• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.620-629
• /
• 2022

By varying various experimental conditions such as heating rate, molar hourly space velocity (MHSV), and nitridation reaction temperature, vanadium oxynitride was prepared through temperature programmed reduction/nitridation reaction (TPRN) of vanadium pentoxide and ammonia, and characterization were performed. In order to investigate the physico-chemical properties of the prepared catalyst, N₂ adsorption-desorption analysis, X-ray diffraction analysis (XRD), hydrogen temperature programmed reduction (H₂-TPR), temperature programmed oxidation (TPO), ammonia temperature programmed desorption (NH₃-TPD), transmission electron microscopy (TEM) was performed. Transformation of V₂O₅ with 5 m² g^-1 low specific surface area by reduction at 340 ℃ to V₂O₃ showed a high specific surface area value of 115 m² g^-1 by micropore formation. As the nitridation temperature increased beyond that, the specific surface area continued to decrease due to sintering. The nitridation reaction variable that had the greatest influence on the specific surface area was the reaction temperature, and the x + y value of VN_xO_y of a single phase approached from 1.5 to 1.0 as the nitridation reaction temperature increased. At a high reaction temperature of 680 ℃, the cubic lattice constant a was VN. close to the value. At 680 ℃, the highest nitridation temperature among the experimental conditions, the ammonia conversion rate was 93%, and no deactivation was observed.

• Korean Journal of Food Science and Technology
• /
• v.27 no.5
• /
• pp.646-651
• /
• 1995

The correlation between the bitter taste and the surface tension was found for bitter tasting, aqueous solutions. By the Szyszkowski's equation, the surface tension (STR) and taste curves (JND) were derived more clearly using the Techplot program. The specific capillary activity (log b values) for bitter tasting solutions are negatively correlated to the recognition threshold. It was shown that a more bitter substances has greater capillary activity. The correlation between the recognition threshold $(log\;C_{1})$ and the substance specific constant (a and b values) of sensory (JND) and surface tension values indicates good agreement. This means that the model of surface area adsorption in the solution/air system can apply also for the sensory model microvillus membrane in the mouth.

• Restorative Dentistry and Endodontics
• /
• v.29 no.5
• /
• pp.454-461
• /
• 2004

The purpose of this study is to compare and to evaluate the effects of the degree of saturation on the progression of artificial root caries lesion. A total of 8 human premolars without any defects and cracks selected and the cementum were removed and the teeth were cleaned with ultrasonic device and pumice without fluoride. Each tooth was sectioned into 6 pieces and they were ground with #800 sandpaper until they had a thickness of 200pm. Specimens were applied with nail vanish except for the 2-3 mm window area after application of bonding agent. Under the constant pH, the specimens were divided into 6 groups (degree of saturation: 0.1415, 0.1503, 0.1597, 0.1676, 0.1771. 0.1977). Each group was immersed in acid buffer solution for 1. 2, 3, 5 days under controlled temperature ($25^{\circ}C$) and imbibed in water and examined using the polarizing microscope. The results were as follows 1. Although the degree of saturation of demineralization solution decreased, the depth of penetration in the dentin was constant. 2. Erosion was observed on the surface of all the teeth in the group I, II. In the group III, IV, V, surfaces were not changed. The teeth in the group VI showed the more mineralized surface but not the shape of the dentinal tubules distinctively. 3. In all groups, the lesion progressed rapidly at the first day of the experiment, but increased gradually as time elapsed.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.455-461
• /
• 2013

Mar behavior and visibility were investigated by applying a constant load to various gloss-coated urethane-acrylate surfaces. Using a area-contact scratch tip which can apply a relatively low stress level to the coated surfaces, the mar damages were generated on the surfaces. When evaluating the mar-induced damage by means of delta-gloss (${\Delta}G$) and delta-luminance (${\Delta}L$) with existing test methodologies, an increase in constant load on the same gloss-coated surface leads to an increase in ${\Delta}G$ and ${\Delta}L$. However, these are not suitable for evaluating and comparing the surface damages of different gloss-coated samples because of a disagreement between the measured values and the mar visibility. It is shown that new mar test assessment proposed in this work not only can be used to quantitatively evaluate the mar damage, but also accounts for the correlation that the increases of the normalized gloss and luminance on coated surfaces correspond with an increase in the mar visibility.

• Nano
• /
• v.13 no.11
• /
• pp.1850127.1-1850127.13
• /
• 2018

Bi metal deposited on $Bi_2MoO_6$ composite photocatalysts have been successfully synthesized via a simple reduction method at room temperature with using $NaBH_4$ as the reducing agent. The photocatalytic activity of the composite was evaluated by degradation of rhodamine B (RhB) and bisphenol A (BPA) solution under visible light. The rate constant of $Bi/Bi_2MoO_6$ composite to RhB is 10.8 times that of $Bi_2MoO_6$, and the degradation rate constant of BPA is 6.9 times of that of $Bi_2MoO_6$. Nitrogen absorption-desorption isotherm proved that the increase of specific surface area is one of the reasons for the improvement of photocatalytic degradation activity of $Bi/Bi_2MoO_6$ composites. The higher charge transfer efficiency of $Bi/Bi_2MoO_6$ is found through the characterization of the photocurrent and impedance, which are attributed to the surface plasmon resonance (SPR) effect produced by the introduction of the metal Bi monomer in the composite. Free radical capture experiments proved that cavitation is the main active species. Based on the above conclusions, a possible mechanism of photocatalytic degradation is proposed.

