• Corrosion Science and Technology
• /
• 제3권5호
• /
• pp.198-208
• /
• 2004

Although there has been no general agreement on the mechanism of primary water stress corrosion cracking (PWSCC) as one of major degradation modes of Ni-base alloys in pressurized water reactors (PWR's), common postulation derived from previous studies is that the damage to the alloy substrate can be related to mass transport characteristics and/or repair properties of overlaid oxide film. Recently, it was shown that the oxide film structure and PWSCC initiation time as well as crack growth rate were systematically varied as a function of dissolved hydrogen concentration in high temperature water, supporting the postulation. In order to understand how the oxide film composition can vary with water chemistry, this study was conducted to characterize oxide films on Alloy 600 by an in-situ Raman spectroscopy. Based on both experimental and thermodynamic prediction results, Ni/NiO thermodynamic equilibrium condition was defined as a function of electrochemical potential and temperature. The results agree well with Attanasio et al.'s data by contact electrical resistance measurements. The anomalously high PWSCC growth rate consistently observed in the vicinity of Ni/NiO equilibrium is then attributed to weak thermodynamic stability of NiO. Redox-induced phase transition between Ni metal and NiO may undermine the integrity of NiO and enhance presumably the percolation of oxidizing environment through the oxide film, especially along grain boundaries. The redox-induced grain boundary oxide degradation mechanism has been postulated and will be tested by using the in-situ Raman facility.

• 폴리머
• /
• 제38권6호
• /
• pp.714-719
• /
• 2014

라이신과 글루코오스에서부터 제조된 카프로락탐과 모폴리논을 음이온 개환중합법을 이용하여 나일론 6-모폴리논 랜덤 공중합체를 합성함으로써 바이오매스 기반의 새로운 나일론을 제조할 수 있었으며 또한 친수성이 향상된 나일론 6을 제조할 수 있었다. 중합 조건을 적절하게 조절함으로써, 점도평균분자량 30000 g/mol과 수율 80%의 공중합체를 제조할 수 있었다. 모폴리논을 공중합 단량체로 사용함으로써 나일론 6의 친수성을 높게 향상시킬 수 있었다. 제조된 나일론 6-모폴리논 랜덤공중합체를 시차주사 열량계(DSC), 열중량 분석기(TGA), X-선 회절분석기(XRD), 점도계, 접촉각 측정기와 같은 분석방법으로 그 특성을 분석하였다.

• Applied Science and Convergence Technology
• /
• 제23권5호
• /
• pp.248-253
• /
• 2014

Air Gap Membrane Distillation (AGMD) is one of several technologies that can be used to solve problems fresh water availability. AGMD exhibits several advantages, including low conductive heat loss and higher thermal efficiency, due to the presence of an air gap between the membrane and condensation wall. A previous study by Bhardwaj found that the condensation surface properties (materials and contact angle) affected the total collected fresh water in the solar distillation process. However, the process condition differences between solar distillation and AGMD might result in different condensation phenomena. In contrast, N. Miljkovic showed that a hydrophobic surface has higher condensation heat transfer. Moreover, to the best of our knowledge, there is no study that investigates the effect of condensation surface properties in AGMD to overall process performance (i.e. flux and thermal efficiency). Thus, in this study, we treated the AGMD condensation surface to make it hydrophobic or hydrophilic. The condensation surface could be made hydrophilic by immersing and boiling plate in deionized (DI) water, which caused the formation of hydrophilic aluminum hydroxide (AlOOH) nanostructures. Afterwards, the treated plate was coated using hexamethyldisiloxane (HMDSO) through plasma-enhanced chemical vapor deposition (PECVD). The result indicated that condensation surface properties do not affect the permeate flux or thermal efficiency significantly. In general, the permeate flux and thermal efficiency for the treated plates were lower than those of the non-treated plate (pristine). However, at a 1 mm and 3 mm air gap, the treated plate outperformed the non-treated plate (pristine) in terms of permeate flux. Therefore, although surface wettability effect was not significant, it still provided a little influence.

