• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제22회 KOSCI SYMPOSIUM 논문집
• /
• pp.9-16
• /
• 2001

When large size nozzle with low jet velocity is used, the buoyancy effect arises from the density difference among propane, air, and burnt gas. Flame characteristics in such buoyant jets have been investigated numerically to elucidate the effect of buoyancy on lifted flames. It has been demonstrated that the cold jet has circular cone shape since upwardly injected propane jet decelerates and forms stagnation region. In contrast to the cold flow, the reacting flow with a lifted flame has no stagnation region by the buoyancy force induced from the burnt gas. To further illustrate the buoyancy effect on lifted flames, the reacting flow with buoyancy is compared with non-buoyant reacting flow. Non-buoyant flame is stabilized at much lower height than the buoyant flame. At a certain range of fuel jet velocities and fuel dilutions. an oscillating flame is demonstrated numerically showing that the height of flame base and tip vary during one cycle of oscillation. Under the same condition. non-buoyant flame exhibits only steady lifted flames. This confirms the buoyancy effect on the mechanism of lifted flame oscillation.

• 한국가시화정보학회지
• /
• 제16권3호
• /
• pp.40-46
• /
• 2018

The surface structure of the electrospun polymer fibers depends on the polymer concentration, the type of solvent used, applied voltage and so on. To make a desired surface, it is important to understand the effects of the physicochemical properties to form a stable Taylor cone and jet dispensation. We observed the formation of Taylor cone and a consequent structure of fiber by controlling the parameters of applied voltage, solution concentration, solvent and collector effectively. Once the surfaces were fabricated, the structures were analyzed using optical imaging technologies. As the solution concentration was increased, the smooth fibers were formed. In addition, different solvent ratios determined the viscosity and the surface tension of solutions. As a result, with decreased viscosity and increased surface tension, thin fibers were obtained by electrospinning. Furthermore the aligned nanofiber was successfully created by using drum collector.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.351-352
• /
• 2009

On-demand ejection of ultra-fine droplets that uses both electrohydrodynamic (EHD) force and mechanical actuation is presented. The liquid meniscus was controlled by a piezoelectric actuator and droplets were ejected by EHD force. Through these effects, it was possible to obtain a high operational jetting frequency of 5kHz with a short delay-time (about 50 us) when compared with existing on-demand EHD jetting methods, such as the pulsating jet mode (3-10 msec) and the pulsed-voltage cone-jet mode(3.6 msec). Also, we obtained ultra-fine droplets at a volume that was at the femto-liter level simultaneously. The jetting characteristics were examined for both hydrophobicity and hydrophilicity of the surface of a capillary.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.86-93
• /
• 2012

The effects of projectile impact system on the transient spray characteristic which is supersonic liquid tip velocity were studied by experimentally. Supersonic liquid jets were generated by impact of a high speed projectile driven by a Two-stage light gas gun. A high speed camera and schlieren optical system were used to capture the spray structures of the supersonic liquid jets. In a case of nozzle assembly Type-A, expansion gases accelerate a projectile which has a mass of 6 grams from 250 m/s at the exit of the launch tube. Accelerated projectile collides with the liquid storage part, then supersonic liquid jets are injected with instantaneous spray tip velocity from 617.78 m/s to 982.54 m/s with various nozzle L/d. However, In a case of nozzle assembly Type-B which has a heavier projectile (60 grams) and lower impact velocity (182 m/s), an impact pressure was decreased. Thus the liquid jet injected at 210 m/s of the maximum velocity did not penetrate a shock wave and fast break-up was occurred. Pulsed injection of liquid column generated second shock wave and multiple shock wave.

• 한국가스학회지
• /
• 제24권1호
• /
• pp.49-55
• /
• 2020

산업용 혹은 발전용 가스터빈에 사용되는 이중 콘형 예혼합 연소기의 다단 연소 특성을 이해하기 위하여 실험적연구를 수행하였다. 이를 위하여 기존에 모두 경사면에 공급되는 연료를 콘부분으로 일부 할애하는 방식으로 다단연소 방식을 구성하였으며 콘에서 분사되는 연료공급은 축방향과 콘 경사면 방향으로 하였다. 다단연소 연소특성을 이해하기 위하여 콘에서의 연료 분사 방향과 연료 분배율 변화에 대한 NOx와 CO의 배출 농도 그리고 벽면 온도분포를 측정하였다. 그 결과 총 연료에 대한 콘으로의 분배율이 3%인 경우 콘에서의 연료 분사방향에 관계없이 노즐내의 예혼합 영역에서 연료가 공기와 균일하게 혼합됨으로서 연소영역의 고온점 감소에 의하여 NOx 배출 농도가 감소된다. 그러나 콘에서 축방향으로 분사되는 연료분배율이 8%로 증가하는 경우 노즐 내부 예혼합 영역으로의 화염 역화로 인하여 NOx의 배출농도가 오히려 증가하게 된다.

