• Journal of Aquaculture
• /
• v.1 no.1
• /
• pp.67-73
• /
• 1988

A growth experiment of tilapia (offsprings of the hybrid between Oreochromis niloticus and O. mossambicus) under different dissolved oxygen levels in the recirculating water system was conducted at the Fish Culture Experiment Station of the National Fisheries University of Pusan from February 4 to March 5, 1986. Six tanks with a capacity of $1.8m^3$ of water each were used under the same condition of water parameters except for dissolved oxygen levels which were designated to maintain at 1.5, 2.0, 2.5, 3.0, 3.5 and 4.0 mg/$\iota$. Each tank was stocked with 90 kg of fish each averaging 64 to 69 grams. The average water temperature during the course of the experiment was $22.5^{\circ}C$. The results obtained are summarized as follows: The food conversion efficiencies were very good, being 1.05-1.11 at 3.5, 3.0, 2.5 and 2.0 mg/$\iota$ DO levels without any significant differences among them, but at 4.0 mg/$\iota$ the F. C. was 1.39 and at 1.5 mg/$\iota$ it was 1.61 being very poor compared with the others. The daily growth rate performance was best at 3.5 mg/$\iota$ dissolved oxygen level followed by 3.0 and 2.5 mg/$\iota$ with slight differences while at 4.0 and 2.0 mg/$\iota$ DO levels the growths were significantly poor, and at 1.5 mg/$\iota$ DO level it was extremely poor. In 1.5 mg/$\iota$ group, the fish did not accept feed vigorously and after feeding the fish usually concentrated around the inflow point showing oxygen deficiency response. While at 4.0 mg/$\iota$ high feeding rates tended to waste significant amounts of feed while eating and led to water deterioration, and above these levels the results is considered to lead to a waste of energy with uneconomical performance. On the other hand, at and below 2.0 mg/$\iota$ DO level the tilapia certainly showed a poor growth performance. The experiment indicates that the DO range of 2.5$\~$3.5 mg/$\iota$ is the optimum level for the good growth performance.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.1 s.55
• /
• pp.64-75
• /
• 2005

The total production of food waste was about 11,398ton/day('03) in Korea. Also, food waste was treated by landfill, incineration, reuse and anaerobic digestion. The method of food waste treatment depended primarily on landfill. However, the method of landfill causing social problems was prevented to treat food waste in the first of January 2005.12) Thus, anaerobic digestion is an important method to treat food waste because of possibility of energy recovery as methane gas. In this study, the possibility of food waste treatment containing high organic material and low pH in the one stage anaerobic reactor to save cost and time and energy recovery using $CH_{4}$ gas by the hybrid anaerobic reactor (HAR) was measured. The HAR was designed by combing the merits of the anaerobic filter (AF) to minimize the microorganism shock when food waste of very low pH was injected and up-flow anaerobic sludge blanket (UASB) to prevent from plugging and channeling phenomena by large suspended solids when semi solids were injected. Granule was packed in the section of HAR. The purpose of the BMP experiment was to measure the amount of methane generated when organic material was resolved under anaerobic conditions, to grasp bio resolution of organic material. Total accumulated methane production per VS amount was $0.471(m^{3}/\cal{kg}\;VS)$. So, the value was about $81.2\%$ of theoretical methane production which was $0.58(m^{3}/\cal{kg}\;VS)$ by elementary analysis and organic matter removal velocity (K) was $0.18(d^{-1})$. From these results, food waste was treated by anaerobic treatment. From this study, $CH_{4}$ generation from food waste (11,398 ton/day) could be estimated. By using an energy conversion factor of Braun's study, $5.97KWh/m^{3}\;CH4,\;60\%\;of\;CH_{4}$ gas generation, the amount of total energy producing food waste is to 6,727MWh/day. It could be confirmed that energy recovery using $CH_{4}$ gas was possible. Above these results, food waste containing organic matters of high concentration could be treated in HRT 30 days under an anaerobic condition, using the hybrid anaerobic reactor and reuse of $CH_{4}$ gas was possible.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.34-45
• /
• 2016