• Applied Science and Convergence Technology
• /
• 제26권2호
• /
• pp.34-41
• /
• 2017

A 2.45 GHz microwave plasma with linear antenna has been prepared for hydrophobic and wear-resistible surface coating of carbon steel. Wear-resistible properties are required for the surface protection of cutting tools and achieved by depositing a hydrogenated amorphous carbon film on steel surface through linear microwave plasma source that has $TE_{10}-TEM$ waveguide. Compared to the existing RF plasma source driven by 13.56 MHz, linear microwave plasma source can easily generate high density plasma and provide faster deposition rate and wider process windows. In this study, $Ar/CH_4$ gas mixtures are used for hydrogenated amorphous carbon film deposition. When microwave power of 1000 W is applied, 40 cm long uniform $Ar/CH_4$ plasma could be obtained in gas pressure of 200~400 mTorr. The Vickers hardness measurement of hydrogenated amorphous carbon film on steel surface was evaluated. It was found the optimized deposition condition at $Ar:CH_4=25:25$ sccm, 300 mTorr with microwave power of 1000W and RF bias power of 100W. By deposition of hydrogenated amorphous carbon film, contact angle on steel surfaces increases from $43.9^{\circ}$ to $93.2^{\circ}$.

• 한국지반공학회논문집
• /
• 제27권11호
• /
• pp.39-45
• /
• 2011

본 연구는 글라스 비드와 고무 혼합재의 부피비와 상대적인 크기 비에 따른 열적 거동에 관해 다루고 있다. 혼합 물질의 열전도도를 측정하기 위하여 비정상면열원법이 사용되었다. 개별요소법과 열 네트워크 모델을 결합하여 입상체 모사 시료에서 입자 단위의 열전달 매커니즘을 분석하였다. 실험 및 해석의 결과는 다음과 같다. 유효 열전도도는 고무의 부피비가 증가할수록 감소한다. 두 물질의 상대적인 크기는 열 전파경로의 대부분을 결정하는 입자간 접촉상태의 공간적 구성을 지배한다. 같은 부피비를 갖는 혼합물질 중에서, 열이 잘 흐르지 않는 물질(여기에서는 고무)의 입자 크기가 큰 경우 열전달이 더 원활하게 이루어진다. 이상의 실험결과와 입자 단위의 관찰은 물질의 열적 거동이 부피비 뿐 아니라 구성 성분의 공간적인 구성에도 영향을 받음을 보여준다.

• 한국해양공학회지
• /
• 제19권5호
• /
• pp.16-25
• /
• 2005

The effect of vertical riser support system on the dynamic behaviour of a classical spar platform is investigated. Spar platform generally uses buoyancy-can riser support system, but as water depth gets deeper the alternative riser support system is required due to safety and cost issues. The alternative riser support system is to hang risers off the spar platform using pneumatic cylinders rather than the buoyancy-can. The existing numerical model for hull/mooring/riser coupled dynamics analysis treats riser as an elastic rod truncated at the keel (truncated riser model), thus, in this model, the effect of riser support system can not be modeled correctly. Due to this reason, the truncated riser model tends to overestimate the spar pitch and heave motion. To evaluate more realistic global spar motion, mechanical coupling among risers, guide frames and support cylinders inside of spar moon-pool should be modeled. In the newly developed model, the risers are extended through the moon-pool by using nonlinear finite element methods with realistic boundary condition at multiple guide frames. In the simulation, the vertical tension from pneumatic cylinders is modeled by using ideal-gas equation and the vertical tension from buoyancy-cans is modeled as constant top tension. The different dynamic characteristics between buoyancy-can riser support system and pneumatic riser support system are extensively studied. The alternative riser support system tends to increase spar heave motion and needs damper system to reduce the spar heave motion.

• 자원환경지질
• /
• 제5권4호
• /
• pp.221-229
• /
• 1972

Through the series of study on the above subjects, the following were founded. 1. Soluble silica in paddy top-soil (xppm) and maxium possible yield (y) is expressed as following equatic $y=63.97+0.425x-0.00114x^2$ It is known that soluble silica in paddy top-soil in South Korea is limited as 130ppm. 2. Gnder the present Korean condition 90% of paddy-top-soil is estimated to be short in available silica content and the country average to only 78ppm. 3. The total area of Korean paddy-top-soil is about 1,036,710 ha. All requirements of wollastonite in South Korea estimated from the equation $Y=0.94-0.033{\times}$are about 2 million M/T 4. Silicates fertilizer minerals are Bentonite, Zeolite, Wollastonite, Serpentine, and Chlorite. But Wollastonite is most economic and can be supplied to using Korea. 5. Wollastonite is formed in contact metomorphic deposits. Limestone is the country rock of wollastonite. Limestone in Korea is in Ryunchcon system, (Pre-cambrian) Okcheon system, (unknown), Great limestone series (paleozoic), Hongjum series (Paleozoic) and Kyungsang system (mesozoic) so that the zones of these limestone and igneous rock are the possible area which wollastonite can be produced. 6. According to the published geologic map (scale 1/5000), about 25 provinces will be possible area which wollastonite can be produced. In future, I believe that many possible area will be increased. 7. According to this survey at Danyang, total wollastonite resources are about 179,000 M/T and average of soluble $SiO_2$ is 29.84%. 8. According to this survey at Daijeon, total resources are about 57,600 M/T and average of soluble $SiO_2$ is 21.53%. 9. Total wollastonite resources including Danyang, Yangduk, and Daijeon are about 1,172,200 M/T. Considering possible resources, it will be over 20 million M/T and I can say that it is possible to be supply for a score.

