• 제목/요약/키워드: Computer simulation method

검색결과 4,358건 처리시간 0.039초

황해 중동부 제4기 퇴적층의 지음향 특성 (Geoacoustic characteristics of Quaternary stratigraphic sequences in the mid-eastern Yellow Sea)

  • 진재화;장성형;김성필;김현태;이치원;장정해;최진혁;양우헌
    • 한국해양학회지:바다
    • /
    • 제6권2호
    • /
    • pp.81-92
    • /
    • 2001
  • 황해 중동부 해역 ($36^{\circ}00'N{\sim}36^{\circ}45'N$,$\;125^{\circ}00'E{\sim}125^{\circ}45'E$)에 분포하는 퇴적층을 대상으로 획득한 고해상 탄성파탐사자료(에어건, 스파커, SBP)와 심부 시추시료(YSDP 105, ${\sim}$64m 깊이)의 종합분석에 따라, 연구 해역의 층서모델을 설정하고 탄성 -음향 모델링을 수행하였다. 층서모델은 탄성파${\cdot}$${\cdot}$시 층서 단위들을 비교 분석하여 각 지층단위의 음향학적 특성, 퇴적과정, 생성시기를 규명하였다 또한 단위층 형성과정을 해수면 변동과 관련지어 순차층서를 복원하였다. 각 순차층은 육성 또는 천해성 기원이며 조립질의 저해수면 퇴적계와 조석 기원 세립질의 해침-고해수면 퇴적계로 구성되어 있다. 탄성-음향 모델링의 매개변수 산출을 위해, 0.S~90 cm 심도 간격으로 측정된 시추코아의 121 개 평균입도 자료를, Hamilton의 회귀식과 퇴적심도에 따른 변화구배를 이용하여, 전밀도(bulk density)값과 종파속도값으로 변환${\cdot}$계산하였다. 외삽${\cdot}$보정된 121 쌍의 전밀도${\cdot}$종파속도 물성값은 설정된 층서모델에서 제시된 단위층 별로 평균하여 각 단위층의 대표값으로 산출하였다. 퇴적층 내의 탄성-음향 전파 모델링을 위해, 층서모델의 각 단위층에 전밀도와 종파속도의 대표값을 입력 매개변수값으로 부여한 후, 층서 구성 단위층들을 유한요소격자로 분해하였다. 파선추적법의 컴퓨터 모델링 결과, 탄성-음향의 전파는 층서모델을 구성하는 단위층 경계면의 불규칙성과 저속도층의 다수 존재에 의하여 매우 복잡한 음경로를 보이며, 음원의 위치에 따라 탄성-음파의 암영대가 달리 존재함을 확인하였다. 것으로 보아 층 2는 고에너지환경에서 형성되었음을 시사한다. 또한 층 2에서 Al의 증가는 쇄설기원 물질의 유입에 의한 것으로 추정된다. 플라이오세 이후에 형성된 층 1은 치밀한 조직을 보이며, 형성 이후 속성작용을 받지 않았다.선택적으로 분해되는 것으로 여겨진다.두냔 tsuchigae, S. nigripinni morii, M. jeoni, C. splendidus, P. koreanus, C. lutheri, I. koreensis, C. herzi, R. brunneus 등으로 본 종들의 서식 상태는 하천의 오염 정도 및 하천개수와 직접적인 관계가 있으므로 어류서식 환경을 유지시키기 위해서 보다 적극적인 하천 수질관리의 대책과 방안이 수립되어야 될 것으로 사료된다.와 운동, H-R도상에서의 별의 특성과 진화 등이다. 탐구 과정에 대한 학생의 성취도는 비교적 높으므로 이해도가 상대적으로 낮은 영역에 대해 학생의 오답 유형을 참고하여 기본 개념 지도에 보다 관심을 기울일 필요가 있다.Cr은 FW에서 전반적으로 감소하는 경향을 보였지만 SW에서는 실험 초기에 감소하다 24시간 이후에는 증가 후 일정한 양상을 보였다. Pb은 FW에서 전반적으로 감소했지만 SW에서는 초기에 급격히 증가 후 다시 급격히 감소하는 양상을 보였다 Pb 또한 Cu, Cd, As와 마찬가지로 SW1&2에서 제거속도가 가장 빠르게 나타났다. FW 상층수 중 Hg는 시간에 따라 급격히 감소했고, 제거속도는 Fw5&6에서 가장 느렸다. 이러한 결과에 근거할 때 벼가 자라고 있고 이분해성 유기물이 풍부한 FW1&2, FW3&4 토양과 상층수에서는 유기물의 분해 활동이 활발하였지만, 벼가 경작되지 않는 FW5&6과 SW 에서는 유기물이 상대적으로 결핍되어 유기물의 분해활동이 적었을 것으로 판단된다. 한편, 수조에 인위적으로 유기물을 첨가한 경우 박테리아 세포수는 SW1에서 164시간 동안 4배 증가하였으나 SW3과 SW5에서는 각각 2.7배, 1.

