• Korean Journal of Food Science and Technology
• /
• v.29 no.3
• /
• pp.492-496
• /
• 1997

Purple sweet potato pigment extract was concentrated using both membrane separation method and vacuum concentration method. The pigment extract (anthocyanin content 1.6 g/L) was concentrated $({\times}25)$ after 5 hr of continuous operation of a nanofiltration to get anthocyanin content of 10.6 g/L. Total solid content also increased continuously while the flux decreased continuously during the concentration process. Degradation index (DI) changes of concentrated pigment solution were insignificant during the whole concentration process which is indicating that the nanofiltration method does not affect color degradation of anthocyanin pigment. For the comparison test, the same pigment extract was concentrated using a rotary vacuum evaporator at temperatures of 40 and $60^{\circ}C$. At both temperatures, pigment content increased in a similar manner during concentration $({\times}5)$. However, DI value at $60^{\circ}C$ increased while that at $40^{\circ}C$ did not change appreciably. Total color difference value changed only slightly by nanofiltration and $40^{\circ}C$ while changed significantly by $60^{\circ}C$. These indicate that a membrane filtration method is more effective in concentrating purple sweet potato pigment extract than a vacuum concentration method by high temperature.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.4
• /
• pp.303-310
• /
• 2017

Pressure retarded osmosis(PRO) has attracted much attention as potential technology to reduce the overall energy consumption for reverse osmosis(RO) desalination. The RO/PRO hybrid process is considered as the most logical next step for future desalination. The PRO process aims to harness the osmotic energy difference of two aqueous solutions separated by a semipermeable membrane. By using the concentrated water(RO brine) discharged from existing RO plants, the PRO process can effectively exploit a greater salinity gradient to reduce the energy cost of processing concentrated water. However, in order to use RO brine as the draw solution, PRO membrane must have high water flux and enough mechanical strength to withstand the high operational pressure. This study investigates the development of a thin film composite PRO membrane and spiral wound module for high power density. Also, the influence of membrane backing layer on the overall power density was studied using the characteristic factors of PRO membranes. Finally, the performance test of an 8-inch spiral wound module was carried out under various operating conditions(i.e. hydraulic pressure, flow rate, temperature). As the flow rate and temperature increased under the same hydraulic pressure, the PRO performance increased due to the growth of water permeability coefficient and osmotic pressure. For a high performance PRO system, in order to optimize the operating conditions, it is highly recommended that the flow pressure be minimized while the flow rate is maintained at a high level.

• Journal of Korean Society on Water Environment
• /
• v.37 no.6
• /
• pp.442-448
• /
• 2021

Seawater desalination is a technology through which salt and other constituents are removed from seawater to produce fresh water. While a significant amount of fresh water is produced, the desalination process is limited by the generation of concentrated brine with a higher salinity than seawater; this imposes environmental and economic problems. In this study, characteristics of seawater from three different locations in South Korea were analyzed to evaluate the feasibility of crystallization to seawater desalination. Organic and inorganic substances participating in crystal formation during concentration were identified. Then, prediction and economic feasibility analysis were conducted on the actual water flux and obtainable salt resources (i.e. Na2SO4) using membrane distillation and energy-saving crystallizer based on multi-stage flash (MSF-Cr). The seawater showed a rather low salinity (29.9~34.4 g/L) and different composition ratios depending on the location. At high concentrations, it was possible to observe the participation of dissolved organic matter and various ionic substances in crystalization. When crystallized, materials capable of forming various crystals are expected. However, it seems that different salt concentrations should be considered for each location. When the model developed using the Aspen Plus modular was applied in Korean seawater conditions, relatively high economic feasibility was confirmed in the MSF-Cr. The results of this study will help solve the environmental and economic problems of concentrated brine from seawater desalination.

• Korean Journal of Food Science and Technology
• /
• v.29 no.2
• /
• pp.279-283
• /
• 1997

Membrane separation technology was applied to prepare high quality persimmon juice from persimmon, which is produced in large quantities in Korea. The influences of time, pressure, and temperature on permeate flux were studied during concentration by reverse osmosis. The chemical components of retentate were also analyzed. The permeate flux was higher as the operating temperature and pressure were increased, and was influenced more strongly by operating pressure than temperature. Maximum concentration by reverse osmosis employed in this study in the oBrix scale was about 30. Retention percentage of sugar in the persimmon juice which was concentrated by membrane separation system was more than 90% and was not influenced by operating conditions. Retention percentage of volatile components in the same process was more than 60%; it was increased as operating temperature was decreased and pressure was increased.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.227-232
• /
• 2008

Stirling engine for solar thermal power is an essential part of Dish-Stirling system which generates electricity by using direct normal irradiation and will go into commercialization in near future. For the Stirling engine used in this study is Solo 161 model the capacity of which is 10 kWe and was already used for the Dish-Stirling system of KIER in Jinhae. The receiver of Stirling engine absorbes concentrated solar radiation and transfer it to working fluid of Hydrogen. The working condition of striling engine is high temperature and high pressure to make high efficiency. Therefore the receiver should stand against high temperature of above 800 $^{\circ}C$ and high pressure of max. 150 bar with good performance of heat transfer. The receiver is composed of 78 Inconel tubes of 1/8" with thickness of 0.71 mm and two reserviors which is connected with two cylinders. In order to know the charaterristics of heat transfer of Stirling engine receiver, simulation on the heat transfer of the receiver of Solo 161 is conducted by using CFD code of Fluent. The heat flux on the receiver surface has a shape of Gaussian distribution so, it is necessary to simulate a whole receiver. However, It is difficult and time consuming to simulate the whole receiver that one tube with different heat flux conditions are considered in this study. From the simulation results, heat transfer charateristics of receiver are observed and tube wall and fluid temperature and heat transfer coefficient are obtained and compared with the calculated results from Dittus-Boelter's correlation.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.17 no.4
• /
• pp.371-375
• /
• 1988

