• 신재생에너지
• /
• 제1권4호
• /
• pp.49-54
• /
• 2005

There is close relation between the heat generation in the fuel cell stack and the fuel performance. In PEM fuel cell vehicles, the stack coolant temperature is about $65^{\circ}C$, which is far lower than that for general automobile engine. Therefore, it is hard to release heat generated in the stack by using a radiator of limited size because of the reduced temperature difference between the coolant and the ambient air. In this study, indirect stack cooling system using $CO_2$ heat pump was designed and its stack cooling performance in releasing heat to the ambient was investigated. This work focuses on a series of processes that grasp the relation among the fuel cell power, the radiator capacity and the stack temperature. The purpose of this work is to find out a way to properly release sufficient amount of heat through the finite sized radiator, so that the slack power generation can not be deteriorated due to the stack temperature increase. The optimization between the compressor power consumption and the fuel cell output power can be carried out to maximize the performance of fuel cell system.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(1)
• /
• pp.404-410
• /
• 1998

In Yonggwang nuclear units 3 and 4 currently under commercial operation, the cold leg temperature was very close to the technical specification limit of 298$^{\circ}C$ during initial startup testing, which was caused by the higher-than-expected reactor coolant system flow. Accordingly, the reference temperature (Tref) program needed to be revised to allow more flexibility for plant operations. In this study, the method of a specific test performed at Yonggwang nuclear unit 4 to revise the Tref program was described and the test results were discussed. In addition, the modified Tref program was evaluated on its potential impacts on system performance and safety. The methods of changing the Tref program and the associated pressurizer level setpoint program were also explained. Finally, for Ulchin nuclear unit 3 and 4 currently under initial startup testing, the effects of reactor coolant system flow rate on the coolant temperature were evaluated from the thermal hydraulic standpoint and an optimum Tref program was recommended.

• Nuclear Engineering and Technology
• /
• 제50권8호
• /
• pp.1306-1313
• /
• 2018

The randomness and incipient nature of certain faults in reactor systems warrant a robust and dynamic detection mechanism. Existing models and methods for fault diagnosis using different mathematical/statistical inferences lack incipient and novel faults detection capability. To this end, we propose a fault diagnosis method that utilizes the flexibility of data-driven Support Vector Machine (SVM) for component-level fault diagnosis. The technique integrates separately-built, separately-trained, specialized SVM modules capable of component-level fault diagnosis into a coherent intelligent system, with each SVM module monitoring sub-units of the reactor coolant system. To evaluate the model, marginal faults selected from the failure mode and effect analysis (FMEA) are simulated in the steam generator and pressure boundary of the Chinese CNP300 PWR (Qinshan I NPP) reactor coolant system, using a best-estimate thermal-hydraulic code, RELAP5/SCDAP Mod4.0. Multiclass SVM model is trained with component level parameters that represent the steady state and selected faults in the components. For optimization purposes, we considered and compared the performances of different multiclass models in MATLAB, using different coding matrices, as well as different kernel functions on the representative data derived from the simulation of Qinshan I NPP. An optimum predictive model - the Error Correcting Output Code (ECOC) with TenaryComplete coding matrix - was obtained from experiments, and utilized to diagnose the incipient faults. Some of the important diagnostic results and heuristic model evaluation methods are presented in this paper.

• 한국추진공학회지
• /
• 제21권2호
• /
• pp.48-59
• /
• 2017

본 연구에서는 수치모사를 통해 탄의 사출관 내부의 열 유체역학적 분석과 탄의 운동성능 해석을 수행하였다. 동적 격자(dynamic grid)를 사용한 해석영역에서 계산이 진행되었고 증발이 완료된 물을 냉각제로 사용하였다. 고온의 공기와 냉각제간의 상호작용 및 유동장을 해석하기 위해, Realizable $k-{\varepsilon}$ 난류 모델과 VOF (Volume Of Fluid) 모델을 선정하고 냉각제 유량변이에 따른 수치 해석을 진행하였다. 해석결과, 사출관의 압력은 냉각제의 유무에 따라 큰 차이를 보였고, 냉각제량에 따라서도 각각의 차이를 보였다. 탄의 속도와 가속도의 변이는 압력에 종속하여 나타났다.

