• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.3
• /
• pp.206-214
• /
• 1999

The effect of cooling rate on carbide precipitation during quenching of austenitic manganese steel was investigated by optical microscopy, image analyzer and numerical analysis. A computer program based on the finite difference method for analyzing heat treatment processes was developed in order to evaluate cooling rates and the possibility of carbide precipitation during quenching. The area ratio of carbide precipitated in the austenite matrix was measured by the image analyzer, and used to determine the critical point of carbide precipitation. Temperature-dependent critical cooling rates at the critical points were calculated using the present simulation program, The calculated results showed a good agreement with the experimental ones.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.1
• /
• pp.25-31
• /
• 2009

Supercooled type ice storage system with aqueous solution (or water) may have trouble with non-uniform release of supercooling even though it contributes to the simplicity of system and ecological improvement. The non-uniform release increases the instability of the system because it may cause an ice blockage in pipe or cooling part. In order to suppress the release of the supercooling, a cooling experiment was tried to an ethylene glycol(EG) 3 mass% solution corresponding with pressurization. Also, the frequency ratio of the release of the supercooling was measured to the pressurization from 101 to 505 kPa. At results, the frequency ratio of supercooling release tends to decrease as the pressure of the aqueous solution increased in each cooling rate. Moreover, it tends to decrease as the cooling rate of the solution decreased in each pressure.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.4 no.4
• /
• pp.263-276
• /
• 1992

The transmission current in a power cable is determined under the condition of separate pipe cooling. To this end, the thermal analysis is conducted with the standard condition of separate pipe cooling system, which constitutes one of the underground power transmission system. The changes of transmission current in a power cable with respect to the variation of temperatures and flow rates of inlet cooling water as well as the cooling spans are also determined. As a consequnce, the corresponding transmission current is shown to vary within allowable limit, resulting in the linear variation of the current for most of the cable routes. The abrupt changes of current, however, for the given flow rate of inlet cooling water in some cooling span lead to the adverse effects on the smooth current transmission within the underground power transmission system. In practice, it is expected that the desinging of the separate pipe cooling system in conjunction with the evaluation of system capacity should take into account the effects of design condition on the inlet cooling flow rate.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.3
• /
• pp.149-156
• /
• 2009

A small-scale thermoelectric cooling system was built in an effort to enhance the performance of the refrigeration system by utilizing the water-cooled jacket which was attached to the hot side of the thermoelectric module. Considered design parameters for the water-cooled jacket were the geometry of the flow passage inside the jacket and the flow rate of cooling water. The higher flow rate of cooling water in the jacket resulted in a better performance of the refrigeration system. The increase in the number of channels for water flow passage inside the cooling jacket also showed significant improvement on the performance of the thermoelectric cooling system such as the cooling capacity and the COP of the refrigeration system.

• Korean Journal of Animal Reproduction
• /
• v.11 no.3
• /
• pp.161-169
• /
• 1987

This experiment was carried out to investigate the optimal cooling rate and the plunging temperature into liquid nitrogen of the 8-cell hamster embryos. The female hamsters were induced to superovulate by intraperitoneal injection of 30 i.u. PMSG. Embryos were flushed from oviduct and uterine horn. Embryos were frozen and incubated with a modified Dulbecco's phosphate buffered saline, and equilibrated with 1.5M-dimethyl sulfoxide by a 3-step procedure. The cooling rate of samples was 1$^{\circ}C$/min from room temperature to -5$^{\circ}C$ and the samples were seeded at -5$^{\circ}C$. The plunging temperatures into liquid nitrogen were -20, -25, -30, -35, -40, -45, -50 and -55$^{\circ}C$ at 0.3$^{\circ}C$/min, 0.5$^{\circ}C$/min and 1$^{\circ}C$/min cooling rates, respectively. This mean numbers of ovulation points and recovered embryos were 59.4 and 48.4 appearing 81.6% recovery rate. The percentage of 8-cell embryos in recovered embryos was 68.2. The survival rates of embryos plunged at -45$^{\circ}C$ were 73.5% at 0.3$^{\circ}C$/min, 44.8% at 0.5$^{\circ}C$/min and 30.3% at 1$^{\circ}C$/min cooling rates, respectively. This mean numbers of ovulation points and recovered embryos were 59.4 and 48.4 appearing 81.6% recovery rate. The percentage of 8-cell embryos in recovered embryos was 68.2. The survival rates of embryos plunged at -45$^{\circ}C$ were 73.5% at 0.3$^{\circ}C$/min, 44.8% at 0.5$^{\circ}C$/min and 30.3% at 1$^{\circ}C$/min cooling rates, respectively. The survival rates at 0.3$^{\circ}C$/min were significantly high. Under the condition of 0.3$^{\circ}C$/min cooling rate, the survival rates of embryos according to the plunging temperature were 70.0% and 73.5% at -40 and -45$^{\circ}C$, and those were higher than other plunging temperatures. Under the condition of 0.5$^{\circ}C$/min and 1$^{\circ}C$/min cooling rates, the survival rates according to the plunging temperatures were lower than the cooling rate of 0.3$^{\circ}C$/min, showing the similar tendency at all the plunging temperatures. In conclusion, 8-cell hamster embryos showed the best survival rates at 0.3$^{\circ}C$/min cooling rate and -45$^{\circ}C$ plunging temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.155-158
• /
• 2003

