• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.5
• /
• pp.325-335
• /
• 2018

We herein present a study on the active phased array antenna for receiving satellite broadcasting that can electrically align its polarization to that of target transmitters in its moving condition or in the Skew angle arrangement of the broadcasting satellite receiver. Hence, we have developed an active phased array structure composed of the self-developed Vivaldi antenna and multifunction core (MFC) chip, receiving RF front end module, and control units. In particular, the new Vivaldi antenna designed in the Ku-band of 10.7 - 14.5 GHz to receive one desired polarization mode such as the horizontal or vertical by means of an MFC chip and other control units that can control the amplitude and phase of each antenna element. The test results verified that cross-polarization property is 20 dB or higher and the primary beam can be scanned clearly at approximately ${\pm}60^{\circ}$.

• Korean Journal of Optics and Photonics
• /
• v.20 no.1
• /
• pp.48-52
• /
• 2009

We make a simple electrically controllable linear polarization rotator over $360^{\circ}$ without loss by using a thick ECB(electrically controlled birefringence) liquid crystal cell and a quarter wave plate at 514.5 nm wavelength. Its operating principle can be analyzed and explained by using simple polarization analysis and experimental data. We demonstrate that the degree of polarization of the rotator is 0.964 and the temporal variation for 1 week lies within ${\pm}1$ degree. We can easily solve the problem of nonlinearity of the dependence of the rotational angle of linear polarization on the applied voltage by changing the utilized voltage range or its fitting curve.

• Current Optics and Photonics
• /
• v.7 no.5
• /
• pp.574-581
• /
• 2023

A scheme is proposed to generate triangular waveforms with alterable symmetry. The key component is a cascaded single-drive Mach-Zehnder modulator (SD-MZM) and optical polarization beam splitter-combiner architecture. In this triangular waveform generator, the bias-induced phase shift, modulation index and controllable delay difference are changeable. To generate triangular waveform signals with different symmetry indexes, different combinations of these variables are selected. Compared with the previous schemes, this generator just contains one SD-MZM and the balanced photodetector (BPD) is not needed, which means the costs and energy consumption are significantly reduced. The operation principle of this triangular waveform generator has been theoretically analyzed, and the corresponding simulation is conducted. Based on the theoretical and simulated results, some experiments are demonstrated to prove the validity of the scheme. The triangular waveform signals with a symmetry factor range of 20-80% are generated. Both experiment and theory prove the feasibility of this method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.752-757
• /
• 2011

This paper presents vibration characteristics of magnetorheological (MR) elastomer, whose elastic modulus are controllable by an applied magnetic field. By using this property, the material can be applied to vibration absorber, so that the stiffness of the absorber can be changed and actively controlled according to the magnetic flux density. However, the various performances of MR elastomer depends on different magnetically polarization direction and dimension during the manufacturing process. In this paper, in order to obtain the optimal characteristics of MR elastomer, MR elastomers with different types and dimensions are prepared for a series tests. Using this test setup, extent of natural frequency shifted against magnetic field at various excitation frequencies can be measured. Specimens prepared with 3 types which are exposed to magnetic field vertically, horizontally and unexposed during cure. Also, a set of design variables are considered to produce MR elastomers. Through the modal tests of mass structure with MR elastomer, the optimal design as well as the polarization direction of MR elastomer is obtained among the various dimensions and 3 directional types of MR elastomers.

• Journal of the Optical Society of Korea
• /
• v.19 no.1
• /
• pp.88-94
• /
• 2015

This paper reports the fabrication of a lenticular liquid crystal (LC) lens array with thermally tunable focus and with the function of a convertible lens type, using the surface structure of a UV-curable polymer and a twisted-nematic (TN) LC cell. The TN LC cell makes the LC lenticular lens function as a converging or diverging lens by controlling electrically the polarization of input light. Therefore, the focal lengths for both the converging and diverging lenses, which can be switched from the TN cell, can be tuned by changing the effective refractive index of the LC by Joule heating of the transparent electrode. As a result, the focal length of the lens with the E7 LC was changed continuously from 8.7 to 31.2 mm for the converging lens type and from -9.8 to -14.2 mm for the diverging lens when the temperature was increased from 25 to $56^{\circ}C$.