• Nuclear Engineering and Technology
• /
• 제17권4호
• /
• pp.256-266
• /
• 1985

냉각재 유량상실 사고가 가압경수형 원자로인 고리 1호기에 대하여 해석되었다. 냉각재 유량 상실 사고는 그 심각도에 따라 다음과 같이 3가지로 분류된다. 즉, 일부 유량 상실사고, 완전 유량 상실 사고, 그리고 펌프 축 고착 사고이다. 사고 해석은 계통 과도 현상 및 평균 노심분석, DNBR 계산, 그리고 고온점 분석의 3단계로 수행된다. 원자로 계통과도 현상 코드인 KTRAN이 본 사고를 빠른 시간에 모사할 수 있도록 개발되었다. DNBR계산을 위해서는 열수력학 코드인 SCAN및 COBRA IV-I가 채택되었으며, 고온점 분석을 위해서는 연료봉 과도 현상 코드인 LTRAN이 쓰였다. 이러한 전산코드 시스템은 과도 현상 해석에 빨리 응답하여야 한다. 왜냐하면 사고가 발생한 후 수 초안에 심각한 상태에 이르기 때문이다. 불행히도 KTRAN코드에 의하여 이러한 목적은 충족되지 않았다. 그러나 다른 계통 해석 코드에 비하여 잔은 계산 시간에도 불구하고 KTRAN에 의한 계산 결과는 FSAR의 결과와 전반적으로 잘 일치함으로써 KTRAN코드가 사고 해석에 유용함이 밝혀졌다.

• 한국산학기술학회논문지
• /
• 제16권6호
• /
• pp.3708-3713
• /
• 2015

본 연구의 목적은 연료전지 자동차의 스택 시스템의 열적 특성을 파악하기 위하여 상용 수치 해석 프로그램을 이용하여 열전달 성능을 해석적으로 고찰하였다. 이를 위하여 연료전지 자동차가 일반도로 및 등판도로 등 주행 특성에 따른 스택 열관리 시스템의 냉각 특성과 에어컨의 작동 여부 등 운전 특성에 따른 스택 열관리 시스템의 냉각 특성을 고찰하였다. 스택 라디에이터로 유입되는 공기 유속이 증가함에 따라 모든 냉각수 유량조건에서 열전달 성능은 향상되었다. 공기 유속이 2 m/s에서 10 m/s로 증가함에 따라 스택 라디에이터의 열전달 성능은 냉각수 유량 20 l/min에서 105.3% 증가하였고, 냉각수 유량 120 l/min에서 221.3% 증가하였다. 스택 라디에이터는 가혹조건인 등판 각도 8% 및 속도 50 km/h에서 냉각수 입구 온도차 $9.45^{\circ}C$로 일반조건인 등판 각도 0% 및 속도 120 km/h에서 냉각수 입구 온도차인 $5.1^{\circ}C$보다 85.3% 증가했다. 또한, 연료전지 자동차가 가혹조건인 등판 주행시 에어컨 시스템을 작동할 경우 스택의 안정적 작동을 허용하는 한계 온도인 $70^{\circ}C$를 초과할 수 있다.

• 한국안전학회지
• /
• 제37권4호
• /
• pp.129-138
• /
• 2022

A new method for injecting cooling water into the Korean research reactor (KRR) in the event of beam tube rupture is proposed in this paper. Moreover, the research evaluates the risk to the reactor core in terms of core damage frequency (CDF). The proposed method maintains the cooling water in the chimney at a certain level in the tank to prevent nuclear fuel damage solely by gravitational coolant feeding from the emergency water supply system (EWSS). This technique does not require sump recirculation operations described in the current procedure for resolving beam tube accidents. The reduction in the risk to the core in the event of beam tube rupture that can be achieved by the proposed change in the cooling water injection design is quantified as follows. 1) The total CDF of the KRR for the proposed design change is approximately 4.17E-06/yr, which is 8.4% lower than the CDF of the current design (4.55E-06/yr). 2) The CDF for beam tube rupture is 7.10E-08/yr, which represents an 84.1% decrease compared with that of the current design (4.49E-07/yr). In addition to this quantitative reduction in risk, the modified cooling water injection design maintains a supply of pure coolant to the EWSS tank. This means that the reactor does not require decontamination after an accident. Thermal hydraulic analysis proves that the water level in the reactor pool does not cause damage to the nuclear fuel cladding after beam tube rupture. This is because the amount of water in the chimney can be regulated by the EWSS function. The EWSS supplies emergency water to the reactor core to compensate for the evaporation of coolant in the core, thus allowing water to cover the fuel assemblies in the reactor core over a sufficient amount of time.

