• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.16-19
• /
• 2015

A wearable sensing ECG T-shirt for ubiquitous vital signs sensing is proposed. The sensor system consists of a signal processing board and capacitive sensing electrodes which together enable measurement of an electrocardiogram (ECG) on the human chest with minimal discomfort. The capacitive sensing method was employed to prevent direct ECG measurement on the skin and also to provide maximum convenience to the user. Also, low power integrated circuits (ICs) and passive electrodes were employed in this research to reduce the power consumption of the entire system. Small flexible electrodes were placed into cotton pockets and affixed to the interior of a worn tight NIKE Pro combat T-shirt. Appropriate signal conditioning and processing were implemented to remove motion artifacts. The entire system was portable and consumed low power compared to conventional ECG devices. The ECG signal obtained from a 24 yr. old male was comparable to that of an ECG simulator.

• 한국지열·수열에너지학회논문집
• /
• 제16권3호
• /
• pp.8-16
• /
• 2020

This paper presents the heating performance analysis results of a ground-source heat pump (GSHP) system using hybrid ground heat exchanger (HGHE). In this paper, the HGHE refers to the ground heat exchanger (GHE) using both a surface water heat exchanger (SWHE) and a vertical GHE. In order to evaluate the system performance, we installed monitoring sensors for measuring temperatures and power consumption, and then measured operation data with 4 different load burdened ratios of the HGHE. During the entire measurement period, the average heating capacity of the heat pump was 37.3 kW. In addition, the compressor of the heat pump consumed 9.4 kW of power, while the circulating pump of the HGHE used 6.7 kW of power. Therefore, the average heating coefficient of performance (COP) for the heat pump unit was 4.0, while the system including the circulating pump was 2.7. Finally, the parallel use of SWHE and VGHE was beneficial to the system performance; however, further researches are needed to optimize the design data for various load ratios of the HGHE.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1139-1147
• /
• 2015

In this paper, an algorithm based on a model analysis of the online calculation of the root-mean-square (RMS) value of welding current for single-phase AC resistance spot welding (RSW) was developed. The current is highly nonlinear and typically non-sinusoidal, which makes the measuring and controlling actions difficult. Though some previous methods focused on this issue, they were so complex that they could not be effectively used in general cases. The electrical model of a single-phase AC RSW was analyzed, and then an algorithm for online calculation of the RMS value of the welding current was presented. The description includes two parts, a model-dependent part and a model-independent part. Using a previous work about online measurement of the power factor angle, the first part can be solved. For the second part, although the solution of the governing equation can be directly obtained, a lot of CPU time must be consumed due to the fact that it involves a lot of complex calculations. Therefore, a neural network was employed to simplify the calculations. Finally, experimental results and a corresponding analysis showed that the proposed algorithm can obtain the RMS values with a high precision while consuming less time when compared to directly solving the equations.

• 전기학회논문지P
• /
• 제67권4호
• /
• pp.214-220
• /
• 2018

Light sources induced by gas discharge using rare gases have been widely used in the thin film deposition, the surface modification and the polymer etching. A dielectric barrier discharge (DBD) has been developed in order to consistently emit light and control the wavelength of the emission light. However, much research on the characteristics of the movement of discharge particles is required to improve the efficiency of the light lamp and the life-time of the light apparatus in detail. In this paper, we developed a He DBD discharge simulation tool and investigated the characteristics of discharge particles which were electrons, two positive ions ($He^+$, $He_2^+$) and 5 excited particles ($He^*(1S)$, $He^*(3S)$, $He^*$, $He^{**}$, $He^{***}$). The discharge currents showed the transition from pulse mode to continuous mode with the increase of power. With the accumulated charges on the barrier walls, the discharge current was rapidly increased and caused oscillation of the discharge voltage. As the gas pressure increased, $He_2^+$ and $He^*(3S)$ became the dominant activated particles. The input power was mostly consumed by electrons and $He_2^+$ ion. And the change curve showed that power consumption by electrons increased more with gas pressure than with source voltage or frequency.

• Journal of Information Processing Systems
• /
• 제17권1호
• /
• pp.63-74
• /
• 2021

According to the double-phase cluster-head election method (DCE), the final cluster heads (CHs) sometimes are located at the edge of cluster. They have a long distance from the base station (BS). Sensor data is directly transmitted to BS by CHs. This makes some nodes consume much energy for transmitting data and die earlier. To address this problem, energy efficient multi-hop cluster-head election strategy (EEMCE) is proposed in this paper. To avoid taking these nodes far from BS as CH, this strategy first introduces the distance from the sensor nodes to the BS into the tentative CH election. Subsequently, in the same cluster, the energy of tentative CH is compared with those of other nodes, and then the node that has more energy than the tentative CH and being nearest the tentative CH are taken as the final CH. Lastly, if the CH is located at the periphery of the network, the multi-hop method will be employed to reduce the energy that is consumed by CHs. The simulation results suggest that the proposed method exhibits higher energy efficiency, longer stability period and better scalability than other protocols.

• 한국지능시스템학회논문지
• /
• 제24권4호
• /
• pp.403-411
• /
• 2014

본 논문에서는 가전기기의 전력소비 정보를 이용하여 가전기기별 특성을 추출하고 이를 이용하여 데이터베이스의 자동 구축 및 구축된 데이터베이스로부터 입력되는 특성 정보에 해당하는 가전기기를 식별할 수 있는 알고리즘을 설계하고 구현하였다. 이를 위해 가정환경에서 사용하는 가전기기들의 소비전력 상태 감시 및 전원 제어가 가능한 기존에 설계된 시스템서버에 별도의 라이브러리를 구현하여 추가하였다. 구현된 최종 시스템은 가전기기의 소비전력을 측정하고 무선 네트워크를 이용하여 서버에게 실시간으로 데이터를 전송하는 클라이언트와 서버로 구성이 되며, 실험을 통해 특정 클라이언트에 연결된 특정 가전기기를 자동으로 식별하는 것이 가능한 것을 검증하였다.