Global warming and climate change have been caused by combustion of fossil fuels. The greenhouse gases contributed to the rise of temperature between $0.6^{\circ}C$ and $0.9^{\circ}C$ over the past century. Presently, fossil fuels account for about 88% of the commercial energy sources used. In developing countries, fossil fuels are a very attractive energy source because they are available and relatively inexpensive. The environmental problems with fossil fuels have been aggravating stress from already existing factors including acid deposition, urban air pollution, and climate change. In order to control greenhouse gas emissions, particularly CO2, fossil fuels must be replaced by eco-friendly fuels such as biomass. The use of renewable energy sources is becoming increasingly necessary. The biomass resources are the most common form of renewable energy. The conversion of biomass into energy can be achieved in a number of ways. The most common form of converted biomass is pellet fuels as biofuels made from compressed organic matter or biomass. Pellets from lignocellulosic biomass has compared to conventional fuels with a relatively low bulk and energy density and a low degree of homogeneity. Thermal pretreatment technology like torrefaction is applied to improve fuel efficiency of lignocellulosic biomass, i.e., less moisture and oxygen in the product, preferrable grinding properties, storage properties, etc.. During torrefacton, lignocelluosic biomass such as palm kernell shell (PKS) and empty fruit bunch (EFB) was roasted under an oxygen-depleted enviroment at temperature between 200 and $300^{\circ}C$. Low degree of thermal treatment led to the removal of moisture and low molecular volatile matters with low O/C and H/C elemental ratios. The mechanical characteristics of torrefied biomass have also been altered to a brittle and partly hydrophobic materials. Unfortunately, it was much harder to form pellets from torrefied PKS and EFB due to thermal degradation of lignin as a natural binder during torrefaction compared to non-torrefied ones. For easy pelletization of biomass with torrefaction, pellets from PKS and EFB were manufactured before torrefaction, and thereafter they were torrefied at different temperature. Even after torrefaction of pellets from PKS and EFB, their appearance was well preserved with better fuel efficiency than non-torrefied ones. The physical properties of the torrefied pellets largely depended on the torrefaction condition such as reaction time and reaction temperature. Temperature over $250^{\circ}C$ during torrefaction gave a significant impact on the fuel properties of the pellets. In particular, torrefied EFB pellets displayed much faster development of the fuel properties than did torrefied PKS pellets. During torrefaction, extensive carbonization with the increase of fixed carbons, the behavior of thermal degradation of torrefied biomass became significantly different according to the increase of torrefaction temperature. In conclusion, pelletization of PKS and EFB before torrefaction made it much easier to proceed with torrefaction of pellets from PKS and EFB, leading to excellent eco-friendly fuels.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.3
• /
• pp.171-177
• /
• 2007

This study suggested a new method to stabilize molten salt wastes generated from the pyre-process for the spent fuel treatment. Using conventional sol-gel process, $SiO_2-Al_2O_3-P_2O_5$ (SAP) inorganic material that is reactive to metal chlorides were prepared. In this paper, the reactivity of SAP with the metal chlorides at $650{\sim}850$, the thermal stability of reaction products and their leach-resistance under the PCT-A test method were investigated. Alkali metal chlorides were converted into metal aluminosilicate($LixAlxSi1-_xO_{2-x}$) and metal phosphate($Li_3PO_4\;and\;Cs_2AlP_3O_{10}$) While alkali earth and rare earth chlorides were changed into only metal phosphates ($Sr_5(PO_4)_3Cl\;and\;CePO_4$). The conversion rate was about $96{\sim}99%$ at a salt waste/SAP weight ratio of 0.5 and a weight loss up to $1100^{\circ}C$ measured by thermogravimetric analysis were below 1wt%. The leach rates of Cs and Sr under the PCT-A test condition were about $10^{-2}g/m^2\;day\;and\;10^{-4}g/m^2\;day$. From these results, it could be concluded that SAP can be considered as an effective stabilizer for metal chlorides and the method using SAP will give a chance to reduce the volume of salt wasteform for the final disposal through further researches.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2197-2204
• /
• 2000