• 한국항공우주학회지
• /
• 제37권2호
• /
• pp.175-180
• /
• 2009

이 논문은 폴리머 기반의 전기 분무 장치를 만들기 위하여 이온빔 장치를 통하여 초소수성으로 가공 된 polytetrafluoroethylene(PTFE) 노즐을 사용하였다. 초소수성 표면을 만들기 위하여, PTFE 표면은 Ar과 $O_2$를 이용한 이온빔 공정 장치를 사용하였다. 최적의 표면 공정 조건은 Ar과 $O_2$ 유량 및 에너지 단위를 변화 시켜 얻을 수 있었다. 공정된 노즐의 표면 특성을 분석하기 위하여 접촉각 측정을 수행하였고, 표면의 형태적 분석을 위해 scanning electron microscope(SEM) 그리고 atomic force microscope(AFM) 측정을 하였다. 초소수성으로 공정된 노즐을 사용함으로써 보다 안정적이고 반복적인 전기 분무가 가능함을 확인 하였으며, 공정 된 노즐의 성능을 평가하기 위하여 외팔보와 이온빔으로 표면 처리 된 노즐 그리고 레이져 변위센서를 이용하여 마이크로 스케일의 추력을 측정하였다.

• 한국농공학회논문집
• /
• 제53권1호
• /
• pp.29-36
• /
• 2011

HPAI (High pathogenic avian influenza) which is a disease legally designated as an epidemic generally shows rapid spread of disease resulting in high mortality rate as well as severe economic damages. Because Korea is contiguous with China and southeast Asia where HPAI have occurred frequently, there is a high risk for HPAI outbreak. A prompt treatment against epidemics is most important for prevention of disease spread. The spread of HPAI should be considered by both direct and indirect contact as well as various spread factors including airborne spread. There are high risk of rapid propagation of HPAI flowing through the air because of collective farms mostly in Korea. Field experiments for the mechanism of disease spread have limitations such as unstable weather condition and difficulties in maintaining experimental conditions. In this study, therefore, computational fluid dynamics which has been actively used for mass transfer modeling were adapted. Korea has complex terrains and many livestock farms are located in the mountain regions. GIS numerical map was used to estimate spreads of virus attached aerosol by means of designing three dimensional complicated geometry including farm location, road network, related facilities. This can be used as back data in order to take preventive measures against HPAI occurrence and spread.

• 한국안전학회지
• /
• 제26권3호
• /
• pp.69-74
• /
• 2011

Despite most of tasks in manufacturing, construction and agriculture, etc., were currently mechanized and automated, manual materials handling still existed in atypical working condition. In case of manual materials handling, repetitive work, inappropriate working posture, excessive force, contact stress might cause overload, which could lead to work-related musculoskeletal disorders and low back pains. On this basis, the goal of this study is to reveal the effects of various lifting postures of trunk angles and lower extremity postures on maximum holding time(MHT). Twenty two subjects were recruited from a university population. The experiment was designed by a combination of three trunk angle ($0^{\circ}$, $20^{\circ}$, $60^{\circ}$) and three lower extremity postures(straight, bent, kneeling). Before experimental trials, subjects performed MVC(maximum voluntary contraction) exertions in three trunk angles ($0^{\circ}$, $20^{\circ}$, $60^{\circ}$) to calculate 30%MVC at designated postures. In each trial, they were required to hold the handheld load(30%MVC) for a designated posture as long as they could. The results of MVC by trunk angles were measured in $0^{\circ}$ > $20^{\circ}$ > $60^{\circ}$ orders, but those of MHT measured in $20^{\circ}$ > $0^{\circ}$ > $60^{\circ}$ orders. These results showed that straight posture is the ideal working posture in work exerted a strong force for a short time, but the ability to work might be improved in the trunk angle $20^{\circ}$ in work required 30%MVC for a long time. Also, results of MVC and MHT by lower extremity postures measured in straight > bent > kneeling orders.