• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.29-44
• /
• 1999

This paper shows the results of model tests on the lateral behavior of single rigid pile, which was constructed by driving, in homogeneous and non-homogeneous (two layered) NakDong River sands. The purpose of the present paper is to investigate the effect of ratio of lower layer thickness to embedded pile length, relative density of sand and pile construction conditions (Driven & Embedded piles) on the characteristics of lateral behavior of single pile. These effects can be quantified only by the results of model tests. As a model result, the lateral behavior depends upon the pile construction condition in loose-density soil more than in high-density soil. If the pile construction depends upon driving construction, the decrease of deflection remarkably increases for both loose homogeneous sand and non-homogeneous soil$(E_{h1}/E_{h2}/=0.18)$ with high thickness of upper layer but the decrease of maximum bending moment shows the opposite result to the decrease of deflection. And, with respect to deflection, it was found that the deflection ratio $(y_{Driven}y_{Embedded})$ of embedded to driven piles has the ranges of 0.65 - 0.88 $(D_r=90%)$0.38 - 0.65 $(D_r=61.8%)$ for each relative density of homogeneous soil and the range of 0.6 - 0.88 for non-homogeneous soil. Also, in this study, the experimental equation for the effects of drop height (DH) and H/L on the ratios of $y_D/y_E\; and MBM_D/MBM_ E$ is suggested from model tests.

• Corrosion Science and Technology
• /
• v.6 no.5
• /
• pp.219-226
• /
• 2007

Pre-construction primer (PCP), or shopprimer, have been applied to steel plates to control temporary corrosion during ship fabrication. For surface preparation at ship block stage, in common shipyard practices, welding beads, burnt and rusted areas shall be blasted or power tool cleaned and the contamination such as zinc salt shall be removed with blasting or power tool. Whereas, the sound film of PCP needs not to be removed or roughened as the paint having good compatibility with PCP is used for the first coat. In many cases, however, full blasting or sweep blasting on the sound PCP treated block assemblies was requested. There still has been argument about the legitimacy of this practice, thus, it is critical to evaluate the quality of the coating system applied on the sound PCP retained condition, comparing with the one applied on the full blasted or sweep blasted condition. In this study, two different epoxy systems for water ballast tank were applied on the surfaces with sound PCP condition, full blasted condition, and sweep blasted condition. Coating performances such as durability, anti-corrosion, cathodic disbondment resistance were evaluated. The test results clearly indicated that the sound film of PCP needed not to be removed or roughened as the paint having good compatibility with PCP based on inorganic zinc silicate.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.4 no.3
• /
• pp.22-29
• /
• 2013

In recent years, the construction of high-rise buildings are promoted. According to these, there are many needs about new technologies to strengthen the building performance and high-strength steel is regarded as one of these for promoting building performance. In Korea, high-strength steels which stress are over 600MPa are on market and in aborad, super high-strength steels over 1000MPa are developing and they expected to promote the building performance. But there are still doubts about applying high-strength steel members because of size effect and worry of brittle fracture. In this reports, we propose results of performance and analysis tests for use with general steel. We propose the characteristic of high-strength steels first and next the results of performance test to show they satisfy the performance that designers expect. And last, we compare the results of test and analysis for acquire the alanysis reliability in non-linear analysis with high-strength steels.

• Tunnel and Underground Space
• /
• v.23 no.1
• /
• pp.42-53
• /
• 2013

The percussion rate and spacing of the button of drill bit are very important in maximizing the drilling efficiency. Therefore, a series of percussion tests using Hopkinson bar system was carried out to assess the fragmentation performance against the beat rate and spacing of a drill bit. First, single percussion test complemented with numerical simulation was performed to analyze rock fragmentation phenomenon and to describe the fragmentation process. Next, multiple percussion test that repetitively strike the rock sample moving at predetermined rate was carried out to predict drilling efficiency against the button spacing. After the tests, the fragmented volume of the rock was measured by laser scanner and the drilling performance was analyzed using the calculated percussive energy and measured negative volume. Based on the results, the single impact performance of drill bit with 102 mm diameter was predicted.