Lignin is a major component of wastewater generated in the chemical processing of wood. Because it is recalcitrant, it inhibits biological treatment of wastewater of pulp manufacturing, especially high concentration of lignin may inhibit the anaerobic digestion. The objective of this study was to evaluate the toxicity of high molecular hardwood lignin (lignosulfonate, MW $\geq$ 20,000) on aceticlastic methanogens in the batch reactors at different temperatures with different sludge concentrations, using anaerobic serum bottles. The hardwood lignin was found to inhibit anaerobic conversion of acetate to methane and carbon dioxide, shown with a long lag-phase before methanogenesis started. The methanogens assumed not to be able to acclimate to the lignin were found to be acclimated slowly in the batch experiments, finally reaching non-toxic levels in which methane production could start. The hardwood lignin was found not to be bacteriocidal but bacteriostatic to aceticlastic methanogens. Hardwood lignin(lignosulfonate) at 1.3, 2.6, and 3.9%(w/w) inhibited the acetateutilizing methanogens of anaerobic digester sludge by 14.5, 17.8, 21.1 days(in noninhibitory condition it took 10 days) to produce the same amount of methane. The inhibitory effect of lignin was examined at temperature ranges of $30^{\circ}C$ to $50^{\circ}C$. When 2.6% of lignin was contained in wastewater, methane production was highest at $30^{\circ}C$ during initial 8 days. At $4^{\circ}C$, methane production rapidly increased after 12 days of digestion, the value became higher than that at $30^{\circ}C$ after 14 days. However, the methane production was completely inhibited during whole digestion period at $50^{\circ}C$. High ratio of lignin concentration to initial anaerobic sludge concentration gave tolerance to the inhibition. In this experiment, high molecular hardwood lignin was not degraded and decolorized.

• Progress in Medical Physics
• /
• v.20 no.1
• /
• pp.21-29
• /
• 2009

Breast cancer is the most common form of cancer among korean woman. Therefore, the early detection activities of breast cancer such as breast self-examinations, clinical breast examinations, mammography are important. A yearly mammography examination has been recommended for women aged 40 and older for the early detection of breast cancer in asymptomatic periods. However, the glandular tissue of breast is the most radiation-sensitive tissue, and the determination of average glandular dose (AGD) forms an important part of the quality control of the mammographic systems. Because of the difficulty of estimating AGD directly, it is often estimated from the measurements of the incident air kerma and by applying the appropriate conversion factors. The primary objective of this study was to standardize the method of measuring AGD. The secondary objective was to evaluate the relationships between AGD per various composition and thickness of the breast using Monte Carlo simulations. As a result, we standardized the method of measuring AGD according to International Atomic Energy Agency (IAEA) guidelines (CoP: an international code of practice). Overall, AGD for mammographic practice in Korea was less than 3.0 mGy recommended by the Korea Food and Drug Adminstration (KFDA) protocol, and Korean Institute for Accreditation of Medical Image (KIAMI). The measured and simulated AGD for a given condition were calculated as 1.7 and 1.6 mGy, respectively. For the AGDs obtained, there was no significant difference between them. The simulated AGD was dependent on the fraction of glandular tissue of the breast. The AGD increases with increasing of the breast glandularity due to increasing absorption of low energy photons. The AGD also increases as a function of breast thickness. In conclusion, the results of this study could be used as a baseline to establish a reference level of radiation dose in mammography.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.4
• /
• pp.228-234
• /
• 2004

In organic farming, nutrients for the crop production are mostly supplied by compost containing various organic materials. The long-term organic cultivation would result in continuous changes of soil chemical properties and fertility. The aim of this study was to investigate the contribution of long-term organic cultivation to the soil fertility in Korea focusing on the chemical properties of soil. Soil samples were collected from organic farms that had been cultivated for 8-10 years after certification of organic product through the conversion periods of 2-3 years. Thereby each organic farm had acquired optimal cultivating techniques and soil condition. We separated organic farms into three groups by cultivating crops, i.e. leaf vegetables, fruit vegetables and fruit trees. In each group, five representative farms were chosen in order to investigate the relationships between application rate of compost and nutrient contents in soil. The application rate of compost was approximately $10-15Mg\;10a^{-1}$ for the first 2-3 years at the beginning of organic farming and then reduced to a rate of $3-4Mg\;10a^{-1}$ after stabilization of organic matter content in soil with $30-50g\;10a^{-1}$. However, the continuous organic farming for 8-10 years resulted in accumulation of nutrients, especially of P, in soil probably due to the excessive amounts of compost applied. In conclusion, we suggest that the application rate and organic sources of compost should be decided on the basis of P content in soil by soil testing and thereafter the lack of soil N content for crop cultivation should be compensated by crop rotation with such as legumes. This might be an approach to the original meaning of organic farming as an environmental friendly agriculture.