  • PDF

Center Array-Sequencing 위상펼침 기법의 MR 온도영상 적용에 관한 기초연구 (Preliminary Study on the MR Temperature Mapping using Center Array-Sequencing Phase Unwrapping Algorithm)

  • ;김태형;천송이;한용희;최기승;이광식;전재량;은충기;문치웅
    • Investigative Magnetic Resonance Imaging
    • /
    • 제12권2호
    • /
    • pp.131-141
    • /
    • 2008
  • 목적: 물체 내부의 온도를 비침습적으로 측정할 수 있는 양성자 공명 주파수 이동에 의한 MR 온도영상의 재구성에 center array-sequencing 위상펼침(PU) 기법을 적용시켜 그 성능 및 유용성을 평가하고자 하였다. 대상 및 방법: MR 온도 영상에 앞서 잡음 수준이 다른 타원형 팬텀들을 컴퓨터 모의 실험으로 제작하고 제안된 PU방 법을 적용시켜 잡음에 대한 성능을 평가하였다. MR 실험은 PU 실험과 이를 이용한 온도분포영상획득 실험으로 구분하여 수행되었다. 1.5T MR 영상장치에서 무릎코일과 $T2^*$ 경사자장에코 펄스열을 이용하여 MR 영상을 얻었다. 물통, 오렌지, 아가젤 등의 팬텀을 실험 대상으로 하였고 자체 제작된 온수펌프 장치로 팬텀의 온도를 조절하였다. T 형 열전쌍 온도측정장치로 팬텀 온도를 측정하고 MR 온도영상 결과와 비교하였다. 획득된 MR영상의 위상분포는 제안된 PU방법으로 위상을 편 후 온도분포 영상을 재구성하였다. 가열 전 후의 온도변화와 MR 영상의 위상변화 관계를 이용하여 아가젤 팬텀 내의 MR온도분포 영상을 구하였다. 결과: 제안된 center array-sequencing PU 알고리즘을 이용하여 여러 팬텀에 대한 MR 위상영상의 접힘 현상을 기존 방법보다 간편하고 빠르게 제거할 수 있었고 이를 이용하여 MR 온도영상을 획득할 수 있었다. 결론: 본 연구는 제안된 center array-sequencing 위상펼침 방법이 잡음에 강하고 처리 속도가 빠를 뿐만 아니라 양성자 공명 주파수 이동의 성질을 이용한 MR 온도 영상 획득에 성공적으로 적용될 수 있음을 보였다.

  • PDF

컨테이너 보안 검색용 9 MeV 전자 선형가속기에서 발생한 방사화 특성평가에 관한 연구 (A Study on Activation Characteristics Generated by 9 MeV Electron Linear Accelerator for Container Security Inspection)

