• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.561-571
• /
• 1999

Microstructure and mechanical properties of five Cr-Mo steels for nuclear industry applications have been investigated. Transmission electron microscopy, energy dispersive spectrometer, differential scanning calorimeter, hardness, tensile, and impact test were used to evaluate the Cr and W effect on the microstructure and mechanical properties. Microstructures of Cr-Mo steels after tempering are classified into three types : bainitic 2.25Cr-lMo steel, martensitic Mod.9Cr-lMo, HT9M, and HT9W steels, and dual phase HT9 steel. The majority of the precipitates were found to be M$_{23}$C$_{6}$ carbides. As minor phases, fine needle-like V(C,N), spherical NbC, fine needle-like Cr-rich Cr$_2$N, and Cr-rich M$_{7}$C$_3$were also found. Addition of 2wt.% W in Cr-Mo steels retarded the formation of subgrain and dissolution of Cr$_2$N precipitates. Hardness and ultimate tensile strength increased with increasing Cr content. Though Cr content of HT9W steel was lower than that of HT9 steel, the hardness of HT9W was higher due to the higher W content. W added HT9W steel had the highest ultimate tensile strength above $600^{\circ}C$. But impact toughness of W added steel (HT9W) and high Cr steel (HT9) was low.w.w.

• 펄프종이기술
• /
• 제30권1호
• /
• pp.29-43
• /
• 1998

This study was to investigate the effect of .compressive load and cyclic humidity(2$0^{\circ}C$, 65% and 90% RH) on the physical and mechanical properties of corrugated board. Corrugated boards in the study were under compressive load and under cyclic humidity, and their properties were compared to those without load. Results were summarized as follows ; 1 Statistically significant correlation was shown between the ring crush of the boards and the compressive strength of cylinder specimen made from the boards. So we could study the compressive behavior of board with cylinder specimen. 2. The boards under the compressive load increased their moisture content and thickness much more than those without load both in constant and in cyclic RH. 3. The compressive and tensile strength of board samples were inversely and closely proportional to the sheet moisture content regardless of their load and humidity history. 4. The moisture content did not show any significant proportionality to the change of burst strength of boards within this experiment. 5. Board reconditioning in standard condition led to the recovery of the strength loss that had occurred under various load and humidity condition. 6. The handsheets prepared from the boards that had experienced compressive load and cyclic humidity, and those with no-load and 65% RH did not show any significant difference in strength properties. No physical damage or load-carrying properties of the wood fiber were observed by the compressive load and cyclic humidity history.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.43-49
• /
• 2006

The surface and pore structure of cellulose fibers have a significant impact on the properties and performance in applications. Cellulase enzymatic hydrolysis of cellulose fibers can result in changes to the surface and pore structure thus providing a useful tool for fiber modification. This research characterizes these changes using various test methods such as fiber dimension, water retention value, hard-to-remove water content, freezing and non-freezing bound water content, polymer adsorption, and crystallinity index. For a high-dosage enzyme treatment (0.10 g/g), the fiber length was significantly decreased and the fibers were 'cut' in the cross direction, not in the axial direction. The swelling capacities as measured by the WRV and HR water content increased for the high-dosage treatment. Three independent measurements (non-freezing bound water, polymer adsorption, and crystallinity index) are in good agreement with the statement that the amorphous regions of cellulose fibers are a more readily available substrate relative to crystalline regions. Based on the experimental results obtained herein, a model was proposed to explain surface and pore structure modification of cellulose fibers via enzymatic treatment.

• 한국콘텐츠학회논문지
• /
• 제13권2호
• /
• pp.71-80
• /
• 2013

이 연구는 PP(방송채널사용사업) 현황을 진단하고, 특히 독립 PP의 실상을 구체적으로 파악하고자 이루어졌다. 이를 위해 14개 독립 PP를 선정하여 심층인터뷰를 진행하였으며, 독립 PP의 문제를 경영, 제작, 콘텐츠의 세 측면에서 분석하였다. 연구결과 독립 PP는 MPP에 비해 경영, 제작, 콘텐츠 모두에서 열악한 위상을 가지고 있음을 발견하였다. 독립 PP의 경영 구조는 매우 취약하였으며, 제작 환경도 좋지 않았다. 독립 PP들은 콘텐츠 제작 및 구매도 어려운 환경에 놓여 있으며, 지상파 재방 콘텐츠에 의존하는 등 제작보다는 유통에 치중하고 있는 실정이었다. 이는 PP시장의 불균형을 심화시키고, 궁극적으로는 한국의 콘텐츠 산업의 발전에 부정적인 결과를 초래하게 된다. 따라서 독립 PP의 위상을 높이기 위한 방안이 강구되어야 한다.

