• Journal of Bio-Environment Control
• /
• v.9 no.4
• /
• pp.201-206
• /
• 2000

A certain system to overcome high temperature should be introduced for the stable year-round cultivation in greenhouses. There are efficient methods to overcome high temperature such as ventilation system with shading screen, fan and pad system with screen, and fog system with screen. This study was carried out to find a means to determine the capacity of such system. Heat balance equations for each system were established and verified by experimental results. The calculated ventilation rates from heat balance equations showed a good agreement with the measured ones. The evapotranspiration coefficient was the most important parameter affecting the ventilation requirement among input parameter affecting the ventilation requirement among input parameters except weather data. When the evaportanspiration coefficient increased 1%, the ventilation requirement decreased 1.3%. Therefore the data of evapotranspiration coefficient should be accumulated by various experiments, and then design standards and selection guidelines should be provided. The simulation results for same design conditions shown that air exchanges requirement and evaporating water of fan and pad system were 5.1∼7.7% and 6.8∼9.3% larger than those of fog system, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.241-241
• /
• 2012

Semiconductor industry has been taking the advantage of improvements in process technology in order to maintain reduced device geometries and stringent performance specifications. This results in semiconductor manufacturing processes became hundreds in sequence, it is continuously expected to be increased. This may in turn reduce the yield. With a large amount of investment at stake, this motivates tighter process control and fault diagnosis. The continuous improvement in semiconductor industry demands advancements in process control and monitoring to the same degree. Any fault in the process must be detected and classified with a high degree of precision, and it is desired to be diagnosed if possible. The detected abnormality in the system is then classified to locate the source of the variation. The performance of a fault detection system is directly reflected in the yield. Therefore a highly capable fault detection system is always desirable. In this research, time series modeling of the data from an etch equipment has been investigated for the ultimate purpose of fault diagnosis. The tool data consisted of number of different parameters each being recorded at fixed time points. As the data had been collected for a number of runs, it was not synchronized due to variable delays and offsets in data acquisition system and networks. The data was then synchronized using a variant of Dynamic Time Warping (DTW) algorithm. The AutoRegressive Integrated Moving Average (ARIMA) model was then applied on the synchronized data. The ARIMA model combines both the Autoregressive model and the Moving Average model to relate the present value of the time series to its past values. As the new values of parameters are received from the equipment, the model uses them and the previous ones to provide predictions of one step ahead for each parameter. The statistical comparison of these predictions with the actual values, gives us the each parameter's probability of fault, at each time point and (once a run gets finished) for each run. This work will be extended by applying a suitable probability generating function and combining the probabilities of different parameters using Dempster-Shafer Theory (DST). DST provides a way to combine evidence that is available from different sources and gives a joint degree of belief in a hypothesis. This will give us a combined belief of fault in the process with a high precision.

• Analytical Science and Technology
• /
• v.16 no.6
• /
• pp.488-498
• /
• 2003

By LC/MS/MS, the analytical method of sildenafil and its analogues (homosildenafil, vardenafil and tadalafil) used as used medical treatment of impotence was established. electrosprary ionization (ESI) and atmospheric pressure chemical ionization (APCI) as a ionization method were applied. Several parameter were varied and the sensitivity and reproducibility were compared. In LC/ESI-MS method, capillary voltage, cone voltage, extractor, entrance and RF lens to create appropriate productr ions for multiple reaction monitoring (MRM) were variable parameter, but the formation of the other product ions except the precursor ion could not detect. And the value of entrance, collision energy, exit, corona voltage, cone voltage, extractor, RF lens, cone gas, and desolvation gas in APCI mode were varied, only the creation pattern of fragment ions by the change of RF lens value were detected, and the limit of detection was decreased due to the increase of S/N. Ten millimole ammonium formate (pH 4.8):acetonitrile=70:30 by isocratic elution in HPLC system was shown the maximum sensitivity in MS, the detection limit of sildenafil, homosildenafil, vardenafil and tadalafil obtained by ESI-MRM were 0.10, 0.025, 0.025, and $0.25{\mu}g/mL$ at S/N>5, respectively.

• Journal of Bio-Environment Control
• /
• v.13 no.1
• /
• pp.1-7
• /
• 2004

This study is kinematics for the manipulator development of cucumber harvesting. A theory value was verified by repeated error measurement after the forward kinematics or inverse kinematics analysis of manipulator. Manipulator is consisted of one perpendicular link and two revolution link. The transformation of manipulator can be valued by kinematics using Denavit-Hartenberg parameter. The value of inverse kinematics which is solved by three angles faction shows two types. Repeated errors refered maximum 2.60 mm, 2.05mm and 1.55 mm according to X, Y, Z axis. In this study, the actual coordinates of maximum point and minimum point were agreement in the forward kinematics or inverse kinematics. The results of repeated error measurement were reflect to be smaller compared to a diameter of cucumber. measurement errors were determined by experimented errors during the test. For reducing errors of manipulator and improving work efficiency, the number of link should be reduced and breeding and cultural environment should be considered to reduce the weight and use the hard stuff. The velocity of motor for working should be considered, too.

