• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.4
• /
• pp.73-80
• /
• 2013

In this paper, an experimental circuit model for an accurate high-frequency characterization of transmission line is proposed. Inherent resonance effects during measurements make it difficult to determine characteristic impedance and propagation constant at the resonance frequencies corresponding to the line length. Thus, resonance-effect-free transmission line parameter determination technique based on the physical insight and theory is proposed. Then, by using the parameters high-frequency circuit model is proposed for high-speed signal propagation characterization. The proposed frequency-variant transmission line model is verified with measurement and it can be usefully exploited in high-speed signal propagation characterization.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.2
• /
• pp.30-38
• /
• 2003

This paper proposed PID controller for torch slider and PD controller for motor right wheel. to control the motion of two-wheeled welding mobile robot with seam tracking sensor touched on welding line. The motion control is realized in the view of keeping constant welding velocity and precise seam tracking even though the target welding line is on straight line or curved line. The position and direction of the body of the mottle robot are controlled by using signal errors between seam tracking sensor and body positioning sensor attached on the end of torch slider and body side of the mobile robot, respectively. In turning motion, the body and the torch slider are controlled by using the kinematic model related with two motions of body turning and torch sliding. The straight locomotion is controlled according to eleven control patterns obtained from displacements between two sensors of the seam tracking sensor and the body positioning sensor. The effectiveness is proven through the experimental results fur lattice type welding line. Through the experimental results, we can see that the position value of the electrode end point and the welding velocity are controlled almost constantly both in straight and turning locomotion.

• Geomechanics and Engineering
• /
• v.15 no.2
• /
• pp.769-774
• /
• 2018

The growth of cities requires the construction of new tunnels close to the existing ones. Prediction and control of ground movement around the tunnel are important especially in urban area. The ground respond due to EPB (Earth Pressure Balance) pressure are investigated using the finite element method by ABAQUS in intersection of the triplet tunnels (Line 2, 3 and 4) of Mashhad Urban Railway in Iran. Special attention is paid to the effect of EPB pressure on the tunnel face displacement. The results of the analysis show that in EPB tunneling, surface settlement and face displacement is related to EPB pressure. Moreover, it is found that tunnel construction sequence is a great effect in face displacement value. For this study, this value in Line 4 where is excavated after line 3, is smaller than that line. In addition, the trend of the displacement curves are changed with the depth for all lines where is located in above and below, close to and above the centerline tunnel face for Line 2, 3 and 4, respectively. It is concluded that: (i) the surface settlement decreases with increasing EPB pressure on the tunnel face; (ii) at a constant EPB pressure, the tunnel face displacement values increase with depth. In addition, this is depended on the tunneling sequence; (iii) the trend of the displacement curves change with the depth.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.9
• /
• pp.671-678
• /
• 2003

Spacer dampers maintain the constant gaps between each conductor in a bundle conductor-transmission line, and are installed at proper intervals to keep a line from all sorts of damages derived from the vibration energy caused by mechanical or electrical external factors. It is most important to embody a technology which considers difficulties of maintenance and repair, and has optimum elements in order to prevent accidents such as destruction by fire or the snapping of a wire by the effect of vibration phenomenon coming from transmission line. In the present thesis, therefore, the analysis of vibratory characteristics of spacer damper is set up by analytical methods such as the analysis of conductor motion's governing equation, the equation of spacer damper's motion, spacer damper-fastened wire's motion in a span, and the numerical analysis of finite difference method. Furthermore, the installation distance between spacer dampers was scrutinized by simulations of various vibration phenomena which change at any time as actual conditions do, and hereafter we will be able to analyze all kinds of vibration phenomena coming from a boltless spacer damper with 6 bundle conductor for 765 k V transmission line based on new analytical methods.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.69-75
• /
• 2001

Photoimageable thick film technology is a new technology in that the lithography process such as exposure and development is applied to the conventional thick film process. Line resolution of 25 $\mu\textrm{m}$ width and 25 $\mu\textrm{m}$ space could be obtained by laminating green sheet, printing photoimageable Ag paste, exposing the test patterns, developing, and co-firing. In case of using the alumina substrate, 20 $\mu\textrm{m}$ fine line could be also obtained by similar process. Test results showed that exposing power density and developing time were the most important processing parameters for the fine line formation. Microstrip and series gap resonators with well-defined line morphology and good transmission characteristics in high frequency were formed by this new technology, and thereby dielectric constant and loss of test substrate were calculated.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.8
• /
• pp.1-6
• /
• 1999