The effects of Mn, V addition on the behavior of structure and the effects of cooling rate of S20C steel for use of Tn housing and valve for automotive parts have been investigated. Transformation start temperature measured from inflection point of cooling curves has been found out to decrease with increasing cooling rate and to be more sensitive to Mn contents when cooling rate is fast. It was therefore shown that the grain was refined. If there is a big compacting pressure, it is indicated that hardness becomes much greater at surface than inside.

• Journal of Korea Foundry Society
• /
• v.8 no.3
• /
• pp.271-281
• /
• 1988

Al-bronze has a good mechanical property, corrosion resistance and castability, so being highlighted for the new copper alloy. So, effects of alloy composition and cooling rate in the mechaincal properties and solidification behavior have been investigated. The results obtained are as follows; 1) Change in volume on solidification is larger in metal mold casting than in sand mold casting. And it decreases by the addition of Al. 2) The mechanical property in metal mold casting is superior to the one in sand mold casting, and the inclination is obvious up to 9% Al, after heat-treatment ($885^{\circ}C$, $1.5hrs\;{\rightarrow}\;W\;{\cdot}\;Q\;{\rightarrow}\;540^{\circ}C$, 3hrs) 3) By adding Al, the mechanical property is slightly increased up to 9% Al, Above 9% Al, it is increased rapidly, and is accelerated by adding Fe. 4) Cooling rate and hardness, and grain size and cooling rate are related as follows in the range of $1100^{\circ}C$ to $1200^{\circ}C$ pouring temperature. Grain size(${\mu}m$)=$929.6422{\times}cooling\;rate(^{\circ}C\;/\;sec)^{-0.51537}$ Hardness(BHN)=$765.45713{\times}grain\;size({\mu}m)^{-0.31058}$.

• Journal of Korea Foundry Society
• /
• v.10 no.3
• /
• pp.219-224
• /
• 1990

In this, we have investigated the solute behavior in front of solid-liquid interface according to the change of the cooling rate in bronze alloy and phosphor bronze alloy. The conclusive summary is as follows: 1) The secondary dendrite arm spacing was decreased with increasing the cooling rate. 2) The minimum solute concentration happened to along centerline of primary arm, and the maximum solute concentration was found at the boundary of arm or between the arms the minimum solute concentration was increased with the cooling rate. 3) Segregation Index S was decreased with increasing the cooling rate and content of P. 4) The degree of the microsegregation was decreased with increasing the cooling rate. The effective distribution coefficient, Ke was increased with addition of P in Cu-Sn.

• Journal of Korea Foundry Society
• /
• v.19 no.1
• /
• pp.54-65
• /
• 1999

The present work is an attempt to evaluate the relationship between dendrite arm spacing and average cooling rate in gasatomized $Al_{87.3}misch$ $metal_{8.3}Ni_{4.4}$ powder by means of the following methods. One is calculation of heat transfer coefficient and average cooling rate, which are derived from estimated particle velocity during gas-atomization. The other is measurement of secondary dendrite arm spacing, which are observed on the particle surface. Then, we make experimental equation for this relationship in case of permanent mold casting and compare it with similar equation in case of rapidly solidified powder. Both average cooling rates and solidification rates are considered to represent the variance of dendrite arm spacings in two types soidification route. Even though there is a considerable difference in each average cooling rate, the dendrite arm spacing values are similar in two cases; particle diameter, $100\;{\mu}m$, and casting width, 2.05 mm. It is because that each solidification route has similar solidification rate.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.1 s.24
• /
• pp.117-124
• /
• 2006

Experiments on film cooling were performed with a small scale rocket engine homing liquid oxygen (LOx) and Jet A-1(jet engine fuel). Film coolants(Jet A-1 and water) were injected through the film cooling injector. Film cooled length and the outside wall temperature of the combustor were determined for chamber pressure, and the different geometries(injection angle) with the flow rates of film coolant. The loss of characteristic velocity due to film cooling was determined for the case of film cooling with water and Jet A-1. As the coolant flow increases, the outside wall temperatures decrease but the decrease in the outside wall temperatures reduced over the 8 percent film coolant flow rate. The efficiency of characteristic velocity was decreased with the Increase of the film coolant flow rate.