• Journal of Bio-Environment Control
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2001

Fruit growth in kiwifruit shows double sigmoid curve, but it does not certainly indicate as years. Therefore, I though the reason to be easy to the effect of water state change in kiwifruit, investigated diurnal change in water status of fruit tissues with an isoipiestic psychrometers against the fruit growth stage of kiwifruit in 1995 and 1996. Diurnal change in the fruit tissue water potential were little, but violent for fruti growth state III in 1996. The potential of two years dropped gradually approach to harvest time. On the other hand, osmotic potential of the tissues indicated to very similar to water potential, dropped rapidly -1.5MPa before dawn, recovered -1 MPa after 3 h on October 14, were -1~-1.7 MPa at the fruit commercial harvest in 1995. It had a tendency to lower in 1996 than in 1995. It was recorded to the minimum air temperature at the first for an autumn in 1995; 13$^{\circ}C$ from the middle night of October 13 to dawn of October 14. Leaves water potential, which is related to water status of xylem, nearly fell below -1 MPa at before dawn from stage II in 1996. However, it fell so low only at commercial in 1995. At the stage II, osmotic potential and ascent of the turgor pressure was high than 1995-fruit. There parameter suggested that three of kiwifruit in 1996 were status of water stress for stage III. The results from this study indicated that difference of fruit growth between 1995-fruit and 1996-fruit was affected by water status of the fruit tissues, which was influenced by weather condition.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.515-525
• /
• 2016

Parameter analysis of a pretension girder bridge for urban maglev transit was performed to identify the main design parameters and their effect. Girder deflection at mid-span is the most important design criteria of urban maglev transit. Therefore, concrete compressive strength, girder height, girder length, and unbonded tendon length were selected as the design parameters that relate to girder deflection. In addition, tendon layout and unbonded tendon ratios were also considered as design parameters to control the top stress of the pretension girder section at the support. The analysis results show that both the girder height and length are dominant design parameters governing girder deflection, more important than compressive strength and unbounded tendon length. And, sensitivity analysis makes this study suggest design weight value. In terms of stress, a tendon layout that can satisfy the unbounded tendon rule requires an additional tendon or rebar at the upper section to control the tensile stress on top of the section. Therefore, to improve feasibility and constructability in the future, an enhanced unbonded tendon rule considering the load characteristics of the urban maglev system should be studied.

• Journal of Environmental Impact Assessment
• /
• v.29 no.6
• /
• pp.403-413
• /
• 2020

A mathematical model comprised with eight simultaneous quasi-linear partial differential equations was suggested to provide optimal chlorination strategy. Upstream weighted finite element method was employed to construct multidimensional numerical code. The code was verified against measured concentrations in three type of reactors. Boundary conditions and reaction rate were calibrated for the sixteen cases of experimental results to regenerate the measured values. Eight reaction rate coefficients were estimated from the modeling result. The reaction rate coefficients were expressed in terms of pH and temperature. Automatic optimal algorithm was invented to estimate the reaction rate coefficients by minimizing the sum of squares of the numerical errors and combined with the model. In order to minimize the concentration of chlorine and pollutants at the final usage sites, a real-time predictive control system is imperative which can predict the water quality variables from the chlorine disinfection process at the water purification plant to the customer by means of a model and operate the disinfection process according to the influent water quality. This model can be used to build such a system in water treatment plants.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.11a
• /
• pp.14-17
• /
• 2010

Following the proliferation of three-dimensional video contents and displays, many terrestrial broadcasting companies prepare for starting stereoscopic 3DTV service. In terrestrial stereoscopic broadcast, it is a difficult task to code and transmit two video sequences while sustaining as high quality as 2DTV broadcast attains due to the limited bandwidth defined by the existing digital TV standards such as ATSC. Thus, a terrestrial 3DTV broadcasting system with heterogeneous video coding systems is considered for terrestrial 3DTV broadcast where the left image and right images are based on MPEG-2 and H.264/AVC, respectively, in order to achieve both high quality broadcasting service and compatibility for the existing 2DTV viewers. Without significant change in the current terrestrial broadcasting systems, we propose a joint rate control scheme for stereoscopic 3DTV service. The proposed joint rate control scheme applies to the MPEG-2 encoder a quadratic rate-quantization model which is adopted in the H.264/AVC. Then the controller is designed for the sum of two bit streams to meet the bandwidth requirement of broadcasting standards while the sum of image distortions is minimized by adjusting quantization parameter computed from the proposed optimization scheme. Besides, we also consider a condition on quality difference between the left and right images in the optimization. Experimental results demonstrate that the proposed bit rate control scheme outperforms the rate control method where each video coding standard uses its own bit rate control algorithm in terms of minimizing the mean image distortion as well as the mean value and the variation of absolute image quality differences.