  • 이창호;김장오;이윤지;전찬희;이지은;민병인
    • 한국방사선학회논문지
    • /
    • 제14권5호
    • /
    • pp.563-575
    • /
    • 2020
  • 본 연구 목적은 컨테이너 보안 검색용 선형가속기에서 발생하는 방사화 특성을 평가하는 것이다. 전산모사 설계는 첫째, 표적은 텅스텐(Z=74) 단일물질 표적 및 텅스텐(Z=74)과 구리(Z=29) 복합물질 표적으로 구성하였다. 둘째, 부채꼴(Fan beam) 조준기는 물질에 따라 납(Z=82) 단일 물질과 텅스텐(Z-74)과 납(Z=82)의 복합물질로 구성하였다. 셋째 선형가속기가 위치한 방(Room)의 콘크리트는 Magnetite type 및 불순물(Impurity)을 포함하였다. 연구 방법은 첫째, MCNP6 코드를 이용하여 선형가속기 및 구조물을 F4 Tally로 광중성자 플럭스(Flux)를 계산하였다. 둘째, MCNP6 코드에서 계산된 광중성자 플럭스를 FISPACT-II에 적용하여 방사화 생성물을 평가하였다. 셋째, 방사화 생성물의 비방사능을 통해 해체 평가를 진행하였다. 그 결과 첫째, 광중성자 분포는 표적에서 가장 높게 나왔으며, 조준기 및 10 cm 깊이의 콘크리트 순으로 나타났다. 둘째, 방사화 생성물은 텅스텐 표적 및 조준기에서 W-181, 불순물이 포함된 콘크리트에서 Co-60, Ni-63, Cs-134, Eu-152, Eu-154 핵종이 부산물(by-product)로 생성되었다. 셋째, 해체 시 텅스텐 표적은 90일 이후 자체 처분 허용 농도를 만족하는 것으로 보였다. 이러한 결과는 9 MeV 에너지에서의 광중성자 수율(Yield) 및 방사화 정도가 미미한 것으로 확인할 수 있었다. 하지만, 선형가속기 텅스텐 표적 및 조준기에서 발생한 W-181은 수리를 위한 분해 시 피폭의 영향을 줄 수 있을 것으로 생각된다. 따라서, 본 연구는 컨테이너 보안검색용 선형가속기 방사화된 부품관리에 관한 기초 자료를 제시한 것이다. 또한, 컨테이너 보안 검색용 선형 가속기 해체 시 자체처분을 만족하는 농도 기준을 입증하는데 활용될 수 있을 것으로 기대한다.

우리나라 연안화물선의 적정선복량 추정에 관한 연구 (A Study on Estimating Optimal Tonnage of Coastal Cargo Vessels in Korea)

  • 이청환;이철영
    • 한국항해학회지
    • /
    • 제13권1호
    • /
    • pp.21-53
    • /
    • 1989
  • In the past twenty years, there has been a rapid increase in the volume of traffic in Korea due to the Korean great growth of the Korean economy. Since transformation provides an infrastructure vital to economic growth, it becomes more and more an integral part of the Korea economy. The importance of coastal shipping stands out in particular, not only because of the expansion limit on the road network, but also because of saturation in the capacity of rail transportation. In spite of this increase and its importance, coastal shipping is falling behind partly because it is givenless emphasis than ocean-going shipping and other inland transportation systems and partly because of overcompetition due to excessive ship tonnage. Therefore, estimating and planning optimum ship tonnage is the first take to develop Korean coastal shipping. This paper aims to estimate the optimum coastal ship tonnage by computer simulation and finally to draw up plans for the ship tonnage balance according to supply and demand. The estimation of the optimum ship tonnage is peformed by the method of Origin -Destimation and time series analysis. The result are as follows : (1) The optimum ship tonnage in 1987 was 358, 680 DWT, which is 54% of the current ship tonnage (481 ships, 662, 664DWT) that is equal to the optimum ship tonnage in 1998. this overcapacity result is in excessive competition and financial difficulties in Korea coastal shipping. (2) The excessive ship tonnage can be broken down into ship types as follows : oil carrier 250, 926 DWT(350%), cement carrier 9, 977 DWT(119%), iron material/machinery carrier 25, 665 DWT(117%), general cargo carrier 17, 416DWT(112%). (3) the current total ship crew of 5, 079 is more than the verified optimally efficient figure of 3, 808 by 1271. (4) From the viewpoint of management strategy, it is necessary that excessive ship tonnage be reduced and uneconomic outdated vessels be broken up. And its found that the diversion into economically efficient fleets is urgently required in order to meet increasing annual rate in the amounts of cargo(23, 877DWT). (5) The plans for the ship tonnage balance according to supply and demand are as follows 1) The establishment of a legislative system for the arrangement of ship tonnage. This would involve; (a) The announcement of an optimum tonnage which guides the licensing of cargo vessels and ship tonnage supply. (b) The establishment of an organization that substantially arrangement tonnage in Korea coastal shipping. 2) The announcement of an optimum ship tonnage both per year and short-term that guides current tonnage supply plans. 3) The settlement of elastic tariffs resulting in the protect6ion of coastal shipping's share from other tonnage supply plans. 4) The settlement of elastic tariffs resulting in the protection of coastal shipping's share from other transportation systems. 4) Restriction of ocean-going vessels from participating in coastal shipping routes. 5) Business rationalization of coastal shipping company which reduces uneconomic outdated vessels and boosts the national economy. If we are to achieve these ends, the followings are prerequisites; I) Because many non-licensed vessels are actually operating and threatening the safe voyage of the others in Korea coastal routes, it is necessary that those ind of vessels be controlled and punished by the authorities. II) The supply of ship tonnage in Korean coastal routes should be predently monitored because most of the coastal vessels are to small to be diverted into ocean-going routes in case of excessive supply. III) Every ship type which is engaged in coastal shipping should be specialized according to the characteristics of its routes as soon possible.