• Journal of Mechanical Science and Technology
• /
• 제16권8호
• /
• pp.1135-1143
• /
• 2002

The intermittent spray characteristics of the single-hole diesel nozzle (d$\sub$n/=0.32 mm) used in the fuel injection system of heavy-duty diesel engines were experimentally investigated. The mean velocity and turbulent characteristics of the diesel spray injected intermittently into the still ambient were measured by using a 2-D PDPA (phase Doppler particle analyzer) . The gradient of spray half-width linearly increased with time from the start of injection, and it approximated to 0.04 at the end of the injection. The axial mean velocity of the fuel spray measured along the radial direction was similar to that of the free air jet within R/b= 1.0-1.5 regardless of elapsing time, and its non-dimensional distribution corresponds to the theoretical velocity distributions suggested by Hinze in the downstream of the spray flow fields. The turbulent intensity of the axial velocity components measured along the radial direction represented the 20-30% of the U$\sub$cι/ and tended to decrease in the outer region. The turbulent intensity in the trailing edge was higher than that in the leading edge.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.100-106
• /
• 2001

The size distributions of electrospray droplets from the Taylor cone in cone-jet mode are directly measured by using a freezing method and a transmission electron microscope (TEM) image processing technique. These results are compared with the data obtained by an aerodynamic size spectrometer (TSI Aerosizer DSP). The use of glycerol seeded with NaI and a freezing method make it possible to sample droplets with their original sizes preserved. Since pictures of droplets are taken with TEM with very low vapor pressure of the solution, evaporation is suppressed by freezing. For liquid flow rates below 1 nl/sec, the measured droplet diameters by the TEM image processing technique and the aerosizer are in the range of 0.25 to $0.32{\mu}m$ and 0.30 to $0.40{\mu}m$, respectively. Comparing the TEM data with the aerosizer measurements, it has been revealed that the TEM image processing technique can afford more accurate values of droplet size distributions in the submicron range of 0.1 to $0.4{\mu}m$.

• 한국분무공학회지
• /
• 제16권1호
• /
• pp.44-50
• /
• 2011

An object of this study is to understand the correlation of injection characteristics and injector dimensions according to biodiesel mixture. The Injection characteristics of different types of common-rail injectors are the number of nozzle holes (5~8), jet cone angle ($146^{\circ}{\sim}153^{\circ}$), hydraulic flow rate (830~900 ml/min) injection quantity and response time. Prior to characteristic experiment, the reference injector has been selected in 6 candidates injectors under the investigation of injected quantity according to the biodiesel mixture so that injector type can be determined. The injector is used for the characteristic experiment which varied the various operating conditions including pressure 23 MPa, 80 MPa, 160 MPa, changing in injection duration 0.16 ms~1.2 ms and even mixture ratio. The result shows that the nozzle hole number and cone angle influence the injection quantity much more than nozzle hole diameter at low injection pressure and the nozzle hole diameter at high injection pressure, post injection duration.

• 한국추진공학회지
• /
• 제18권3호
• /
• pp.34-39
• /
• 2014

center-body디퓨져에 대한 형상 설계 요소를 분석하고 수치적 기법을 통한 설계형상 변수를 구성하였다. 수치기법으로는 Center-body 디퓨져의 내부유동해석을 위하여 2차원 축대칭 Navier-Stokes equation와 $k-{\epsilon}$ 난류모델을 사용하였다. 또한 center-body디퓨져의 시동압력과 진공도 및 형상설계변수에 대해서 2차목 디퓨져와 비교하였다. 냉각시스템의 성능향상 방안으로 CBD의 원추선단에 역류제트를 활용한 TPS시스템의 개념을 제시하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.583-586
• /
• 2017

마이크로 터보제트엔진을 이용하여 S형상 배기노즐의 플룸의 적외선 신호 특성을 이해하기 위하여 적외선 신호 특정 연구를 수행하였다. 엔진 배기노즐은 원형노즐과 가로세로비가 5인 사각형 노즐 그리고 가로세로비가 5.2인 S형상의 배기노즐을 제작하여 실험을 수행하였다. 배기가스에서 방출되는 적외선 신호는 가로세로비가 클수록 적외선 신호의 크기가 점차 감소하는 경향을 보였고 배기노즐의 형상이 S형상의 경우 사각형 노즐 보다 적외선 신호가 28.4% 감소하는 것을 확인하였다.