• Journal of the Korean Society for Library and Information Science
• /
• v.37 no.4
• /
• pp.223-240
• /
• 2003

The process of managing the results of national R&D projects, which are aimed at strengthening national competitiveness has been ineffective so far. The existing structure for managing the results of national R&D projects have largely been relying on just strong and managing the result of each project and not on the utilization and expansion of the results for further application. We aim at developing a system that would exceed the current system which heavily relies on a passive paradigm of management and circulation of technology. Through the newly developed system, we look forward to achieve the major goals of R&D, such as cutting down the expenses, increasing the margin improving the technology and expanding the influence of the research to other areas from through improving the system as well as the process for managing R&D projects.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.855-858
• /
• 1995

A neural network has very simple construction (input, output and connection weight) and then it can be robusted against some disturbance. In this paper, we proposed a neuro-controller using a Multi-Layered neural network which is combined with PD controller. The proposed neuro-controller is learned by backpropagation learning rule with momentum and neuro-controller adjusts connection weight in neural network to make approximate dynamic model of DC Servo motor. Computer Simulation results show that the proposed neuro-controller's performance is better than that of origianl PD controller.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.453-467
• /
• 2018

The excavation performance and the cutting tool wear prediction of shield TBM are very important issues for design and construction in TBM tunneling. For hard-rock TBMs, CSM and NTNU model have been widely used for prediction of disc cutter wear and penetration rate. But in case of soft-ground TBMs, the wear evaluation and the excavation performance have not been studied in details due to the complexity of the ground behavior and therefore few testing methods have been proposed. In this study, a new soil abrasion and penetration tester (SAPT) that simulates EPB TBM excavation process is introduced which overcomes the drawbacks of the previously developed soil abrasivity testers. Parametric tests for penetration rate, foam mixing ratio, foam concentration were conducted to evaluate influential parameters affecting TBM excavation and also ripper wear was measured in laboratory. The results of artificial soil specimen composed of 70% illite and 30% silica sand showed TBM additives such as foam play a key role in terms of excavation and tool wear.

• Journal of the Korean Society for Library and Information Science
• /
• v.38 no.1
• /
• pp.281-301
• /
• 2004

The national investment versus research result management ratio is very low as we compare to those of other advanced countries. Also the system of efficient usage of research result is insufficient. It results inefficient R＆D investment when we drive national R＆D programs. In this paper we developed a generalized information system for efficient planning and management of national R＆D programs. And we developed a efficient system of the R＆D information support and a system of a smoothly circulating R＆D information. Also we apply those systems to the development of the information system of Korea Research Council of Fundamental science and technology. This application system can provide a total R＆D information of whole life cycle of the national R＆D programs.

• Journal of the Korean Institute of Gas
• /
• v.5 no.2 s.14
• /
• pp.30-35
• /
• 2001

Presently, working gas pipelines are being subjected to the influence of construction vibration. Especially on subway and road construction, gas pipelines are being influenced to construction vibration caused by use of construction equipment, passage of a large-sized vehicle and blasting. Buried gas pipelines are subjected to the influence of vibration caused by blast in the vicinity of pipeline, exposed gas pipelines are subjected to the influence of vehicle vibration. Therefore, in the study, it is developed to vibration prediction program of gas pipeline by analyzing measured construction vibration. This program is able to predict vibration of gas pipeline according to field conditions by using the results of structural finite element analysis and empirical equation by reliability analysis. And, this program contains the database of construction vibration. Additionally, this program is able to compute estimated blast vibration equation using measured blast vibration data in the field and to form graph of allowable charging gunpowder per delayed-action with the change of blast velocity. Therefore, field workers are able to predict construction vibration around gas pipeline and estimate safety of gas pipeline.

• Korean Journal of Construction Engineering and Management
• /
• v.23 no.2
• /
• pp.24-32
• /
• 2022

In Korea, the productivity of the construction industry is evaluated at a very low level, and the utilization of the elemental technology of the Fourth Industrial Revolution is also very low compared to other industries. In order to solve this problematic situation, it is necessary to identify the demand for technology improvement in the specialty construction industry that is directly in charge of construction in projects. Therefore, this study aims to investigate improving construction competitiveness and the demand for technology improvement in Korea's specialty construction industry. First, the concept and status of classification of the specialized construction industry were identified, and a questionnaire was organized. Second, a survey was conducted on experts construction experts, and the demand for technical improvement of the specialty construction industry was derived by applying AHP and cluster analysis. The results of this study will serve as a practical reference for policy development, R&D direction, and technology development roadmap to enhance construction competitiveness in the future, and ultimately will help to present directions to improve the construction competitiveness of the construction industry.