• 펄프종이기술
• /
• 제45권4호
• /
• pp.27-33
• /
• 2013

Manufacturing fabrics from dissolving cellulosic pulp is increasing in these days. For making high quality of cellulose-based fabrics, control of cellulose DP (degree of polymerization), its alpha cellulose content, its brightness, and its crystallinity are important. To process the cellulosic raw material, refining of cellulosic fibers is essential, and it is important to know if refining affects those important cellulose properties. The effects of PFI mill and Valley beater refining on the alpha-cellulose content, cellulose DP, crystallinity, and paper mechanical properties of wood and two different cotton fibers were studied. The results showed that PFI mill refining rarely affected those properties. Fibers refined by a Valley beater displayed a small reduction in fiber length in comparison with those refined by a PFI mill. However, the Valley beater refining method produced almost no changes in cellulose properties, either. The refining process seemed to have very little effect on the cellulose DP, crystallinity index, or alpha-cellulose content until the freeness decreased to around 300 mL CSF for wood and 100 mL CSF for cotton fibers, respectively. There were also no differences in tensile strength development in two refining methods.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.32-38
• /
• 2014

There has been increasing demand to the eco-friendly materials such as phytoncide which is extracted to plants in the textile industry, recently. It is interesting that alginic acid sodium salt(Alg-Na) is used to eco-friendly binder for the functional capsule finishing. In this study, we made PEO/Alg-Na blend solutions of various ratio and observed the changing binding property of the blend solutions according to PEO contents through FT-IR, DSC, contact angle, peel strength, etc. The viscosity of Alg-Na/PEO blend solutions increased with increase of contents and the viscosity quickly increased with increase of PEO content in Alg-Na 5% content, specially. It is shown that the hydrogen bond peak by blend of Alg-Na and PEO found through FT-IR analysis but the peak decreased in PEO above 60% content. And the peel strength was predominant in PEO 50% ratio.

• 한국의류학회지
• /
• 제36권7호
• /
• pp.703-713
• /
• 2012

This study analyzed the physical properties and flame retardancy of Tencel FR/Cotton complex knit fabrics in order to satisfy two aspects of eco-friendliness and functionality. The flame retardant (FR) treatment of complex knit fabrics was applied by a pad-dry-cure method for additional functionality. Tensile strength, extension, bursting strength, LOI, and flame retardancy were measured by the KS (Korean Standard) K manual. The hand value knit fabrics were measured by KES-FB system. Subsequently, tensile strength and extension of wale and tensile strength of course increased in tandem with the Tencel FR yarn content. Tencel FR/Cotton complex knit fabrics were suitable for summer-weight and for baby clothes through the KES-FB system measurements. The bursting strength of Tencel FR/Cotton complex knit fabrics decreased as the contents of the Tencel FR increased; in addition, LOI increased as the contents of Tencel FR increased. This was due to the Tencel FR flame resistance function; however, the tensile strength decreased. The optimum fiber content of Tencel FR/cotton content was 1:1. The optimum conditions of flame retardant treatment were a treatment temperature $130^{\circ}C$ and the concentration of finishing agent and assistance binder (AR4260) was 35% and 1%, respectively.

• 한국의류산업학회지
• /
• 제22권4호
• /
• pp.515-522
• /
• 2020

This study examined the effect of the blend ratio of wool and polyester fibers, yarn and fabric structural parameters to the appearance property and the formability of worsted fabrics. The mechanical properties of twenty types of manufactured worsted and PET/wool blend fabrics were measured using KES-FB and FAST systems. Garment formability increases with the thickness and cover factor as well as increases with wool content. The correlation between KES-FB and FAST system showed a relatively high correlation with an extensibility of 0.98, bending and shear rigidity 0.71; both were higher than polyester synthetic fiber. The correlation coefficient of garment formability between KES-FB and FAST systems was 0.93 and the correlation coefficient between formability and fabric extensibility was 0.8. These results were higher than those of bending and shear rigidity. This revealed that garment formability was influenced by wool content, cover factor and fabric thickness; however, wool content and fabric thickness were the most important factors for the seam pucker. The garment formability of the worsted fabrics can be predicted by fabric mechanical properties measured from KES-FB and FAST systems.

• 펄프종이기술
• /
• 제37권5호통권113호
• /
• pp.50-55
• /
• 2005

In previous report, we investigated the impact of hexeneuronic acid and some residual extractiveson lignin determination. These non-lignin components severely interfered lignin content determination which also affect on the oxygen delignification comparison between aspen and pine unbleached kraft pulps. Very different pattern was observed whether based on uncorrected conventional kappa number or based on corrected kappa number in oxygen delignification comparison. Lower kappa number aspen pulps showed poor response to oxygen delignification when kappa number was used as lignin determination method but better response with using the acid lignin method. Phenolic hydroxyl group in kraft pulps were also compared based on uncorrected or corrected kappa numberfor lignin content. Based on uncorrected kappa number, lower kappa number oxygen-delignified pulps had lower phenolic hydroxyl group. However, lower kappa number oxygen-delignified pulps showed much higher phenolic hydroxyl group based on the corrected lignin content. For accurate comparison for residual lignin properties from different pulps, lignin determination should be corrected from non-lignin components contribution to lignin.

• 펄프종이기술
• /
• 제43권1호
• /
• pp.74-82
• /
• 2011

The bast fiber of Paper mulberry has been generally used as a fibrous raw material in traditional Hanji-making. Nowadays, its uses is expanded to different special purposes such as paper mulberry yarn, laminated paper, antimicrobial paper depending on its application. Despite the wide array of the use of mulberry fibers, it is still limited due to some difficulties in the automation process of manufacturing works. This study is focused on the analysis of chemical components and morphological properties of paper mulberry bark for the automation of bark peeling process. The bast tissue of paper mulberry was separated in three plies; black outer layer, green inner layer, and white inner layer. The total lignin content, holocelluloses, extractives and ashes, and the anatomical structure of the three layers in mulberry bark tissue were investigated. The analysis showed that the black outer layer is composed of about 50% of total lignin content, whereas the white inner layer is composed of about 90% of holocellulose content.