• Nuclear Engineering and Technology
• /
• 제54권12호
• /
• pp.4571-4584
• /
• 2022

The analysis of rapid flow transients in Reactor Coolant Pumps (RCP) is essential for a reactor safety study. An accurate and precise analysis of the RCP coastdown is necessary for the reactor design. The coastdown of RCP affects the coolant temperature and the colloidal crud in the primary coolant. A realistic and kinetic model has been used to investigate the behavior of activated colloidal crud in the primary coolant and steam generator that solves the pump speed analytically. The analytic solution of the non-dimensional flow rate has been determined by the energy ratio β. The kinetic energy of the coolant fluid and the kinetic energy stored in the rotating parts of a pump are two essential parameters in the form of β. Under normal operation, the pump's speed and moment of inertia are constant. However, in a coastdown situation, kinetic damping in the interval has been implemented. A dynamic model ACCP-SMART has been developed for System Integrated Modular and Advanced Reactor (SMART) to investigate the corrosion due to activated colloidal crud. The Fickian diffusion model has been implemented as the reference corrosion model for the constituent component of the primary loop of the SMART reactor. The activated colloidal crud activity in the primary coolant and steam generator of the SMART reactor has been studied for different equilibrium corrosion rates, linear increase in corrosion rate, and dynamic RCP coastdown situation energy ratio b. The coolant specific activity of SMART reactor equilibrium corrosion (4.0 mg s^-1) has been found 9.63×10^-3 µCi cm^-3, 3.53×10^-3 µC cm^-3, 2.39×10^-2 µC cm^-3, 8.10×10^-3 µC cm^-3, 6.77× 10^-3 µC cm^-3, 4.95×10^-4 µC cm^-3, 1.19×10^-3 µC cm^-3, and 7.87×10^-4 µC cm^-3 for ²⁴Na, ⁵⁴Mn, ⁵⁶Mn, ⁵⁹Fe, ⁵⁸Co, ⁶⁰Co, ⁹⁹Mo, and ⁵¹Cr which are 14.95%, 5.48%, 37.08%, 12.57%, 10.51%, 0.77%, 18.50%, and 0.12% respectively. For linear and exponential coastdown with a constant corrosion rate, the total coolant and steam generator activity approaches a higher saturation value than the normal values. The coolant and steam generator activity changes considerably with kinetic corrosion rate, equilibrium corrosion, growth of corrosion rate (ΔC/Δt), and RCP coastdown situations. The effect of the RCP coastdown on the specific activity of the steam generators is smeared by linearly rising corrosion rates, equilibrium corrosion, and rapid coasting down of the RCP. However, the time taken to reach the saturation activity is also influenced by the slope of corrosion rate, coastdown situation, equilibrium corrosion rate, and energy ratio β.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.110-114
• /
• 2001

A numerical analysis has been perfonned to estimate the effect of turbulent penetration and thermal stratified flow in the branch lines piping. This phenomenon of thermal stratification are usually observed in the piping lines of the safety related systems and may be identified as the source of fatigue in the piping system due to the thermal stress loading which are associated with plant operating modes. The turbulent penetration length reaches to $1^{st}$ valve in safety injection piping from reactor coolant system (RCS) at normal operation for nuclear power plant when a coolant does not leak out through valve. At the time, therefore, the thermal stratification does not appear in the piping between RCS piping and $1^{st}$ valve of safety injection piping. When a coolant leak out through the $1^{st}$ valve by any damage, however, the thermal stratification can occur in the safety injection piping. At that time, the maximum temperature difference of fluid between top and bottom in the piping is estimated about $50^{\circ}C$.

• 한국압력기기공학회 논문집
• /
• 제14권1호
• /
• pp.58-65
• /
• 2018

The purpose of this study is to develop a Half Nozzle Repair(HNR) process to prevent the leakage from welds on small bore piping in Reactor Coolant System. The Codes & Standards of tempered bead and design requirements of J-Groove welds are reviewed. Automatic machine GTAW welding and machining equipments are developed to perform HNR process. Single pass welding and overlay welding equipments are conducted in order to obtain the optimal temper bead welding process parameters with Alloy 52M filler wire. Coarse grain heat affected zone(CGHAZ) is formed by rapid cooling rate in heat affected zone after welding. Accordingly, a proper temper bead technique is required to reduce CGHAZ in 1-Layer of welds by 2- and 3-Layers. Mock-up tests show that the developed HNR process is possible to meet ASME Code & Standard requirements without any defect.