• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.125-132
• /
• 2011

The dynamic characteristics of valve train are responsible for the dynamic performances of engine. We derived the equation of motion for 6 degrees of freedom model of the valve train. Computer model is also developed with flexible multibody model considering contact between components. The simulation results with these two models are compared with experimental results. We investigated the effect of the two spring models, TSDA (Translational Spring Damper Actuator) element and flexible body model, on the valve behavior and spring force. It is found that the dynamic behavior of the two models are not very different at normal operational velocity of the engine. By modeling contact between cam and tappet, the stress distributions of the cam were found. Using stress distribution obtained, contact width and contact stresses of the cam surface were calculated with Hertz contact theory.

• Structural Engineering and Mechanics
• /
• v.21 no.2
• /
• pp.205-220
• /
• 2005

This paper presents the possibilities of adapting artificial neural networks (ANNs) to predict the dimensionless parameters related to the maximum contact pressures of an elasticity problem. The plane symmetric double receding contact problem for a rigid stamp and two elastic strips having different elastic constants and heights is considered. The external load is applied to the upper elastic strip by means of a rigid stamp and the lower elastic strip is bonded to a rigid support. The problem is solved under the assumptions that the contact between two elastic strips also between the rigid stamp and the upper elastic strip are frictionless, the effect of gravity force is neglected and only compressive normal tractions can be transmitted through the interfaces. A three layered ANN with backpropagation (BP) algorithm is utilized for prediction of the dimensionless parameters related to the maximum contact pressures. Training and testing patterns are formed by using the theory of elasticity with integral transformation technique. ANN predictions and theoretical solutions are compared and seen that ANN predictions are quite close to the theoretical solutions. It is demonstrated that ANNs is a suitable numerical tool and if properly used, can reduce time consumed.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.594-602
• /
• 1998

The design analysis of axisymmetric, multi-stage deep drawing dies was performed using the rigid-viscoplastic finite element formulation. In the formulation the axisymmetric CFS algorithm was employed. Hill's non-quadratic normal anisotropic yield criterion and isotropic hardening rule were considered. For trial initial displacements and tool contact points. the geometric force equilibrium method was adopted. In order to see the validity of the formulation, the multi-stage deep drawing processes of shell-cylinder front part of hydraulic booster were simulated. The simulation showed good agreements with measurments and PAM-STAMP results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1352-1358
• /
• 2004

The mechanical spring is one of widely used machine elements. Among various kinds, flat-type spring loaded by a rotating pin was studied. A flat spring was simplified to a cantilever beam, and numerical analysis was attempted. Since the loading pin rotates about a separate axis from the fixed spring or vice versa, the location, direction, and magnitude of the contact force including normal contact and friction loads vary accordingly. Meanwhile, the spring is deformed substantially as the relative motion progresses. Therefore, this problem needs to be formulated taking the follower loading characteristics and geometrical non-linearity into account. Derived nonlinear differential equation was solved to yield the spring deflection, contact force and the torque to rotate the pin, and the result was compared with a finite element solution. Also, the influences of principal design parameters were studied. The proposed methodology is expected to be useful for the design of pin-loaded flat spring and the prevention of mechanical failures in the form of yielding or fatigue failure of spring or severe wear of the components.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.626-632
• /
• 2013

When a conductive rod is put within rotating axial magnet wheels arranged parallel, three-axial magnetic forces generate on the rod. In some region, the forces has a property of negative stiffness, thus they can be applied to noncontact conveyance of the rod without a control load. Apart from the passive driving, the magnet wheel should be controlled for the rod to be stayed at the still state or be moved in a specified velocity. But, because a control input is just the rotating speed of the magnet wheel, the number of input is less than that of variables to be controlled. It means that levitation force and thrust force increase at the same time for increasing wheel speed, resulting from a strong couple between two forces. Thus, in this paper, a novel method, in which the longitudinal motion of the rod is controlled indirectly by the normal motion of the rod with respect to the wheel center, is introduced to manipulate the rod without mechanical contact on space.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.772-780
• /
• 1987

The normal and tangential belt forces for two types of flat belts are measured and compared. From friction theory, ti was assumed that tangential friction is proportional to the actual contact area $A_{a}$ and $A_{a}$ is proportional to normal pressure P; i.e., $A_{a}$ .var.P$^{n}$ . For a flat belt with cloth backing, the n=2/3 is obtained for the constant of belt surface model. For a flat belt with rubber backing, the n=0.9 to n=1.0 is suggested as a surface model constant. The theoretical equation developed in this paper showed agood with the experimental results.

