• Nuclear Engineering and Technology
• /
• 제50권1호
• /
• pp.35-42
• /
• 2018

This article presents clean core criticality calculations and control rod worth calculations for TRIGA (Training, Research, Isotope production-General Atomics) Mark II research reactor benchmark cores using Winfrith Improved Multi-group Scheme-D/4 (WIMS-D/4) and Program for Reactor In-core Analysis using Diffusion Equation (PRIDE) codes. Cores 133 and 134 were analyzed in 2-D (r, ${\theta}$) and 3-D (r, ${\theta}$, z), using WIMS-D/4 and PRIDE codes. Moreover, the influence of cross-section data was also studied using various libraries based on Evaluated Nuclear Data File (ENDF/B-VI.8 and VII.0), Joint Evaluated Fission and Fusion File (JEFF-3.1), Japanese Evaluated Nuclear Data Library (JENDL-3.2), and Joint Evaluated File (JEF-2.2) nuclear data. The simulation results showed that the multiplication factor calculated for all these data libraries is within 1% of the experimental results. The reactivity worth of the control rods of core 134 was also calculated with different homogenization approaches. A comparison was made with experimental and reported Monte Carlo results, and it was found that, using proper homogenization of absorber regions and surrounding fuel regions, the results obtained with PRIDE code are significantly improved.

• Nuclear Engineering and Technology
• /
• 제56권9호
• /
• pp.3812-3825
• /
• 2024

The axial-flow-induced vibration of fuel rods in the nuclear power plant is closely related to nuclear safety. In this article, a numerical study is performed on vibration of two elastic cylinders arranged side-by-side in axial flow. Large eddy simulation is employed to predict the turbulent flow. The numerical method has been verified using the experimental root-mean-square vibration amplitude of a single cylinder. A wide range of inflow velocities u^*, incident turbulence intensity T_u and space ratio P/D have been examined, where D and P are the diameter and centre-to-centre distance of the cylinders, respectively. The results show that the vibration amplitudes increase with an increasing u^*, comparable to the case of a single cylinder in axial flow. However, the two cylinders could bend outwards during a relatively high u^* and low T_u. Although T_u significantly affects the amplitudes of the cylinders, it does not change the vibration frequency and the critical velocity at which buckling instability occurs. As the gap between the two cylinders is sufficiently small, the vibration amplitude enhances significantly due to the pronounced hydrodynamic interaction between the two elastic cylinders and surrounding fluid. The direction of buckling is no longer random but fixed.

• Nuclear Engineering and Technology
• /
• 제55권2호
• /
• pp.452-459
• /
• 2023

The core power control is an important issue for the study of dynamic characteristics in China initiative accelerator driven subcritical system (CiADS), which has direct impact on the control strategy and safety analysis process. The CiADS is an experimental facility that is only controlled by the proton beam intensity without considering the control rods in the current engineering design stage. In order to get the optimized operation scheme with the stable and reliable features, the variation of beam intensity using the continuous and periodic control approaches has been adopted, and the change of collimator and the adjusting of duty ratio have been proposed in the power control process. Considering the neutronics and the thermal-hydraulics characteristics in CiADS, the physical model for the core power control has been established by means of the point reactor kinetics method and the lumped parameter method. Moreover, the multi-inputs single-output (MISO) logical structure for the power control process has been constructed using proportional integral derivative (PID) controller, and the meta-heuristic algorithm has been employed to obtain the global optimized parameters for the stable running mode without producing large perturbations. Finally, the verification and validation of the control method have been tested based on the reference scenarios in considering the disturbances of spallation neutron source and inlet temperature respectively, where all the numerical results reveal that the optimization method has satisfactory performance in the CiADS core power control scenarios.

• Journal of Periodontal and Implant Science
• /
• 제29권2호
• /
• pp.371-387
• /
• 1999

The present study was performed to assess and compare the clinical and microbiological effects following local application of 2% minocycline gel or 0.1% chlorhexidine subgingival irrigation to augment scaling and root planing in patients with moderate to advanced chronic adult periodontitis. 32 healthy patients with moderate to advanced chronic adult periodontitis were enrolled in the study. In each patient, the quadrants that had 2 or more teeth with $5{\sim}8mm$ probing pocket depth and radiographic evidence of alveolar bone loss were selected and divided into test side and control side according to the split-mouth design. All patients received standardized oral hygiene instructions at the beginning of the study and all remaining teeth received scaling and root planing until 0 week. The 2% minocycline gel was applied to periodontal pocket at 0, 1, 2, 3 week in the test side. The 0.1% chlorhexidine solution and the normal saline were irrigated subgingivally for about 30 seconds in the positive control side and negative control side respectively. The clinical and microbiological analysis carried out at 0, 4, 8, and 12 weeks . The results of this study were as follows; 1. In saline irrigation group, there was no adjunctive effects in probing pocket depth reduction, sulcular bleeding index and no significant changes in relative proportions of subgingival bacteria. 2. The chlorhexidine irrigation as an adjunct to scaling and root planing results in reduction in the plaque index and sulcular bleeding index, but there was not statistically significant. The relative proportion of spirochetes was significantly reduced, but the proportion of motile rods was no significant reduction. 3. The minocycline gel delivered subgingivally as an adjunct to scaling and root planing provide significant benefit in reducing probing depths and sulcular bleeding index compared to saline and chlorhexidine irrigation groups. 4. The relative proportions of spirochetes and motile rods were significantly reduced and the proportions of cocci and non-motile bacteria were correspondingly increased in the minocycline gel group. In conclusion, minocycline gel delivered subgingivally as an adjunct to scaling and root planing induces clinical and microbial responses more favorable for periodontal health than saline and chlorhexidine subgingival irrigation.

