• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.596-601
• /
• 2020

Silicon carbide is considered a potentially useful material for high-temperature electronic devices because of its large band gap energy and p-type or n-type conduction that can be controlled by impurity doping. Accordingly, the thermoelectric properties of -SiC powder prepared by refined diatomite were investigated for high value-added applications of natural diatomite. -SiC powder was synthesized by a carbothermal reduction of the SiO₂ in refined diatomite using carbon black. An acid-treatment process was then performed to eliminate the remaining impurities (Fe, Ca, etc.). n-Type semiconductors were fabricated by sintering the pressed powder at 2000℃ for 1~5h in an N2 atmosphere. The electrical conductivity increased with increasing sintering time, which might be due to an increase in carrier concentration and improvement in grain-to-grain connectivity. The carrier compensation effect caused by the remaining acceptor impurities (Al, etc.) in the obtained -SiC had a deleterious influence on the electrical conductivity. The absolute value of the Seebeck coefficient increased with increasing sintering time, which might be due to a decrease in the stacking fault density accompanied by grain or crystallite growth. On the other hand, the power factor, which reflects the thermoelectric conversion efficiency of the present work, was slightly lower than that of the porous SiC semiconductors fabricated by conventional high-purity -SiC powder, it can be stated that the thermoelectric properties could be improved further by precise control of an acid-treatment process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.246-252
• /
• 2020

Safety accidents have been reported due to falling accumulated snow from cables of cable-supported bridges. In addition to the direct damage caused by falling snow, secondary damage, such as traffic accidents, can occur. Various methods have been proposed to prevent these accidents, but there are still problems in safety and practicality. In this study, a cable robot type was selected as one of the active methods for removing accumulated snow on cables. An attempt was made to increase the climbing ability of the robot to improve the efficiency of snow removal. In addition, the available range of cable diameter for the robot can be adjusted flexibly to be applied to cables used in the field. A high-resolution camera was also installed to check the surface condition of the cable in real time to increase the utility, and be used as a cable inspection robot. A three-axis accelerometer and a tension conversion algorithm were added to measure the tension force of cables. To verify the performance, indoor and field experiments were conducted, and future improvements for the inspection robot were proposed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.3
• /
• pp.237-244
• /
• 1994

To elucidate the physiological characteristics of 2 japonica type and 2 tongil type of rice cultivars, photosynthesis, respiration and diurnal changes of photosynthesis rate had been investigated 6 times at each growing stage. The ratios of photosynthetic part of tongil types were higher than those of japonica types at tillering stage. The highest photosynthetic activity was measured on August 1, before heading in each growing stage, and efficiency of photosynthesis showed its the highest on July 25. Diurnal photosynthetic curve at heading stage reached the peak at 11-12 AM, but after 2 weeks from heading stage, the peak apperred at 1-2 PM. Conversion of respiration into photosynthesis for $CO_2$ fixation started 30~60 minutes later than the standard sunrise time and reconversion for carborhdrate accmulation began 50~60 minutes earlier than the standard sunset time. Photosynthesis showed positive correlation with chlorophyll content and root activity. Harvest index of tongil type cultivars were significantly higher than those of japonica type cultivars.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.8
• /
• pp.1199-1208
• /
• 2005

Abatement of greenhouse gas emitted from ruminants and promotion of biogas energy from animal effluent were comprehensively examined in each anaerobic fermentation reactor and animal experiments. Moreover, the energy conversion efficiency of biomass energy to power generation were evaluated with a gas engine generator or proton exchange membrane fuel cell (PEMFC). To mitigate safely rumen methanogenesis with nutritional manipulation the suppressing effects of some strains of lactic acid bacteria and yeast, bacteriocin, $\beta$1-4 galactooligosaccharide, plant extracts (Yucca schidigera and Quillaja saponarea), L-cysteine and/or nitrate on rumen methane emission were compared with antibiotics. For in vitro trials, cumulative methane production was evaluated using the continuous fermented gas qualification system inoculated with the strained rumen fluid from rumen fistulated Holstein cows. For in vivo, four sequential ventilated head cages equipped with a fully automated gas analyzing system were used to examine the manipulating effects of $\beta$1-4 galactooligosaccharide, lactic acid bacteria (Leuconostoc mesenteroides subsp. mesenteroides), yeast (Trichosporon serticeum), nisin and Yucca schidigera and/or nitrate on rumen methanogenesis. Furthermore, biogas energy recycled from animal effluent was evaluated with anaerobic bioreactors. Utilization of recycled energy as fuel for a co-generator and fuel cell was tested in the thermophilic biogas plant system. From the results of in vitro and in vivo trials, nitrate was shown to be a strong methane suppressor, although nitrate per se is hazardous. L-cysteine could remove this risk. $\beta$1-4 galactooligosaccharide, Candida kefyr, nisin, Yucca schidigera and Quillaja saponarea are thought to possibly control methanogenesis in the rumen. It is possible to simulate the available energy recycled through animal effluent from feed energy resources by making total energy balance sheets of the process from feed energy to recycled energy.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.12
• /
• pp.1268-1272
• /
• 2008