• Korean Journal of Remote Sensing
• /
• v.34 no.2_2
• /
• pp.313-326
• /
• 2018

This paper introduces core techniques on ship detection and tracking based on a compact HF radar platform which is necessary to establish a wide-area surveillance network. Currently, most HF radar sites are primarily optimized for observing sea surface radial velocities and bearings. Therefore, many ship detection systems are vulnerable to error sources such as environmental noise and clutter when they are applied to these practical surface current observation purpose systems. In addition, due to Korea's geographical features, only compact HF radars which generates non-uniform antenna response and has no information on target information are applicable. The ship detection and tracking techniques discussed in this paper considers these practical conditions and were evaluated by real data collected from the Yellow Sea, Korea. The proposed method is composed of two parts. In the first part, ship detection, a constant false alarm rate based detector was applied and was enhanced by a PCA subspace decomposition method which reduces noise. To merge multiple detections originated from a single target due to the Doppler effect during long CPIs, a clustering method was applied. Finally, data association framework eliminates false detections by considering ship maneuvering over time. According to evaluation results, it is claimed that the proposed method produces satisfactory results within certain ranges.

• Journal of the Korean Chemical Society
• /
• v.20 no.5
• /
• pp.351-357
• /
• 1976

Adsorption isotherms of benzene and p-xylene on both of Spheron 6 (a graphitized carbon black) and Alucer (Alumina) are obtained at various temperatures using a sensitive quartz beam microbalance. From these isotherms BET plots are made to obtain the molecular areas of these adsorbates. On the Spheron 6, the molecular area of p-xylene remains constant until the temperature is increased up to $19^{circ}C$, increases abruptly at $19^{circ}C$ through $19.2^{circ}C$, and then again remains constant thereafter. On the other hand, adsorbed benzene molecules give a quite temperature-independent molecular area. The results are interpreted as the adsorbed p-xylene molecules and benzene molecules are localized on the adsorbents with compact packing, while it gains a hindered-rotational degree of freedom at the expense of vibrational one at the higher temperatures. This peculiar behavior of adsorption is considered as due to the interactions between benzene rings of adsorbents and graphite surface. Molecular areas of these adsorbates on Alucer M. A. increase gradually with temperature, indicating that the adsorbed molecules are unlocalized.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.5
• /
• pp.423-430
• /
• 2016

In this study, we investigated the corrosion damage characteristics of steel for offshore wind turbine tower substructure using an accelerated electrochemical test. The galvanostatic corrosion test method was employed with a conventional 3 electrode cell in natural sea water, and the steel specimen was served as a working electrode to induce corrosion in an accelerated manner. Surface and cross-sectional image of the damaged area were obtained by optical microscope and scanning electron microscope. The weight of the specimens was measured to determine the gravimetric change before and after corrosion test. The result revealed that the steel tended to suffer uniform corrosion rather than localized corrosion due to active dissolution reaction under the constant current regime. With increasing galvanostatic current density, the damage depth and surface roughness of surface was increased, showing approximately 25 times difference in damage depth between the lowest current density ($1mA/cm^2$) and the highest current density ($200mA/cm^2$). The gravimetric observation showed that the weight loss was proportionally increased with increment of current density that has 75 times different according by experimental conditions. Consequently, uniform corrosion of the steel specimen was conveniently induced by the electrochemically accelerated corrosion technique, and it was possible to control the extent of the corrosion damage by varying the current density.

• Journal of Environmental Science International
• /
• v.10 no.5
• /
• pp.315-321
• /
• 2001

This study was conducted to estimate the decomposition capacity for organic matter by microbe of tidal flat sediments (Hajae, Dongjin and Mankyung). The decomposition rate constants (K') have been determined by Thomas slope method and compared with the values of each tidal flats. The decomposition rates of organic matter by microbe were initially very slow, but at the end of 12 hours, very sharply increased. The values of decomposition rate constant for Dongjin, Mankyung and Hajae tidal flat sediment were 1.364$day^{-1}$/, 1.080d$day^{-1}$ and 0.735$day^{-1}$, respectively. The decomposition rate constant of Dongjin tidal flat sediment which affected by livestock wastewater was higher than others. The decomposition quantity (mg/g/day) of organic matter by microbe of tidal flat sediments was 0.4mg/g/day for Dongjin, 0.36mg/g/day for Mankyung and 0.36mg/g/day for Hajae. The average of decomposition quantity was 0.37mg/g/day. To calculate purification capacity (kg/ha) of organic matter by microbe, we applied to two assumption ; 1) biological action by microbe is occur within 0.1cm under surface 2) specific gravity of sediment are 2.5g/$\textrm{cm}^2$. The purification capacity of organic matter by microbe of tidal flat sediment was calculated to 9.25kg/ha. The relationships between decomposition rate constant (K') and ignition loss (I. L), chemical oxygen demand by sediment (CO $D_{sed}$), total carbon(TC), silt and clay as index of organic matter were a high positive($R^2$=0.97~1.00).