• 설비공학논문집
• /
• 제17권4호
• /
• pp.285-296
• /
• 2005

In order to reduce the compression power and to use the overall energy contained in LNG effectively, a combined cycle is devised and simulated. The combined cycle is composed of two cycles; one is an open cycle of liquid/solid carbon dioxide production cycle utilizing LNG cold energy in $CO_2$ condenser and the other is a closed cycle gas turbine which supplies power to the $CO_2$ cycle, utilizes LNG cold energy for lowering the compressor inlet temperature, and uses the heating value of LNG at the burner. The power consumed for the $CO_2$ cycle is investigated in terms of a production ratio of solid $CO_2$. The present study shows that much reduction in both $CO_2$ compression power (only $35\%$ of power used in conventional dry ice production cycle) and $CO_2$ condenser pressure could be achieved by utilizing LNG cold energy and that high cycle efficiency ($55.3\%$ at maximum power condition) in the gas turbine could be accomplished with the adoption of compressor inlet cooling and regenerator. Exergy analysis shows that irreversibility in the combined cycle increases linearly as a production ratio of solid $CO_2$ increases and most of the irreversibility occurs in the condenser and the heat exchanger for compressor inlet cooling. Hence, incoming LNG cold energy to the above components should be used more effectively.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1591-1602
• /
• 1996

In operating the underwater engines such as encountered in exploring submarines, the dumping of the exhaust gas out of the engine requires a large portion of the total power, frequently amounting to 25-30% of the power generated. This unfavorable circumstance can be cured by liquefying the exhaust gas and storing it. In the present study, two liquefaction systems were simulated to enhance the overall efficiency; one is a closed cycle diesel engine and the other is a closed cycle LNG engine. The liquefied natural gas (LNG) is chosen as a fuel, not only because its use is economical but also because its cold energy can be utilized within the liquefaction system. Since a mixture of oxygen and carbon dioxide is used as an oxidizer, liquefying carbon dioxide is of major concern in this study. For further improving this system, the intercooling of the compressor is devised. The necessary power consumed for the liquefying system is examined in terms of the related properties such as pressure and temperature of the carbon dioxide vessel as a function of the amount of the exhaust gas which enters the compressor. The present study was successful to show that much gain in the power and reduction of the vessel pressure could be achieved in the case of the closed cycle LNG engine. The compression power of exhaust gas were observed remarkably lower, typically only 6.3% for the closed cycle diesel engine and 3.4% for the closed cycle LNG engine respectively, out of net engine power. For practicality, a design -purpose map of the operating parameters of the liquefaction systems was also presented.

• 한국정보통신학회논문지
• /
• 제20권10호
• /
• pp.1873-1880
• /
• 2016

셀룰러 네트워크를 운용하는데 드는 에너지의 대부분은 기지국에 의해서 소비되므로 에너지 효율적인 셀룰러 네트워크를 위하여 기지국의 송신 전력을 줄이는 것이 필요하다. 본 논문에서는 셀룰러 네트워크의 에너지 효율을 향상시키기 위한 목적으로 플로킹(flocking) 모델에 기반한 분산 송신전력제어 알고리즘을 제안한다. 새 무리에서 각각의 새가 자신의 속도를 인접한 이웃 새들의 평균 속도로 맞춰 날아가는 것과 같이, 제안 방안에서는 각 셀의 단말의전송률이 인접 셀의 같은 채널을 사용하는 단말의 평균 전송률과 같도록 서빙 기지국의 송신 전력을 제어한다. 모의실험 결과 제안한 분산 송신전력제어 알고리즘은 플로킹 모델과 같은 수렴 속성을 가지며, 셀 간 간섭이 증가함에 따라 낮은 아웃티지 확률을 유지하면서도 기지국의 전력 소모를 효과적으로 줄일 수 있음을 보여준다. 이를 통하여 제안 방안은 기지국 수가 20개 이상일 때 셀룰러 네트워크의 에너지 효율을 기존 방식 대비 두 배 이상 향상시킨다.

• 전기학회논문지
• /
• 제66권12호
• /
• pp.1682-1688
• /
• 2017

In modern society, the number of industrial customers using equipment sensitive particularly to voltage sags is rapidly increasing. As voltage sags can cause loss of information as well as false operation of the control device, it results in the vast economic damage in industrial processes. One way to mitigate voltage sags in the sensitive loads is the installation of distributed generation (DGs) on the periphery of these loads. In addition, renewable energy sources are currently in the spot light as the potential solution for the energy crisis and environmental issues. In particular, wind power generation which is connected to a grid is rising rapidly because it is energy efficient and also economically feasible compared to other renewable energy sources. On the basis of the above information, in this paper, with Wind Turbine Generators (WTGs) installed nearby the sensitive load, the analysis of the mitigating effect comparison by types of WTGs is performed using voltage sag assessment on the IEEE-30 bus test system. That is, the areas of vulnerability according to types of WTGs are expected to be different by how much reactive power is produced or consumed as WTG reactive power capability is related to the types of WTGs. Using the concept of 'Vulnerable area' with the failure rate for buses and lines, the annual number of voltage sags at the sensitive load with the installation of WTGs per type is studied. This research will be anticipated to be useful data when determining the interconnection of wind power generation in the power system with the consideration of voltage sags.