• Structural Engineering and Mechanics
• /
• v.26 no.5
• /
• pp.557-568
• /
• 2007

The elastic T-stress is increasingly being recognized as an important second parameter to the stress intensity factor for fracture and fatigue assessments. In this paper, the mutual or M-contour integral approach is employed in conjunction with the Boundary Element Method (BEM) to determine the numerical T-stress solutions for cracks in plates with multiple holes. The problems investigated include plates of infinite width with multiple holes at which single or double, symmetric cracks have grown from. Comparisons of these results are also made with the corresponding solutions of finite plates with a single hole. For completeness, stress intensity factor solutions for the cracked geometries analyzed are presented as well. These results will be useful for failure assessments using the two-parameter linear elastic fracture mechanics approach.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.4 s.23
• /
• pp.136-145
• /
• 2005

특이응력해석을 위한 일반화된 가역상반일 경계적분식이 섬유강화복합재를 모형화한 직교 이방성 크랙평판의 수치해를 위하여 발전시켰다. 이 적분방정식은 평판경계에서의 탄성변위와 트랙션의 변수로 구성된 경계적분식의 형태로 하중이 없다는 두 크랙면의 경계조건과 유한의 탄성변형에너지의 개념에서 경계적분식에 필요한 특성해를 규정하고 대응되는 보조해를 계산하였다. 대칭모우드 I형의 중앙원공크랙평판 및 복합모우드형의 반원편측크랙 일단고정평판의 응력확대계수가 임의의 섬유방향각에 따라서 계산되었다.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.237-248
• /
• 2000

Based on the preliminary results from the therm analysis, which is currently carrying, three-dimensional computer simulations using a finite element code, ABAQUS Ver. 5.8, were designed to determine the mechanically stable cavern and deposition hole spacing. Linear elastic modeling for the cases with different cavern and deposition hole spacing were carried out under three different in situ stress conditions. From the simulations, the response of the rock to the stress redistribution after the excavation of the openings could be investigated. Also the optimum cavern and deposition hole spacing could be estimated based on the factor of safety. When the in situ stress determined from the actual stress measurements in Korea were used, the case with cavern spacing of 40m and deposition hole spacing of 3m was in very stable condition, because the factor of safety was calculated as 3.42., When the in situ stress conditions for Sweden and Canada were used, the previous case, they seem to be in stable condition, since the factors of safety are still higher than 1.0. From these results, it was concluded that the rock will not fail even after the stress redistribution.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.439-449
• /
• 2002

Experimental investigations of the flow structure and heat transfer enhancement in a channel with a built-in circular cylinder and a wing-let type vortex generator are presented. Without any vortex generators, relatively low heat transfer takes place in the downstream of the circular cylinder where is a recirculation region with low velocity fluid is formed. However with a wing-let type longitudinal vortex generator in the wake region behind the cylinder, heat transfer in the region can be enhanced. In order to control the strength of longitudinal vortices, the angle of attack of the vortex generators is varied from $20^{circ} to 45^{\circ}$, but spacings between the vortex generations are fixed to be 5 mm. The 3-dimensional mean velocity field downstream of the vortex generator is measured by a five-hole pressure probe, and the hue-capturing method using thermochromatic liquid crystals has been used to provide the local distribution of the heat transfer coefficient. The vorticity field and streamwise velocity contour are obtained from the velocity field. Streamwise distributions of averaged Stanton number on the measurement planes show very similar trends for all the experimental cases($\beta=20^{circ}, 30^{circ} and 45^{\circ}$). Circulation strength and heat transfer coefficient have the maximum values when the angle of attack($\beta$) is $30^{\circ}$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.83-87
• /
• 2012