• Smart Structures and Systems
• /
• 제7권1호
• /
• pp.1-13
• /
• 2011

It has been shown in the literature that active adjustment of the intake area of a jet engine has potential to improve its fuel efficiency. This paper presents the design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators. The Nitinol SMA material is used in this research due to its advantages of high power-to-weight ratio and electrical resistive actuation. The Nitinol SMA material can be fabricated into a variety of shapes, such as strips, foils, rods and wires. In this paper, SMA wires are used due to its ability to generate a large strain: up to 6% for repeated operations. The proposed proof-of-concept engine intake employs overlapping leaves in a concentric configuration. Each leaf is mounted on a supporting bar than can rotate. The supporting bars are actuated by an SMA wire actuator in a ring configuration. Electrical resistive heating is used to actuate the SMA wire actuator and rotate the supporting bars. To enable feedback control, a laser range sensor is used to detect the movement of a leaf and therefore the radius of the intake area. Due to the hysteresis, an inherent nonlinear phenomenon associated with SMAs, a nonlinear robust controller is used to control the SMA actuators. The control design uses the sliding-mode approach and can compensate the nonlinearities associated with the SMA actuator. A proof-of-concept model is fabricated and its feedback control experiments show that the intake area can be precisely controlled using the SMA wire actuator and has the ability to reduce the area up to 25%. The experiments demonstrate the feasibility of engine intake area control using an SMA wire actuator under the proposed design.

• 시스템엔지니어링학술지
• /
• 제12권2호
• /
• pp.115-125
• /
• 2016

An improved RRS (Reactor Regulating System) logic is implemented in this work using systems engineering approach along with GA (Genetic Algorithm) deemed as providing an optimal solution to a given system. The current system works desirably and has been contributed to the safe and stable NPP operation. However, during the ascent and decent section of the reactor power, the RRS output reveals a relatively high steady state error and the output also carries a considerable level of overshoot. In an attempt to consolidate conservatism and minimize the error, this research proposes applying genetic algorithm to RRS and suggests reconfiguring the system. Prior to the use of GA, reverse-engineering is implemented to build a Simulink-based RRS model and re-engineering is followed to apply the GA and to produce a newly-configured RRS generating an output that has a reduced steady state error and diminished overshoot level.

• Structural Engineering and Mechanics
• /
• 제51권6호
• /
• pp.1005-1016
• /
• 2014

Roles of reactor internals are to support nuclear fuel, provide insertion and withdrawal channels of nuclear fuel control rods, and carry out core cooling. In case of functional loss of the reactor internals, it may lead to severe accidents caused by damage of nuclear fuel assembly and deterioration of reactor vessel due to attack of fallen out parts. The present study is to examine fluid flows in reactor internals subjected to hydrodynamic loads. In this context, an integrated model was developed and applied to two kinds of numerical analyses; one is to analyze periodic loading effect caused by pump pulsation and the other is to analyze random loading effect employing different turbulent models. Acoustic pressure distributions and flow velocity as well as pressure and temperature fields were calculated and compared to establish appropriate analysis techniques.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.1893-1894
• /
• 2006

본 논문은 원자로 제어봉구동장치 각 기구의 동작을 감시하여 이 장치에 의한 제어봉의 이동 여부를 검출하는 방법에 관한 것이다. 제어봉구동장치의 일부에서 전기적, 기계적 결함이 생기면 제어봉의 스텝 이동이 제대로 수행되지 못하고, 결국 해당 제어봉은 원자로의 목표 열적 출력을 위한 바른 위치에 도달하지 못하게 된다. 이렇게 되면 제어봉들 사이에 위치 편차가 발생하여 원하는 원자로 열적 출력을 얻을 수 없게 되므로 제어봉구동장치 각 기구의 동작을 신속하고 정확하게 파악하여 해당 제어봉의 이동 여부를 검출할 수 있어야 한다. 제어봉구동장치의 기구들은 각자의 여자 코일의 전류 파형 변화를 통해 동작 여부를 확인할 수 있는데 본 논문에서는 코일 전류 파형을 분석하기 위하여 국소적인 왜곡 검출 능력이 우수한 웨이블릿 변환 기법을 사용하였다.

• Journal of Welding and Joining
• /
• 제10권4호
• /
• pp.240-249
• /
• 1992

The objective of this study is to investigate the characteristics of welded joints on the Zircaloy-4 resistance upset welding for HWR(Heavy Water reactor)fuel rods. To estimate the characteristics of welded joints, the various tests were performed on the test coupons systematically with a wide range of each welding parameters in terms of a tensile test, burst test, knoop hardness test and metallography. Major results obtained in this study are as follows: 1. The tube and machined with 120.deg. projection was the reliable weld joint design for the nuclear fuel rod end cap welding. 2. As the weld current and the amount of upset increased linearly with increasing welding main heat input, it could make an estimate of their variation in accordance with the phase shift control. 3. It was found that an increase in squeeze force has an effect on the upset contour of welded joint because the amount of upset were increased by the change of squeeze force.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.162-166
• /
• 2003

In combined forward-backward extrusion with controlled forward speed by a counter punch, accurate parts with forward rod can be formed. As an extension of this method, reverse extrusion is proposed, in which the extruded forward rod is pushed back while the main punch is kept at the final position after the forward-backward extrusion process. The experiment is carried out using lead as a model material. With the reverse extrusion method, longer forward rods can be formed without under-filling defect than that by combined extrusion with controlling extrusion speed.