선되었다. 모델의 형상 및 열환경 변수를 입력하여 구성품의 상태량을 계산하고 모사를 통하여 설계 요구조건 충족을 확인할 수 있다. 이 프로그램을 사용하여 시스템의 세부 구성품 규격 선정에 적절하게 사용할 수 있음을 나타내었다.

• 한국추진공학회지
• /
• 제18권1호
• /
• pp.97-104
• /
• 2014

고속 비행체에 연료를 공급하고, 내/외부의 열부하를 처리하기 위한 연료공급 및 냉각계통의 예비 열설계를 수행하였다. 이를 위해 임의의 임무형상에 대한 해석모델을 구성하고 성능해석을 진행하였다. 산출된 연료소모율과 내부의 유동 상태량을 이용하여 시스템의 각부 경계조건에 대한 열부하량을 계산하고 검증하였다. 이를 연료의 흡열반응을 이용한 시스템의 냉각성능과 비교하여 설계 요구조건을 충족시키는 것을 확인하였다.

• 한국농림기상학회지
• /
• 제3권4호
• /
• pp.206-214
• /
• 2001

본 연구는 경상남도 하동군 하동읍 화심리의 배 과수원에서 주변 지형 특성 및 해발고도별 서리 피해 상습지의 봄철 야간 냉각률, 특정일의 야간기상분포를 구명하고자 수행하였다. 냉각률은 평지에서 3, 4월이 가장 높아 0.7$^{\circ}C$/hr, 9월에 가장 낮아 0.3$^{\circ}C$/hr 정도로 0.4$^{\circ}C$/hr의 차이를 보였다. 일몰 후부터 일출 전까지의 야간기온 냉각률과 유효야간복사의 상관은 r=0.63$^{**}$ 였고, 풍속이 0.5 m/sec 이하에서 야간유효복사와 냉각률은 r=0.90$^{**}$ 으로 상관이 높았으며, 풍속이 강해지면서 냉각률과 상관관계는 낮아졌다. 맑았던 날의 냉각률은 평지(site 1,2,3), 경사면(site 4,5), 산 정상(site 6)에서 각각 시간당 약 1.4$^{\circ}C$, 1.2$^{\circ}C$, 0.6$^{\circ}C$ 하강하여 산 정상으로 갈수록 냉각률이 작아졌다. 맑고 평균풍속이 1.2~2 m/sec이며 산 정상이 경사면이나 평지보다 기온이 낮을 때, 2200~2300경에 경사면(site 4,5)에서의 기온은 떨어지는 것이 아니라 오히려 상승하였다.