• Journal of muscle and joint health
• /
• v.6 no.1
• /
• pp.100-135
• /
• 1999

Typical symptoms of rheumatic disease affect overall daily living and cause severe stress. Individuals afflicted with rheumatic disease have many illness-related stresses. Pain was the predominantly perceived stress followed by limitation in mobility, difficulties in carrying out activities of daily living. helplessness, dependency on others, threat to self-esteem, interference in social activity, interference in family relationships. difficulties performing at work, and discomfort of the treatment. Patients with chronic arthritis are subjected to long periods of continuous stress, which may require the management by the health care provider. In these cases, the purpose of the nursing is helping to promote health through supporting patient's coping. Therefore, for the nursing intervention to be effective, it is critical to build a theoretical framework that describes stress-coping for chronic arthritis. Thus, the purpose of this dissertation is to present a theoretical framework which describes the stress-coping processes and to empirically test pathos of this framework for the people with chronic arthritis. The foundation upon which this framework is built in the Erickson, Tomlin, and Swain(1983) theory of Modeling and role-Modeling. The subjects were 275 patients with rheumatoid arthritis or osteoarthritis who visited the outpatient clinic. A hypothetical model of stress-coping was tested by covariance structure analysis with PC-LISREL 8.12 program. As a result, the overall fit was good(Chi-square=94.49, P=0.00, RMR=0.067, GFI=0.95, AGFI=0.91, NNFI=0.93, NFI=0.91) for the hypothetical model. The results of hypothesis testing were as follows : Basic need satisfaction had a statistically significant influence on illness-related experience, emotional stress and coping resources. Internal health locus of control had a statistically significant influence on coping resources. However, independent variables(basic need satisfaction, internal health locus of control, illness-related experience, emotional stress and coping resource) did not have significantly influence on coping. And then, the hypothetical model was modified by considering both the theoretical implication and statistical significance of the parameter estimates. The revised model had a better fit to the data(Chi-square=83.11(P=0.00), RMR=0.061, GFI=0.96, AGFI=0.92, NNFI=0.95, NFI=0.92). Hypothesis emerged from the revised model was tested. The results of hypothesis testing were as follows : Basic need satisfaction had a statistically significant influence on illness-related experience, emotional stress and coping resources. Internal health locus of control had a statistically significant influence on illness-related experience and coping resources. Internal health locus of control, illness-related experience, emotional stress and coping resources had a significantly influence on coping. According to the results of this dissertation, basic need satisfaction and internal health locus of control play a central role in appraisal of illness-related experience and coping resources. And illness related-experience, emotional stress, and coping resources affect on coping activities. In summary, nursing interventions to enhance basic need satisfaction and internal health locus of control will decrease illness related experience and emotional stress and increase coping resources. Increased coping resources will prompt coping activities.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.584-593
• /
• 2018

The highly efficient operation of induction motors has been studied in the past years. Among the many attempts made to obtain highly efficient operation, Maximum Torque Per Amp (MTPA) controls in induction motor drives were proposed. This method enables induction motor drives to operate very efficiently since it achieves the desired torque with the minimal stator current. This is because the alternate qd induction motor model (AQDM) is a highly accurate mathematical model to represent the dynamic characteristics of induction motors. However, it has been shown that the variation of the rotor resistance degrades the performance of the MTPA control significantly, thus leading to its failure to satisfy the maximum torque per amp condition. To take into consideration the mismatch between the actual value of the rotor resistance and its parameter value in the design of the control strategy, an adaptive MTPA control was proposed. In this work, this adaptive MTPA control is investigated in order to achieve the desired torque with the minimum stator current at multiple operating points. The experimental study showed that (i) the desired torque was accurately achieved even though there was a deviation of the order of 5% from the commanded torque value at a torque reference of 25 Nm (tracking performance), and (ii) the minimum stator current for the desired torque (maximum torque per amp condition) was consistently satisfied at multiple operating points, as the rotor temperature increased.