• Steel and Composite Structures
• /
• v.26 no.6
• /
• pp.771-791
• /
• 2018

This paper deals with the low velocity impact response and dynamic stresses of composite sandwich truncated conical shells (STCS) with compressible or incompressible core. Impacts are assumed to occur normally over the top face-sheet and the interaction between the impactor and the structure is simulated using a new equivalent three-degree-of-freedom (TDOF) spring-mass-damper (SMD) model. The displacement fields of core and face sheets are considered by higher order and first order shear deformation theory (FSDT), respectively. Considering continuity boundary conditions between the layers, the motion equations are derived based on Hamilton's principal incorporating the curvature, in-plane stress of the core and the structural damping effects based on Kelvin-Voigt model. In order to obtain the contact force, the displacement histories and the dynamic stresses, the differential quadrature method (DQM) is used. The effects of different parameters such as number of the layers of the face sheets, boundary conditions, semi vertex angle of the cone, impact velocity of impactor, trapezoidal shape and in-plane stresses of the core are examined on the low velocity impact response of STCS. Comparison of the present results with those reported by other researchers, confirms the accuracy of the present method. Numerical results show that increasing the impact velocity of the impactor yields to increases in the maximum contact force and deflection, while the contact duration is decreased. In addition, the normal stresses induced in top layer are higher than bottom layer since the top layer is subjected to impact load. Furthermore, with considering structural damping, the contact force and dynamic deflection decrees.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.939-942
• /
• 1997

In chemical mechanical polishing(CMP) there are many factors affecting the results. Temperature is one of the factors and it affects the removal rate. That is, the higher it arise, the more the material is removed. But the detailed temperature behavior is not discovered. In this study, we discover the distribution of temperature across the pad where the wafer has just been polished. And then we reveal the cause of the result in connection with the mechanical structure. In addition, we also discover the relationship of the friction force and normal force. With the result of two forces, we get the friction coefficient and obtain the contact model of the wafer and pad.

• Korean Journal of Computational Design and Engineering
• /
• v.3 no.3
• /
• pp.161-167
• /
• 1998

Cutting forces in ball-end milling of slanted surfaces are calculated. The cutting area is determined from the Z-map of the surface geometry and current cutter location. The obtained cutting area is projected onto the cutter plane normal to the Z-axis and compared with cutting edge element location. Cutting force is calculated by integration of elemental cutting forces of engaged cutting edge elements. Experiments with various slanted angles were performed to verify the proposed cutting force estimation model. It is shown that the proposed method predicts cutting force effectively for any geometry including sculptured surfaces with cusp marks and surfaces with pockets and holes.

• Journal of Biomedical Engineering Research
• /
• v.18 no.1
• /
• pp.71-78
• /
• 1997

Kinematic and kinetic studies were performed to investigate the walking characteristics on a treadmill with various slopes at the same speed of 1.25m/sec. Six different slopes of the treadmill were selected . -4%(-$2.3^{\circ}$), 0%($0^{\circ}$), 5%($2.9^{\circ}$), 10%($5.7^{\circ}$), 15%($8.6^{\circ}$), and 20%($11.3^{\circ}$). With increased slopes of the treadmill, both hip and knee flexion angles significantly increased at initial contact, and the maximum hip flexion during swing phase and the maximum knee flexion during stance phase also significantly increased Ankle dorsiflexion angle at initial contact and the maximum dorsiflexion increased with increased slopes. However, the maximum plantarflexion in early swing was slightly reduced with increased slopes. Hip extension in late stance and the maximum knee flexion in early swing was not changed sigilificantly with increased slopes. As for the vertical ground reaction force, compared to the yond level walking, both the first and the second peak forces increased, but the mid-support force decreased.