• Journal of Animal Science and Technology
• /
• v.48 no.2
• /
• pp.219-226
• /
• 2006

The wastes (the needle leaves and branches) produced from thinning the forest were fermented under an anaerobic condition (pine silage) to utilize as a forage source of ruminants. An in situ trial was conducted with two ruminally fistulated Korean native cows by 4 replicates (2 bags per cow), and in vivo digestibility of pine silage was estimated with five Korean native steers by 5 replicates in incomplete double turn-over design. In order to investigate feed efficiency and carcass traits, forty eight Korean native bulls were assigned to four treatments (0%, 25%, 50%, 75% of pine silage) with a completely randomized design in 12 pens accommodating 4 animals per pen. The amounts of concentrate and roughage allowed to experimental animals were in the range of 2.5% and 0.6% of body weight, respectively. Animals had freely accessed to mineral block and water in stanchion barn.An in situ crude protein digestibility of the roughage sources when suspended for 48 hrs in the rumen was higher for feeding the pine silage than the rice straw, whereas NDF digestibility was vice versa. No differences between the treatments were observed in in vivo digestibilities of dry matter, crude protein and NDF. Daily body weight gain was significantly (P<0.01) higher for the pine silage substitutions compared with the rice straw feeding except for the 25% silage feeding. The pine silage feeding did not affect feed efficiency.In carcass traits, marbling score tended to be higher for the 50% pine silage treatment than the other treatments while back fat thickness tended to be the thinnest for the rice straw feeding. From these results, it may be recommended to substitute pine silage, as a forage source, for rice straw by 50 percent.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.18-24
• /
• 2012

Lignocellulose is difficult to hydrolyze due to the presence of lignin and the technology developed for cellulose fermentation to ethanol is not yet economically viable. However, recent advances in the extremely new field of biotechnology for the ethanol production are making it possible to use of Agriculture residual biomass, e.q., Barley straw, because of their several superior aspects as Agriculture residual biomass; low lignin, high contents of carbohydrates. Barley straw consists of 39.78% cellulose (glucose), 22.56% hemicelluloses and 19.27% lignin. Pretreatment of barley straw using NaOH pretreatment solutions concentration with 2%, temperature $85^{\circ}C$ and reaction times 1 hr were investigates. $NH_4OH$ pretreatment condition was solutions concentration with 15%, temperature $60^{\circ}C$, and reaction times 24hr were investigates. Furthermore, enzymatic saccharification using cellulose at $50^{\circ}C$, pH 4.8, 180 rpm for conversion of cellulose contained in barley straw to monomeric sugar. The pretreatment of barley straw using NaOH and $NH_4OH$ can significantly improve enzymatic saccharification of barley straw by extract more lignin and increasing its accessibility to hydrolytic enzymes. The result showed NaOH pretreatment extracted yield of lignin was 24.15%. $NH_4OH$ pretreatment extracted yield of lignin was 29.09%. Shaccharification of barley straw pretreatment by NaOH for 72hr and pH 4.8 result in maximum glucose concentration 15.39g/L (58.40%) and by $NH_4OH$ for 72hr and pH 4.8 result in maximum glucose concentration 16.01g/L (64.78%).

• Korean Journal of Poultry Science
• /
• v.40 no.3
• /
• pp.253-262
• /
• 2013

This experiment was conducted to investigate the effects of floor type and heating system on performance, housing environment and health status of ducks reared in three types of duck house (OD : Open floor house-Direct heating system, OF : Open floor house-Floor heating system and LD : Loft type house-Direct heating system). In OF treatment, PVC pipes were installed for heating under concrete floor and covered with litter. In LD treatment, plastic mesh was installed 50 cm above the floor so that duck's droppings can pass through it. Each treatment had four replicates of 25 birds (Cherry Valley duck breed) per pen. There were no significant differences in weight gain and feed intake of ducks for 6 weeks among all treatments. However, feed conversion ratio in LD was significantly higher (p<0.05) than that in OF. No differences were found in carcass charac- teristics, with the exception of abdominal fat weight where OF were higher than the others. Concentrations of $CO_2$ and $NH_3$ gas in OD were higher than those of OF and LD at 3, 4 and 5 weeks. Moisture content in litter of OF was lower than that of OD. In contrast, the amount of dust in the air was higher in OF than in OD. The amount of fuel used for 6 weeks in LD was lower about 21% than that in OD. Some of unusual symptoms were observed in open floor house and loft type house, such as lying, spraddle legged, twisted ankle and legs, wounded sole, or etc. No components of leukocyte and erythrocyte of blood were significantly different among all treatments. The results of this experiment showed that OF and LD systems had no positive effects on performance of meat type commercial duck. However, there were some positive effects of certain house type for the improvement of environmental condition in duck house for hygienic production. In the future, more research on the effect of various facilities and systems for duck house is needed.