• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.244-249
• /
• 1997

Internal and external heat sources will cause to deform to machine elements in the contact joint of structure,which results in the change of contact pressure distribution different from initial assembly. Heat induced variations of contact pressure will change the static and dynamic properties such as contact stiffness,damping as well as contact heat conduction in the structure. In order to design and control the intelligent machine tool operating in variant conditions more sophisticatedly, the good prediction for the changes of prescribed propeties are strongly required especially in the contact elements adjacent to the rotational or linear bearing This paper presents some computational and experimental results in regard to static and dynamic characteristics of the press-fitted bush and shaft assembly which is a model of the bearing innerrace and shaft assembly. In the condition of heat generation on the outer surface of the bush,the effects of changes in the negative clearance and the heat flux on pressure distribution and dynamic properties are investigated. Results of this study show that the edge effect of the bush and the initial clearance have effects on the transient dynamic characteristics significantiy.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.15-20
• /
• 2018

No-insulation (NI) pancake magnets are fabricated using Rare earth-Barium-Copper Oxide (REBCO) coated conductor (CC) tapes, which enabled a very compact magnet in the aspects of high critical current density ($J_c$) and high mechanical strength by removing insulation and allowing thinner stabilizer. They have also advantages such as self-quench protection. Therefore, it does not need quench detection and protection that can be very challenging in a high critical temperature ($T_c$) superconducting magnet technology. Recently, it was reported that the NI REBCO CC magnets have some drawbacks of long charging time and high field ramp loss which will be a concern in the operation of cryocooled magnets. These issues are related to the turn-to-turn contact resistivity and can be released by managing it. This is also closely related to the activity of reducing the contact joint resistance in the case of CC joints for long length CC fabrication. Therefore, in this study, the turn-to-turn contact resistance ($R_c$) at the CC contact part of differently stabilized CC tapes was measured. The behaviors of $R_c$ at CC contact parts according to the applied contact pressure were investigated. The range of $R_c$ measured for CC tapes adopted will provide fundamental data for design and fabrication of the CC NI coils.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.13-16
• /
• 2002

In this research, the design methods of the rocket joint parts were suggested. In the first section, nonlinear finite element analyses for joint parts of a composite pressure tank were performed. In the analyses, the detailed finite element modeling was performed and complex boundary conditions(contact problem, clamping force) were considered. Secondly, several guidelines for the design of joint parts were suggested. The parametric study for geometric design variables was peformed. Finally, the parametric study result was categorized for the multi-Joint part design of the axi-symmetric composite structure.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1157-1160
• /
• 1996

Control of a biped robot which has compliant ankle joints is dealt in this paper. Simulated version of a human ankle joint is built using springs and mechanical constraints, which gives a flexibility of joint and compliance against the touching ground. The biped robot with compliant ankle joints proposed here gives a good contact between its sole and the ground and makes foot landing soft. As a result, installing force sensors for measuring the center of gravity of the biped becomes easier. A motor to drive an ankle joint is not needed which makes legs light. However, the control problem becomes more difficult because the torque of the ankle joint to put the biped in a desired walking gait cannot be provided from the compliant ankle joint. To solve this problem, we proposed a dynamic gait modification method by adjusting the position of a hip joint. Simulation results for the mathematical model of the SD-2 biped in the Ohio State University are given to show the validity of the proposed controller.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1310-1315
• /
• 2003

Severe osteoarthrosis of the knee joint often requires total knee arthroplasty (TKA) to yield adequate knee function. The knee joint with TKA is expected ideally to restore the characteristics, however, this is not necessarily true in the clinical cases. In this study the motions of the intact joint and the joint after TKA were investigated numerically using computer simulation. For active knee extension from 90 degrees of flexion to full extension, the intact knee joint exhibited anterior tibial translation near the full extension while it showed only rotation for other flexion angles. Physiologic external rotation of the tibia near full extension was also noted in the analytical model. The analysis of the tibial insert of three different shapes (flat, semicurved, and curved types) demonstrated characteristic rotational and sliding motions as well as different contact forces.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.59-62
• /
• 2003

We fabricated two HTS closed coils by using resistive-joint method and the joint resistance of the coil was estimated by field decay technique at 77 K. In addition, we used the Runge-kutta method for the numerical analysis to estimate the decay properties. The joint resistances were evaluated as a function of critical current of HTS closed coil and external field strength of excitation coil. It was observed that joint resistance was independent of critical current and external field strength. It was estimated that joint resistance was 8.0$\times$10$^{-9}$ $\Omega$ to 11.9$\times$10$^{-9}$ $\Omega$ for coils of contact length for 7 cm.