Low temperature plasma applied with partial oxidation is a technique to produce synthesis gas from methane. Low temperature plasma reformer has superior miniaturization and start-up characteristics to reformers using steam reforming or CO$_2$ reforming. In this research, a low temperature plasma reformer using GlidArc discharge was proposed. Reforming characteristics for each of the following variables were studied: gas components ratio (O$_2$/CH$_4$), the amount of steam, comparison of reaction on nickle and iron catalysts and the amount of CO$_2$. The optimum conditions for hydrogen production from methane was found. The maximum Hydrogen concentration of 41.1% was obtained under the following in this condition: O$_2$/C ratio of 0.64, total gas flow of 14.2 L/min, catalyst reactor temperature of 672$^{\circ}C$, the amount of steam was 0.8, reformer energy density of 1.1 kJ/L with Ni catalyst in the catalyst reactor. At this point, the methane conversion rate, hydrogen selectivity and reformer thermal efficiency were 66%, 93% and 35.2%, respectively.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.2
• /
• pp.151-158
• /
• 2016

Tidal farm is a multi-arrayed turbine system for utilizing tidal stream energy. For horizontal-axis turbine(HAT) system, it is recommended that each unit has to be deployed far apart in order to avoid hydrodynamic interference among turbines, as proposed by the European Marine Energy Centre(EMEC). But there is no rule for the arrangement of vertical-axis turbine(VAT) yet. Moreover it has been reported that a proper arrangement of adjacent turbines can enhance the overall efficiency even greater than an arrangement without mutual interference effect. This paper suggests the layout of VATs showing the better performances, which turned out to be quite different from HATs' arrangement. Numerical calculations were performed to investigate the performance variation in terms of the rotational direction as well as the distance between turbines. It has been shown that the best combination of rotational direction and distance between turbines can increase its performance higher about 9.2% than that of two independently operated turbines. It is likely that such improvement is due to the increased velocity between adjacent turbines. For diagonally arranged turbines, the maximum normalized mean power coefficient was obtained to be higher about 5.6% than that of two independent turbines. It is expected that the present results can be utilized for conceptual design of tidal farm to harness the tidal stream energy.

• Journal of radiological science and technology
• /
• v.35 no.4
• /
• pp.309-314
• /
• 2012

Nowadays, digital Radiography (DR) systems are widely used in clinical sites and substitute the analog-film x-ray imaging systems. The resolution of DR images depends on several factors such as characteristic contrast and motion of the object, the focal spot size and the quality of x-ray beam, x-ray scattering, the performance of the DR detector (x-ray conversion efficiency, the intrinsic resolution). The DR detector is composed of an x-ray capturing element, a coupling element and a collecting element, which systematically affect the system resolution. Generally speaking, the resolution of a medical imaging system is the discrimination ability of anatomical structures. Modulation transfer function (MTF) is widely used for the quantification of the resolution performance for an imaging system. MTF is defined as the frequency response of the imaging system to the input of a point spread function and can be obtained by doing Fourier transform of a line spread function, which is extracted from a test image. In clinic, radiologic technologists, who are in charge of system maintenance and quality control, have to evaluate or make routine check on their imaging system. However, it is not an easy task for the radiologic technologists to measure MTF accurately due to lack of their engineering and mathematical backgrounds. The objective of this study is to develop and provide for radiologic technologists a medical system imaging evaluation tool, so that they can measure and quantify system performance easily.

• Journal of Korea Spatial Information System Society
• /
• v.7 no.3 s.15
• /
• pp.107-118
• /
• 2005

Various spatial data are utilized, through geographic information system, for the process to make a decision related to space. Generally, spatial data is large in quantity and it costs high and takes quite a long time for producing and maintaining it. An existing spatial data management system, tile-based one, for digital map manages spatial data being separated by a uniform data unit called tile. These systems can be implemented easily but have many problems such as they can directly store and manage feature included in tile. Therefore, in this paper, we suggest a feature-based spatial data management system for digital map. The proposed system is able to store and manage spatial data in the unit of feature directly. Hence this system is able to immediately update any change in the data and to supply users with the updated data without any delay. The proposed system can not only support a function of data input, management, supplying and update but also support unity origin coordinate conversion, UFID creation, feature unifying, feature dividing and metadata input which is not supported by the existing tile-based system. The proposed system can easily manage spatial data and can increase efficiency in processing and application.