  • PDF

토양수분함량 예측 및 계획관개 모의 모형 개발에 관한 연구(I) (A Study on the Development of a Simulation Model for Predicting Soil Moisture Content and Scheduling Irrigation)

  • 김철회;고재군
    • 한국농공학회지
    • /
    • 제19권1호
    • /
    • pp.4279-4295
    • /
    • 1977
  • Two types of model were established in order to product the soil moisture content by which information on irrigation could be obtained. Model-I was to represent the soil moisture depletion and was established based on the concept of water balance in a given soil profile. Model-II was a mathematical model derived from the analysis of soil moisture variation curves which were drawn from the observed data. In establishing the Model-I, the method and procedure to estimate parameters for the determination of the variables such as evapotranspirations, effective rainfalls, and drainage amounts were discussed. Empirical equations representing soil moisture variation curves were derived from the observed data as the Model-II. The procedure for forecasting timing and amounts of irrigation under the given soil moisture content was discussed. The established models were checked by comparing the observed data with those predicted by the model. Obtained results are summarized as follows: 1. As a water balance model of a given soil profile, the soil moisture depletion D, could be represented as the equation(2). 2. Among the various empirical formulae for potential evapotranspiration (Etp), Penman's formula was best fit to the data observed with the evaporation pans and tanks in Suweon area. High degree of positive correlation between Penman's predicted data and observed data with a large evaporation pan was confirmed. and the regression enquation was Y=0.7436X+17.2918, where Y represents evaporation rate from large evaporation pan, in mm/10days, and X represents potential evapotranspiration rate estimated by use of Penman's formula. 3. Evapotranspiration, Et, could be estimated from the potential evapotranspiration, Etp, by introducing the consumptive use coefficient, Kc, which was repre sensed by the following relationship: Kc=Kco$.$Ka+Ks‥‥‥(Eq. 6) where Kco : crop coefficient Ka : coefficient depending on the soil moisture content Ks : correction coefficient a. Crop coefficient. Kco. Crop coefficients of barley, bean, and wheat for each growth stage were found to be dependent on the crop. b. Coefficient depending on the soil moisture content, Ka. The values of Ka for clay loam, sandy loam, and loamy sand revealed a similar tendency to those of Pierce type. c. Correction coefficent, Ks. Following relationships were established to estimate Ks values: Ks=Kc-Kco$.$Ka, where Ks=0 if Kc,=Kco$.$K0$\geq$1.0, otherwise Ks=1-Kco$.$Ka 4. Effective rainfall, Re, was estimated by using following relationships : Re=D, if R-D$\geq$0, otherwise, Re=R 5. The difference between rainfall, R, and the soil moisture depletion D, was taken as drainage amount, Wd. {{{{D= SUM from { {i }=1} to n (Et-Re-I+Wd)}}}} if Wd=0, otherwise, {{{{D= SUM from { {i }=tf} to n (Et-Re-I+Wd)}}}} where tf=2∼3 days. 6. The curves and their corresponding empirical equations for the variation of soil moisture depending on the soil types, soil depths are shown on Fig. 8 (a,b.c,d). The general mathematical model on soil moisture variation depending on seasons, weather, and soil types were as follow: {{{{SMC= SUM ( { C}_{i }Exp( { - lambda }_{i } { t}_{i } )+ { Re}_{i } - { Excess}_{i } )}}}} where SMC : soil moisture content C : constant depending on an initial soil moisture content $\lambda$ : constant depending on season t : time Re : effective rainfall Excess : drainage and excess soil moisture other than drainage. The values of $\lambda$ are shown on Table 1. 7. The timing and amount of irrigation could be predicted by the equation (9-a) and (9-b,c), respectively. 8. Under the given conditions, the model for scheduling irrigation was completed. Fig. 9 show computer flow charts of the model. a. To estimate a potential evapotranspiration, Penman's equation was used if a complete observed meteorological data were available, and Jensen-Haise's equation was used if a forecasted meteorological data were available, However none of the observed or forecasted data were available, the equation (15) was used. b. As an input time data, a crop carlender was used, which was made based on the time when the growth stage of the crop shows it's maximum effective leaf coverage. 9. For the purpose of validation of the models, observed data of soil moiture content under various conditions from May, 1975 to July, 1975 were compared to the data predicted by Model-I and Model-II. Model-I shows the relative error of 4.6 to 14.3 percent which is an acceptable range of error in view of engineering purpose. Model-II shows 3 to 16.7 percent of relative error which is a little larger than the one from the Model-I. 10. Comparing two models, the followings are concluded: Model-I established on the theoretical background can predict with a satisfiable reliability far practical use provided that forecasted meteorological data are available. On the other hand, Model-II was superior to Model-I in it's simplicity, but it needs long period and wide scope of observed data to predict acceptable soil moisture content. Further studies are needed on the Model-II to make it acceptable in practical use.