• 한국정밀공학회지
• /
• 제21권9호
• /
• pp.188-195
• /
• 2004

Severe osteoarthrosis of the knee joint often requires total knee arthroplasty(TKA) to yield adequate knee function. The knee joint with TKA is expected ideally to restore the characteristics, however, this is not necessarily 1.ue in the clinical cases. In this study the motion of the intact joint and the joint after. TKA were investigated numerically using computer simulation. For active knee extension from 90 degrees of flexion to full extension, the intact knee joint exhibited anterior tibial translation near the full extension and it showed only rotation at other flexion angles. Physiologic external rotation of the tibia near full extension known as screw home movement was also noted in the analytical model. The analysis of the tibial insert of three different shapes (flat, semicurved, and curved types) demonstrated characteristic rotational and sliding motion as well as different contact forces.

• 한국전산구조공학회논문집
• /
• 제36권3호
• /
• pp.165-171
• /
• 2023

건설기계와 특장차의 상부와 하부 구조를 연결하는 로터리 조인트는 축과 하우징이 회전하면서 유압을 전달하는데 오일의 유로에 누유를 방지하기 위해 여러 개의 시일이 조립된다. 시일재료는 강성이 커서 조립에 어려움이 있기 때문에 자른 후 조립하는 방법을 모색하였다. 절단면의 모양은 L형과 /형으로 하였고 유압이 작용할 때 누유 기준은 절단면에 발생하는 접촉압력으로 하였다. 시일의 구조와 재료는 이중 탄성중합체로 구성되며 강성이 큰 PE 재질만 절단한 경우에 대하여 비선형 접촉 구조해석을 수행하였다. 연구결과 절단 길이가 짧을수록 누유 방지에 유리하며 PE와 하우징이 접촉하는 윗면보다 NBR과 PE가 접촉하는 아랫면으로 누유될 가능성이 큰 것으로 나타났다.

• 화약ㆍ발파
• /
• 제37권2호
• /
• pp.14-21
• /
• 2019

개별요소법은 절리가 발달한 불연속 암반의 모델링에 매우 유력한 수치해석적 방법이다. 또한 발파 후 큰 변위가 일어나는 단계에서의 모델링에도 효과적이다. 개별요소법에서 각 요소는 강체로 가정하고, 요소 간 약간의 중첩을 허용하여 접촉 변위로부터 상호 작용력을 계산한다. 개별요소의 경계로 정의되는 절리의 강성은 블록요소 상호 간의 거동을 결정하는 중요한 변수로서 변형의 크기와 파괴 양상에 영향을 준다. 그러나 요소 간 과도한 중첩으로 인한 수치해석적 불안정성을 방지하기 위해서 어떤 준정적인 문제에 있어서는 실제 절리 물성과 관계없이 임의로 선정된 절리 강성 값이 사용되기도 한다. 해석의 주된 관심사가 정밀도 높은 변형의 크기 예측이냐, 불연속체의 파괴 양상이나 파괴 후 파괴된 블록들의 거동 예측이냐에 따라, 절리 강성에 대한 입력 자료 값은 결과에 큰 영향을 주지 않을 수도 있고, 심각한 예측 오류를 가져올 수도 있다. 본 연구는 개별요소법을 이용한 수치해석 모델링에서 절리 강성 값이 해석 결과에 미치는 영향을 이해하고 입력자료 선정 지침에 도움을 주고자 수행되었다.

• 대한기계학회논문집A
• /
• 제29권1호
• /
• pp.1-13
• /
• 2005

Kinematics of grasping and manipulation by a multi-fingered robotic hand where multi-fingertip surfaces are in contact with an object is solved. The surface of the object was represented by B-spline surfaces in order to model the objects of various shapes. The fingers were modeled by cylindrical links and a half ellipsoid fingertip. Geometric equations of contact locations have been solved for all possible contact combinations between the fingertip surface and the object. The simulation system calculated joint displacements and contact locations for a given trajectory of the object. Since there are no closed form solutions for contact or intersection between these surfaces, kinematics of grasping was solved by recursive numerical calculation. The initial estimate of the contact point was obtained by approximating the B-spline surface to a polyhedron. As for the simulation of manipulation, exact contact locations were updated by solving the contact equations according to the given contact states such as pure rolling, twist-rolling or slide-twist-rolling. Several simulation examples of grasping and manipulation are presented.