• Journal of the Korean Vacuum Society
• /
• v.22 no.1
• /
• pp.37-44
• /
• 2013

In order to investigate an influence of carrier trap by quantum dots (QDs) on the solar parameters, in this study, the $p^+-QD-n/n^+$ solar cells with InAs/GaAs QD active layers are fabricated, and their characteristics are investigated and compared with those of a GaAs matrix solar cell (MSC). Two different types of QD structures, the Stranski-Krastanow (SK) QD and the quasi-monolayer (QML) QD, have been introduced for the QD solar cells, and the parameters (open-circuit voltage ($V_{OC}$), short-cirucuit current ($I_{SC}$), fill factor (FF), conversion efficiency (CE)) are determined from the current-voltage characteristic curves under a standard solar illumination (AM1.5). In SK-QSC, while FF of 80.0% is similar to that of MSC (80.3%), $V_{OC}$ and $J_{SC}$ are reduced by 0.03 V and $2.6mA/cm^2$, respectively. CE is lowered by 2.6% as results of reduced $V_{OC}$ and $J_{SC}$, which is due to a carrier trap into QDs. Though another alternative structure of QML-QD to be expected to relieve the carrier trap have been firstly tried for QSC in this study, it shows negative results contrary to our expectations.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.800-804
• /
• 2007

전 세계에서 홍수로 인한 인명손실과 재산적 피해의 기록을 살펴보면 최근 몇 년 동안 꾸준히 증가하고 있다. 이로 인해서 홍수를 방어하기 위한 노력은 증가하게 되었다. 이로 인해 홍수터에서 인구집중과 개발로 인해 홍수방어를 위해서 막대한 투자가 필요하다. 이와 동시에 지속가능하고 효과적인 수자원 관리는 전체적인 접근방법이 요구되며, 사회와 경제발전과 생태계 보호 및 토지이용과 수자원 이용의 적절한 관리와 연결된 개념이 필요하다. 유역은 육지와 수계 사이의 많은 상호작용이 있는 동적인 시스템이다. 이러한 관점에서 유역을 간단한 고정된 지역적인 문제라고 생각하는 것보다 전체로서의 유역 기능을 개선하는데 노력이 필요하고 시도되어야 할 것이다. 통합홍수관리(IFM : Integrated Flood Management)는 홍수의 긍정적인 측면과 부정적인 측면을 고려한 새로운 접근방법이며, 홍수가 자원적 가치를 지닌 것이라고 생각하는 개념이다. 통합홍수관리의 특징은 홍수조절 대책의 적절한 혼합, 대책의 목적 및 형태(구조적 및 비구조적 대책), 단기간 및 장기간 대책 등의 대책들을 통합하는 것이다. 여기에는 전유역의 수문순환 관리, 통합 토지이용 및 수자원 관리, 최적 혼합대책의 적용 및 통합재해관리 적용 등이 있다. 홍수는 자연적인 수문학적 체계의 중요한 요소이며, 주요 수자원이기도 하다. 그리고 빈번한 홍수로 인해 제방을 넘어 홍수터를 점령한다. 이 결과로 상습 홍수범람지역은 점점 더 인구가 밀집되고 있고 홍수에 더 취약하게 된다. 그러므로 금호강유역에 발생한 홍수의 개요, 원인 및 결과에 대해서 살펴보고, 홍수관리대책과 실효성에 대해서 조사 분석하였다. 그리고 홍수가 발생한 후 홍수관리대책과 관리기술의 변화를 통합홍수관리의 개념에서 분석하였다.Jones matrix, which allows a new interpretation in the conversion efficiency of the thin-film optical waveguides.있다는 장점이 있었다. 따라서 소아에서 복막투석도관 수술 시 복강경적 방법을 이용하는 것이 효율적인 복막 투석을 위해 유용하다고 생각된다.상부 방광천자에 비해 민감도 59.5%(25/42), 특이도 86.6%(13/15)였고 위양성률 13.3%(2/15), 위음성률 40.5%(17/42) 로 정확도가 낮았다. 결론 : 소변을 가리지 못하는 영유아에서 요로 감염을 진단하기 위해서는 도뇨관 채뇨에 비해 초음파 감시하 치골상부 방광천자가 정확하고 안전한 채뇨법으로 권장되어야 한다고 생각한다.應裝置) 및 운용(運用)에 별다른 어려움이 없고, 내열성(耐熱性)이 강(强)하므로 쉬운 조건하(條件下)에서 경제적(經濟的)으로 공업적(工業的) 이용(利用)에 유리(有利)하다고 판단(判斷)되어진다.reatinine은 함량이 적었다. 관능검사결과(官能檢査結果) 자가소화(自家消化)시킨 크릴간장은 효소(酵素)처리한 것이나 재래식 콩간장에 비하여 품질 면에서 손색이 없고 저장성(貯藏性)이 좋은 크릴간장을 제조(製造)할 수 있다는 결론을 얻었다.이 있음을 확인할 수 있었다.에 착안하여 침전시 슬러지층과 상등액의 온도차를 측정하여 대사열량의 발생량을 측정하고 슬러지의 활성을 측정할 수 있는 방법을 개발하였다.enin과 Rhaponticin의 작용(作用)에 의(依)한 것이며, 이는 한의학(韓醫學) 방제(方劑) 원리(原理)인 군신좌사(君臣佐使) 이론(理論)에서 군약(君藥)이 주증(主症)에 주(主)로 작용(作用)하는 약물(藥物)이라는 것을 밝혀주는 것이라고 사료(思料)된다.일전 $