Tubular ultrafiltration membranes were used to investigated mass transfer characteristics of waste cheese whey. The effects of bulk concentration and flow velocity on permeat flux, mass transfer coefficient and apparent rejection coefficient were measured. Mass transfer coefficient was increased linearly with increasing flow velocity, and following relationship between mass transfer coefficient(k) and linear velocity(u) was obtained. $k=0.87{\times}10^{-5}u^{1-1}$ It is interjecting to note that plots for all linear velocity tend to converge to the same point for zero permeating flux, and the maximum bulk concentration that can be achieved with cheese whey extracts was 38(w/v %). In general, membrane rejection coefficient increased with increasing flow velocity and the rejection coefficients of cheese whey solution and that of lactose in cheese whey solution were obtained $0.40{\sim}0.65$, $0.15{\sim}0.30$, respectively.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.294-303
• /
• 2011

In this paper an effective five-phase induction motor (IM) and its drive methods are proposed. Due to the additional degrees of freedom, the five-phase IM drive presents unique characteristics for enhancing the torque producing capability of the motor. Also the five-phase motor drives possess many other advantages when compared to traditional three-phase motor drives. Some of these advantages include, reducing the amplitude and increasing the frequency of the torque pulsation, reducing the amplitude of the current without increasing the voltage per phase and increasing the reliability. In order to maximize the torque per ampere, the proposed motor has concentrated winding, the produced back electromotive force (EMF) is almost trapezoidal, and the motor is supplied with the combined sinusoidal plus the third harmonic of the currents. For demonstrating the superior performance of the proposed five-phase IM, the motors are also analyzed on the synchronously rotating reference frame. To supply trapezoidal current waveform and to exclude the effect of the $3^{rd}$ harmonic current, a new control stratagem is proposed. The proposed control method is based on direct torque control (DTC) and rotor flux oriented control (RFOC) of the five-phase IM drives. It is able to reduce the acoustical noise, the torque, the flux, the current, and the speed pulsations during the steady state. The DTC transient merits are preserved, while a better quality steady-state performance is produced in the five phase motor drive for a wide speed range. Experimental results clearly demonstrated a more dynamic steady state performance with the proposed control system.

• Membrane and Water Treatment
• /
• v.10 no.2
• /
• pp.165-178
• /
• 2019

Mixed matrix membranes (MMMs) of poly (vinyl alcohol) (PVA) containing certain amounts of H-${\beta}$ zeolite for pervaporation were manufactured by using a solution casting protocol. These zeolite-embedded membranes were then characterized with scanning electron microscope (SEM), X-ray diffraction (XRD) and swelling tests. The membrane separation performance has been examined by means of isopropanol (IPA) dewatering from its highly concentrated aqueous solutions via response surface methodology (RSM). The results have demonstrated that the influences of feed IPA composition (85-95 wt.%), feed temperature ($50-70^{\circ}C$), zeolite loading (15-25 wt.%) and their interactive influences are all statistically significant on both pervaporation flux ($398-1228g/m^2{\cdot}h$) and water/isopropanol separation factor (617-2001). The quadratic models based on the RSM analysis have performed excellently to correlate experimental data with very high determination coefficients and very low relative standard deviations. The optimal pervaporation predictions given by using the RSM models demonstrate a total flux of $953g/m^2{\cdot}h$ and separation factor of 1458, and are excellently verified by experimental results. As reflected by these results, PVA MMMs embedded with hydrophilic $H-{\beta}$ zeolite entities have performed considerably better than its pure counterpart and indicated great potential for isopropanol dehydration applications.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.10
• /
• pp.1609-1612
• /
• 2006

The determination of the boron isotopic ratio in solutions was achieved by means of a solid state track detector by using an alpha track. The neutron flux was optimized by using a Cd-foil to find the optimum conditions for counting the number of alpha tracks on the selected solid detector caused by the (n, $\alpha$) nuclear reaction of boron. The home-made multi-dot detector plate was utilized in this study to increase the reproducibility of the measurement by uniformly drying the boron solution within the marked circle area on the detector plate. The experimental results of this study verified that the $^{11}B/^{10}B $ isotopic ratio can be measured by observing the number of alpha tracks for different concentrated standard solutions with various isotopic compositions. This technique was applied to the determination of $^{10}B$ enrichment factor in a biological sample for a boron neutron capture therapy.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.88.1-88.1
• /
• 2013

We have investigated vertical motions of plasma in the pores and changes of the motions with height by using high time and spatial resolutions data obtained by the Fast Imaging Solar Spectrograph (FISS) of the 1.6 meter New Solar Telescope (NST). We infer the LOS velocity by applying the bisector method to the wings of CaII 854.2 nm line profile. We find that (1) upflow velocity in the pores decreases with height and turns into downward in the upper chromosphere; (2) 3 min and 5 min oscillations are found from the Doppler velocity in the pore at various wavelengths from the wing (${\pm}2.35{\AA}$) to the core (${\pm}1.25{\AA}$) of the CaII line; and (3) power of high (low) frequency oscillation obtained from the CaII intensity increases (decreases) with height. We discuss the physical implications of our results in view of the connection of LOS plasma flows in a concentrated magnetic flux (pore) between the photosphere and the low chromosphere.