Computational Fluid Dynamics (CFD) method has been used to investigate the axial force of automotive water pump. As the excessive axial force can make some unexpected problems like impeller interference and coolant leakage we have focused on finding the cause of axial force and its reduction in this paper. First, we have tested the closed type water pump with and without balance hole by the calculation methods. By examining the pressure contour around the impeller, we have found that the axial force arises not only from the pressure difference around shroud but also from the pressure difference around hub. So we have tested two impellers - one is normal open type impeller and the other is open type impeller with modified hub. The results show that the axial force reduction is about 150~200N for normal one and 700N@3000RPM for modified impeller. And the hydraulic efficiency which is important in aspect of engine fuel efficiency is reduced about 6.5% for normal one but increased 4%@3000RPM for modified impeller.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.33-39
• /
• 2008

To improve the mixing efficiency and to reduce the pressure loss, it is needed to develope a new mixing device for supersonic combustion. The vent mixer is introduced as the new supersonic fuel-air mixer. Computational analyses, that include pressure profile, density contour, and streamline tracing, have been carried out. The expansion wave generates at the end of the extended upper wall of the mixer. And it reduces the shock wave from the hole. Incoming air flow through the hole makes several recirculation regions which increase the mixing efficiency, and the separation region at the downward wall expends the boundary layer which reduces the pressure loss.

• Explosives and Blasting
• /
• v.37 no.3
• /
• pp.25-33
• /
• 2019

Controlling the blast-induced damage zone(BDZ) in mining excavation is a significant issue for the safety of employees and the maintenance of facilities. Numerous studies have been conducted to accurately predict the BDZ in underground mining. This study employed the dynamic fracture process analysis (DFPA) to estimate the BDZ from a single hole blasting. The estimated BDZ were compared with the results obtained by Swedish empirical equation. The DFPA was also used to investigate the control mechanism of BDZ and fracture plane formation around perimeter holes for underground mining blasting.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.772-778
• /
• 2003

Polystyrene foam is easily melted and vapoured by heat, has a proper quality in the pattern manufacturing and has a low price. The objective of this study is to develop a rapid prototyping method fur polystyrene foam pattern manufacuring to use the eliminative pattern casting (EPC). Applying fur the rapid prototyping concept reversely, the unnecessary part of section is vapored away by heat source of laser beam. In order to examine the applicability between laser beam process and polystyrene foam material, the basic experiments such as hole, line, plane and contour process are carried out. With these results, various three-dimensional shape patterns are made and this rapid prototyping tool for polystyrene foam manufacturing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1085-1088
• /
• 2001

The process of styrofoam pattern that has been used for material of press die pattern depends chiefly on handwork. Laser manufacturing system developed to increase precision and efficiency of process that is also able to convert the design easily. Applying the RP(rapid prototyping) concept reversely, the unnecessary part of section is vapored away by heat source of laser beam after converting 3-D CAD model into cross-sectional shape information. Laser beam is line-scanned in plane specimens to measure the depth and width of cut, surface roughness, cross-sectional shape as converting laser power, scanning speed, cutting gas pressure. With these basic data, plane surface, inclined surface, hole, outer contour trimming process is experimented and optimum condition are obtained. In plane and inclined surface experiments, 15W laser power and 50mm/s scanning speed make superior processing property and 30W, 10mm/s make processing efficiency increase in trimming process. With these results, simple patterns were manufactured and the possibility of applying laser manufacturing system to styrofoam pattern was convinced.

• Journal of Mechanical Science and Technology
• /
• v.16 no.5
• /
• pp.655-665
• /
• 2002

Two-dimensional elastic analysis of doubly periodic circular holes in an infinite plane is given in this paper. Two cases of loading, remote tension and remote shear, are considered. A rectangular cell is cut from the infinite plane. In both cases, the boundary value problem can be reduced to a complex mixed one. It is found that the eigenfunction expansion variational method is efficient to solve the problem. Based on the deformation response under certain loading, the notched medium could be modeled by an orthotropic medium without holes. Elastic properties for the equivalent orthotropic medium are investigated, and the stress concentration along the hole contour is studied. Finally, numerical examples and results are given.