• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.471-478
• /
• 2011

This paper addresses the establishment of a kVA-range plug-in hybrid electrical vehicle (PHEV) integration test platform and associated issues. Advancements in battery and power electronic technology, hybrid vehicles are becoming increasingly dependent on the electrical energy provided by the batteries. Minimal or no support by the internal combustion engine may result in the vehicle being occasionally unable to recharge the batteries during highly dynamic driving that occurs in urban areas. The inability to sustain its own energy source creates a situation where the vehicle must connect to the electrical grid in order to recharge its batteries. The effects of a large penetration of electric vehicles connected into the grid are still relatively unknown. This paper presents a novel methodology that will be utilized to study the effects of PHEV charging at the sub-transmission level. The proposed test platform utilizes the power hardware-in-the-loop (PHIL) concept in conjunction with high-fidelity PHEV energy system simulation models. The battery, in particular, is simulated utilizing a real-time digital simulator ($RTDS^{TM}$) which generates appropriate control commands to a power electronics-based voltage amplifier that interfaces via a LC-LC-type filter to a power grid. In addition, the PHEV impact is evaluated via another power electronic converter controlled through $dSPACE^{TM}$, a rapid control systems prototyping software.

• 디지털콘텐츠학회 논문지
• /
• 제8권3호
• /
• pp.371-376
• /
• 2007

차량 내부에서는 컨트롤러, 센서, 텔레매틱스 단말기, 내비게이션, 오디오 및 비디오 등 다양한 모듈들이 CAN이나 MOST와 같은 차량 네트워크를 통해 연결되어 있다. 게다가, 사용자는 이동 중에 무선 모바일 네트워크를 이용하여 ITS나 인터넷에 접속할 수도 있다. 이러한 네트워크의 다양한 활용은 데이터 해킹, 프라이버시 침해, 위치 추적 등과 같은 많은 보안 문제를 야기하게 된다. 또한, 차량 운영 데이터(센서, 제어 데이터)를 해킹함으로써 차량을 고장 내거나 사고를 유발할 수 있는 가능성도 점차 커지고 있다. 본 논문에서는 CAN이나 MOST와 같은 차량 네트워크에 적용할 수 있는 암호화 기능을 가지는 보안 모듈을 제안한다. 이 보안 모듈은 DES, 3-DES, SEED, ECC 및 RSA와 같은 일반적인 암호화 알고리듬과 전자서명 기능을 제공하게 된다.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.742-751
• /
• 2018

Electric vehicles (EV) are emerging as the future transportation vehicle reflecting their potential safe environmental advantages. Vehicle to Grid (V2G) system describes the hybrid system in which the EV can communicate with the utility grid and the energy flows with insignificant effect between the utility grid and the EV. The paper presents an optimal power control and energy management strategy for Plug-In Electric Vehicle (PEV) charging stations using Wind-PV-FC-Battery renewable energy sources. The energy management optimization is structured and solved using Multi-Objective Particle Swarm Optimization (MOPSO) to determine and distribute at each time step the charging power among all accessible vehicles. The Model-Based Predictive (MPC) control strategy is used to plan PEV charging energy to increase the utilization of the wind, the FC and solar energy, decrease power taken from the power grid, and fulfil the charging power requirement of all vehicles. Desired features for EV battery chargers such as the near unity power factor with negligible harmonics for the ac source, well-regulated charging current for the battery, maximum output power, high efficiency, and high reliability are fully confirmed by the proposed solution.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1321-1326
• /
• 2011

THE RAILWAY VEHICLE IS CONSISTS OF CARBODY, BOGIE AND WHEELSETS, EACH OF COMPONENTS IS CONNECTED WITH RIGID MASS, SPRING AND DAMPER. EACH OF COMPONENTS HAS TRANSLATION MOTIONS OF LONGITUDINAL (X AXIS), LATERAL (Y AXIS) AND VERTICAL (Z AXIS) DIRECTIONS, ROTATION MOTIONS OF X, Y, Z AXIS WHICH ARE NAMED ROLLING, PITCHING AND YAWING. THE VIBRATION MODE OF RAILWAY VEHICLE IS DIFFICULT TO FIND THE CHARACTERISTICS OF MOTION DURING THE OPERATION ON THE TRACK BECAUSE THESE HAPPEN TO INDEPENDENCE OR DUPLICATION MOTION CAUSED BY VEHICLE, WHEEL/RAIL AND TRACK IRREGULARITY ETC. IT IS NAMED AN ABNORMAL VIBRATION THAT THE VIBRATION, WHICH WAS PASSED THE PRIMARY AND SECONDARY SUSPENSION, IS AFFECTED TO THE PASSENGER WITHOUT DAMPING. THIS PAPER DESCRIBES AN EXPERIENCE EVALUATION TO FIND THE CAUSE OF AN ABNORMAL VIBRATION WHICH WAS HAPPEN AT OPERATING SPEED 60KPH ZONE DURING THE MAINLINE TEST.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1027-1034
• /
• 2011