• Current Optics and Photonics
• /
• v.6 no.2
• /
• pp.183-190
• /
• 2022

Based on the linear electro-optic (EO) effect of lithium niobite (LiNbO₃, LN) crystal, an intense two-dimensional (2D) electric field sensor was analyzed, fabricated and experimentally demonstrated. The linear polarized light beam transmits along the optical axis (z-axis) of the LN crystal, and the polarization direction of the polarized light is 45° to the y-axis. The sensor can detect the intensity of a 2D electric field that is perpendicular to the z-axis. Experimental results demonstrated that the minimum detectable electric field of the sensor is 10.5 kV/m. The maximum detected electric field of the sensor is larger than 178.9 kV/m. The sensitivity of the sensor is 0.444 mV/(kV·m^-1). The variation of the sensitivity is within ±0.16 dB when the sensor is rotated around a z-axis from 0° to 360°. The variation of the sensor output optical power is within ±1.4 dB during temperature change from 19 ℃ to 26 ℃ in a day (from 7:00 AM to 23:00 PM) and temperature change from 0 ℃ to 40 ℃ in a controllable temperature chamber. All theoretical and experimental results revealed that the fabricated sensor provides technology for the direct detection of intense 2D electric fields.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.8
• /
• pp.714-719
• /
• 2011

This paper presents vibration characteristics of magnetorheological(MR) elastomer, whose elastic modulus are controllable by applied magnetic field. By using this property, the material can be applied to vibration absorber, so that the stiffness of the absorber can be changed and actively controlled according to the magnetic flux density. However, the various performances of MR elastomer depends on different polarized direction of particles by applied magnetic field and dimension during the manufacturing process. In this paper, in order to obtain the optimal characteristics of MR elastomer, MR elastomers with different types and dimensions are prepared for a series tests. Using this test setup, extent of natural frequency shifted against magnetic field at various excitation frequencies can be measured. Specimens are prepared with 3 types, as cylinder samples exposed to magnetic field vertically, horizontally and unexposed during cure, respectively. Also, a set of design variables are considered to produce MR elastomers. Through the modal tests of mass structure with MR elastomer, the optimal design as well as the polarization direction of MR elastomer is obtained among the various dimensions and 3 directional types of MR elastomers.

• Composites Research
• /
• v.25 no.6
• /
• pp.211-216
• /
• 2012

FBG sensor peaks could be split due to polarization by shear strain, when the fiber optic sensors embedded or attached to the structure. For the fiber optic sensor packages, sensor grating has to be protected from shear strains. Also, pretension has to be applied to the sensor because compressive strain must be measured. Without pretension of sensor, the sensor does not show any change of signal until it is stretched. In order to mesure compressive and tensile strains, two fixing point and prestressed sensor need. In the fixing point, just holding the optical fiber cause slip between core and cladding in the fiber. A Fixation method of prestressed FBG sensors fixed with partially stripped fibers was developed. The sensor package has the prestress controllable fixtures at the fixing points. Prestress to the sensor imposed by controlling the two fixed points with bolts and nuts make it easy to measure compressive strain as well as tensile strain. The fiber optic sensor packages applied to the actual structure and the structural monitoring system using the package can be applied to safety through surveillance.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.29-34
• /
• 2022

A fabrication process of smart windows with controllable visible light transmittance by using retardation films is proposed. The 𝛌/4-phase retardation films that can convert a linearly polarized light into circularly polarized light are achieved through photo-alignment layers and reactive mesogen (RM) coating process. Two sheets of the fabricated retardation films with different orientation angles induced to light transmission mode (45°/-45°) and light blocking mode (45°/45°) for visible wavelength. We evaluated retardation characteristics according to the thickness of the birefringent RM material and found out the optimal condition for the film with 𝚫n·d of 𝛌/4-phase. The proposed structure of the smart window exhibited the light blocking ratio improved by more than 20% in the visible wavelength (380 nm to 780 nm). Finally, it was confirmed that the feasibility of the window structure by applying to a prototype for a smart window with a size of 150 × 150 mm².