The only transmission characteristics in frequency domain is considered when using the tapered transmission line for wide-band impedance matching in MCM and MIC designs. In this paper, the distortion of an electrical pulse with rise/fall time resulting from dispersion and reflection as it propagates along a tapered microstrip line is investigated, and the delay time and distortion rate with respect to input and load impedances are analyzed on triangular and exponential tapered lines. A dispersion model of the phase constant proposed by Kirschning-Jansen is used to meet the frequency, accuracy and microstrip parametric requirements. The triangular tapered line shows both shorter delay time and higher distortion rate than those of the exponential tapered line. Furthermore, the amplitude of signal reflected from load point is calculated in time domain.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.325-331
• /
• 2010

In this study, highly miniaturized short-wavelength meander line employing eriodically patterned ground structure (PPGS) was developed for application to miniaturized on-chip passive component on GaAs MMIC (monolithic microwave integrated circuit). The meander line employing PPGS showed shorter wavelength and slow-wave characteristic compared with conventional meander line. The wavelength of the meander line employing PPGS structure was 17 % of the conventional meander line on GaAs MMIC. Due to its slow-wave structure, the meander line employing PPGS exhibited large propagation constant than conventional meander line, which resulted in larger phase shift and shunt inductance value. Above results indicate that the meander line employing PPGS is a promising candidate for application to a development of miniaturized on-chip RF components as well as inductor with a high inductance value on GaAs MMIC.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.4
• /
• pp.381-388
• /
• 1997

This paper proposes a heuristic algorithm to efficiently perform line balancing in the PCB assembly line including multiple surface mounters efficiently. Generally, the problems in line balancing are classified into two kinds. Firstly, is the determining of the minimum number of machines required for achieving the desired production rate. Secondly, is the assign of jobs to multiple machines in order to minimize the cycle time which is defined as a maximum among the working times of machines when the number of machines is fixed. In this paper, we deal with the latter. We consider a PCB assembly line, including the multiple surface mounters arranged serially as a target system. Also, the conveyor is assumed to move at a constant speed and have no buffer. Considering that the minimum number of machines required for the desired production rate is a discrete nonincreasing function which is inversely proportional to the cycle time, we propose an optimization algorithm for line balancing by using the binary search method. The algorithm is validated through computer simulation, the results of which show that their shapes coincide nearly with those of optimal line balancing efficiency graphs regardless of the number of components, the performance of surface mounters, and the structure of assembly line.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.99-105
• /
• 2022

As the chip size gets smaller, the width of the electrode line is also fine, and the density of interconnections is increasing. As a result, RC delay is becoming a problem due to the difference in resistance between the capacitor layer and the electrical conductivity layer. To solve this problem, the development of electrodes with high electrical conductivity and dielectric materials with low dielectric constant is required. In this study, we developed low dielectric ink by mixing commercial PSR which protect PCB's circuits from external factors and PI with excellent thermal property and low-k characteristics. As a result, the ink mixture of PSR and PI 10:3 showed the best results, with a dielectric constant of about 2.6 and 2.37 at 20 GHz and 28 GHz, respectively, and dielectric dissipation was measured at about 0.022 and 0.016. In order to verify the applicability of future applications, various line-width transmission lines produced on Teflon were evaluated, and as a result, the loss of transmission lines using low dielectric ink mixed with PI was 0.12 dB less on average in S21 than when only PSR was used.

• Macromolecular Research
• /
• v.12 no.2
• /
• pp.246-250
• /
• 2004

We have classified a number of aqueous ternary systems containing two different polymers into three types by focusing on the deviation of the Huggins constant k'from the additivity line. Systems of type I have negative deviations of k'; the repulsive interaction between the two different polymers dominates. In systems of type II, k' almost follows the additivity relation; the repulsive and attractive interactions between the two different polymers are balancing. Type III systems have positive deviations of k'; the attractive interactions are relatively dominant. This classification of systems is supported by the fact that the positive and negative deviations of k' from the additivity line also correspond to the sign of interaction parameter between polymer 2 and 3, Δb$\_$23/. Furthermore, we have verified the relatively high compatibility between dextran and poly(vinyl alcohol) by determining the binodal concentration of a liquid-liquid phase separation for a water/dextran/poly(vinyl alcohol) system, which is classified as type III. Thus, we found that the compositional dependence of k' closely relates to the compatibility of binary polymer mixtures in aqueous ternary systems.