Electronic devices in railway vehicle perform various functions such as not only braking and propulsion but also monitoring of vehicle condition, on-line diagnosis, and passenger information service, etc. These devices, distributed in vehicle, should be efficiently connected so as to properly perform the functions. IEC (International Electro-Technical Commission) standardized train communication network (TCN) as IEC 61375-1, -2. TCN can reduce the interconnecting work load by reducing the number of wire-line, compared with existing hard-wire connection, and it brings the efficient control by enabling various devices to share the information. But existing TCN can not satisfy the increasing service demands like passenger internet access and CCTV surveillance, etc. In this paper, we investigate ECN (Ethernet Consist Network) and ETN (Ethernet Train Backbone) which are proposed to satisfy these demands and in the process of standardization by IEC TC9 WG43.

• 대한임베디드공학회논문지
• /
• 제12권6호
• /
• pp.351-358
• /
• 2017

The most common communication interface for automotive electronic control devices is CAN (Controller Area Network). Sine CAN was first adopted to Daimler vehicles in 1991, all of automobile manufacturers use the CAN communication for in-vehicle networks. However, as the number of electronic control devices connected to the CAN network rapidly increases, the CAN protocol reaches the limit of technology. To overcome this limitation, Bosch introduced the new communication protocol, that is CAN-FD (Flexible Data-rate). In this paper, we analyze the characteristics and limitations of CAN-FD communication according to the topology under the in-vehicle wiring harness environment designed based on the existing classic CAN communication.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.73-74
• /
• 2016

This paper proposes a wide output range AC/DC converter for a rechargeable battery of electric vehicle. In the proposed wide output range AC/DC converter for rechargeable battery of electric vehicle, the main transformer in the DC/DC stage is divided by two. Therefore, if the switch is connected to the middle tap, then half of the maximum voltage is applied. Otherwise, it can be applied the full range of the high voltage by connecting the switch to the whole tab. And also, it is designed to have a wide output voltage range by applying Vin/2 made by changing the full-bridge to half-bridge by using the bridge change switch of the input stage. As it can be supplied the wide range output voltage with a single module, it has the advantage of space utilization and cost reduction effect.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.75-81
• /
• 1999

In this paper, the details of electronically controlled CVT is described , which Kia Motor company recently developed in prototype form for hybrid passenger car. This transmission has two input shafts, one for engine and the other for traction motor. The shaft for traction motor is located at rear side which is extended from primary pulley shaft and connected to traction motor through adapter gear box. Adopting two input system, various driving mode is available such as motor alone driving in hybrid vehicle application. As far as electrohydraulic system concerned , this transmission uses two bleed type variable force solenoids for line pressure and ratio control, and one on-off solenoid for clutch control. Another feature for this transmission is that oil pump for transmission is separate from CVT for supplying oil pressure even at vehicle standstill.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.92-99
• /
• 2012

It is often thought that because no-start motor vehicles cannot start an engine, a fire cannot occur for motor vehicle causes. However, although the engine cannot start up, some parts may be live with electricity if a battery is connected. If the parts have problems, a fire can occur. This study analyzed the causes of fires occurring when a motor vehicle was loaded onto a tow truck to service no-start. It is suggested that no-start motor vehicles should separate a battery terminal to prevent a fire. And this fire is related to automotive products liability.

• International Journal of Automotive Technology
• /
• 제7권7호
• /
• pp.769-776
• /
• 2006

A mathematical model is developed in this paper to define the interaction between the occupant and vehicle passenger compartment and to predict the occupant dynamic response during a sudden impulse load. Two different types of occupants are considered in this study, child and adult occupants. The occupants are considered as lumped masses connected to the child seat and vehicle's body masses by means of restraint systems. In addition, the occupant restraint characteristics of seat belt and airbag are represented by stiffness and damping elements. To obtain the dynamic response of the occupant, the equations of motion of the occupants during vehicle collisions are developed and analytically solved. The occupant's acceleration and relative displacement are used as injury criteria to interpret the results. It is demonstrated from the numerical simulations that the dynamic response and injury criteria are easily captured and analyzed. It is also shown that the mathematical models are flexible, useful in optimization studies and it can be used at initial design stage.