• Journal of the Korean Applied Science and Technology
• /
• v.40 no.1
• /
• pp.71-80
• /
• 2023

Silver paste is a valuable electrode material for electronic device applications because it is easy to handle with relatively low heat treatment. This study treated the electrode surface using an atmospheric-pressure plasma jet on the silver-paste electrode. This plasma jet was generated in an argon atmosphere using a high voltage of 5.5 to 6.5 kV with an operating frequency of 11.5 kHz. Plasma-jet may be more beneficial to the printing process by performing it at atmospheric pressure. The electrode surface becomes hydrophilic quickly and contact angle variation is observed on the electrode surface as a function of plasma treatment time, applied voltage, and gas flow rate. Also, there was no deviation in the contact angle after the plasma treatment in the large-area sample, that means a uniform result could be obtained regardless of the substrate size. The outcomes of this study are expected to be very useful in forming a stacked structure in the manufacture of large-area electronic devices and future applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.490.2-490.2
• /
• 2014

Since the general solar cells accept sun light at the front side, excluding the electrode area, electrons move from the emitter to the front electrode and start to collect at the grid edge. Thus the edge of gridline can be important for electrical properties of screen-printed silicon solar cells. In this study, the improvement of electrical properties in screen-printed crystalline silicon solar cells by contact treatment of grid edge was investigated. The samples with $60{\Omega}/{\square}$ and $70{\Omega}/{\square}$ emitter were prepared. After front side of samples was deposited by SiNx commercial Ag paste and Al paste were printed at front side and rear side respectively. Each sample was co-fired between $670^{\circ}C$ and $780^{\circ}C$ in the rapid thermal processing (RTP). After the firing process, the cells were dipped in 2.5% hydrofluoric acid (HF) at room temperature for various times under 60 seconds and then rinsed in deionized water. (This is called "contact treatment") After dipping in HF for a certain period, the samples from each firing condition were compared by measurement. Cell performances were measured by Suns-Voc, solar simulator, the transfer length method and a field emission scanning electron microscope. According to HF treatment, once the thin glass layer at the grid edge was etched, the current transport was changed from tunneling via Ag colloids in the glass layer to direct transport via Ag colloids between the Ag bulk and the emitter. Thus, the transfer length as well as the specific contact resistance decreased. For more details a model of the current path was proposed to explain the effect of HF treatment at the edge of the Ag grid. It is expected that HF treatment may help to improve the contact of high sheet-resistance emitter as well as the contact of a high specific contact resistance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.73-77
• /
• 2003

The backlight unit(BLU) is used as a light source of TFT liquid-crystalline-display (TFT-LCD) module. In this backlight unit, one of important components is the light guide, which is usually made of transparent polymers. Currently the screen-printing method is mainly used for the light guide as a manufacturing process. However, it has limitation to the flexibility of three-dimensional optical design. In the present paper a new alternative manufacturing method for the light guide with low-cost is proposed. This manufacturing method is named as direct surface forming (DSF), which is very similar to the well-known hot embossing except for partial contact between mold and substrate. The results of this new manufacturing method are presented in terms of processing condition, dimensional accuracy, productivity, etc.

• Korea-Australia Rheology Journal
• /
• v.15 no.4
• /
• pp.167-171
• /
• 2003

The backlight unit (BLU) is used as a light source of TFT liquid-crystalline-display (TFT-LCD) module. In this backlight unit, one of important components is the light guide, which is usually made of transparent polymers. Currently, the screen-printing method is mainly used for the light guide as a manufacturing process. However, it has limitation to the flexibility of three-dimensional optical design. In the present paper a new alternative manufacturing method for the light guide with low-cost is proposed. This manufacturing method is named as direct surface forming (DSF), which is very similar to the well-known hot embossing except for partial contact between mold and substrate. The results of this new manufacturing method are presented in terms of processing condition, dimensional accuracy, productivity, etc.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1382-1383
• /
• 2011

결정질 실리콘 태양전지에서 전극 형성 공정은 Voc(Open-circuit voltage), Isc(Short-circuit current), Rser(Series resistance), Rshunt(Shunt resistance), FF(Fill factor) 특성에 영향을 주기 때문에 매우 중요하다. 하지만 paste와 선 공정에서의 조건에 따라 특성이 바뀌기 때문에 소성 공정을 최적화하기는 쉽지 않다. 본 연구에서는 Gravure Off-set printing 방식을 이용하여 결정질 실리콘 기판 표면에 미세 전극 형성 공정을 하고 소성 조건 최적화를 위해 peak 온도와 ramp-up 속도를 변화시켜 각 조건별 특성을 비교하였다. Peak 온도가 커질수록, contact resistance의 감소에 따라 Rser가 줄어들었다. 본 연구를 통해 Voc는 619mV, FF는 77.9%로 측정되는 Gravure Off-set 태양전지에 최적화된 소성 공정 조건을 확보하였다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1525_1526
• /
• 2009

In this paper, we have studied the bulging phenomenon of ink-jet printed silver lines. The used silver inks are DGP-40LT-15C and DGH-55HTG of Advanced Nano Product (ANP) Company. We investigated the behavior of bulging by changing the polarity of the inks, the surface energy of substrate and droplet spacing in printing. The contact angle of the polar inks increased much more sensitively than the nonpolar ink as the surface energy of the substrate increases. In the case of the nonpolar ink, the bulging phenomenon occurred seriously as the droplet spacing decreased at the constant surface energy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1305-1307
• /
• 2007

We show that the electrical properties of organic thinfilm transistors(OTFTs) can be enhanced by controlling the morphology of interface between screen printed electrodes and gate dielectrics. Modified surface of the insulator layer($SiO_2$) affect on the interface energy of electrode on $SiO_2$ layer. Contact angle measurement and FT-IR spectrum shows that the interface is properly modified. OTFTs device with high efficiency has been realized through modification of interface layer.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.104-108
• /
• 2004

Problems of overlap errors and side-lobe printing by the design rule reduction in the lithography process using attenuated phase-shifting masks(attPSM) have been serious. Overlap errors and side-lobes can be simultaneously solved by the rule-based correction using scattering bars with the rules extracted from test patterns. Process parameters affecting the attPSM lithography simulation have been determined by the fitting method to the process data. Overlap errors have been solved applying the correction rules to the metal patterns overlapped with contact/via. Moreover, the optimal insertion rule of the scattering bars has made it possible to suppress the side-lobes and to get additional pattern fidelity at the same time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.5-6
• /
• 2006

There are typically applied on both rear and front sides of electrical contacts to the solar cell. The front contact formation is particularly sensitive to many parameters. Accordingly patterning of front grid line is an important factor of solar cells. This paper describe the electrical conversion efficiency, inclusive of shading loss that gives various spacing between front metal grid lines. In experiments with variation of spacing. It was verified that the wide spacing of grid fingers could increase the series resistance, also the narrow spacing of grid fingers also implies a grid with a higher density of grid fingers. The sunlight of incidence was more of reflection by grid fingers. In result, the short circuit current, which contribute to conversion efficiency was decreased, because maximum power input was reduced and increase the series resistance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1229-1232
• /
• 2008

We have successfully manufactured high-quality top-contact organic thin-film transistors using inkjet technologies with sub-femtoliter droplet volume. Silver fine lines were directly patterned by inkjet on pentacene channel layers. The minimum width of silver lines was $1{\mu}m$ with without the need for pre-patterning or surface pretreatments. The mobility was $0.3\;cm^2/Vs$.