  • PDF

광화유체의 비등과 희석에 의한 통영 천열수계 Au-Ag-Te 장화작용에 대한 반응경로 모델링 (Au-Ag-Te Mineralization by Boiling and Dilution of Meteoric Ground-water in the Tongyeong Epithermal sold System, Korea: Implications from Reaction Path Modeling)

  • Maeng-Eon Park;Kyu-Youl Sung
    • 자원환경지질
    • /
    • 제34권6호
    • /
    • pp.507-522
    • /
    • 2001
  • 통영광산은 첨열수광상으로서 능망간석 , 백운모, 일라이트, 황철석 , 방연석 , 황동석 , 섬아연석 , 아칸다이트 및 헤사이트등의 광물을 수반하는 초기의 광석광물 침전시기와 후기의 맥석광물 침전시기로 구분된다. 초기는 반복적인 대상구조를 띠고, 황화광물이 침전된 시기로서 텔루리움 광물과 함께 엘렉트럼이 산출된다. 후기에는 주로 단산염 광물과 천금속광물이 침전되었다. 통영 열수계에서 광화단계에 따른 상이한 열수유체의 변천과정을 구체적으로 규명하기 위하여 프로그램 CHILLER를 이용한 수치모델링이 실시되었다. 반응경로 모델링은 28$0^{\circ}C$에서 모암인 안산암과의 반응을 비롯하여, 27$0^{\circ}C$에서 12$0^{\circ}C$까지의 단순한 등압 냉각, 비등과 지하수의 혼입에 따른 희석 및 압력파 온도가 감소되는 조건에서 수행하였다. 모델링 결과 초기 광화유체는 산성용액(pH=5.7)으로 상대적으로 높은 염농도와 금속원소 함량이 높다. 장화유체 내의 금의 함량은 열수계의 천금속원소 총량과 황화물의 활동도에 의해 지배된다. 통영 천열수계에서의 광화작용은 천부에서 일어난 참화유체의 비등과 이에 수반된 가열된 지하수의 흔입에 의한 반응경로를 반영하며, 현미경에서 관찰된 광물공생 특성과 모델링에 의한 침전광물의 조합 및 엘렉트럼의 화학조성 등에서 동일한 경향을 나타낸다. 이러한 유사성은 Te 함유하는 천열수 금 . 은광상이 열수계에서의 비등과 유체혼합(희석)에 의해 생성되었음을 지시한다. 반응경로 모델링 연구는 광상성인을 이해하는 중요한 수단이며, 유사한 지질환경에서의 광강탐사에 유용한 자료로 활용될 것으로 생각된다.

  • PDF

상온유통을 위한 가열살균 중의 통 초당옥수수의 품질변화 연구 (Characterization of quality changes of whole super sweet corn (Zea mays saccharata Sturt.) during thermal sterilization for shelf-stable products)

  • 이윤주;윤원병
    • Journal of Applied Biological Chemistry
    • /
    • 제62권1호
    • /
    • pp.25-30
    • /
    • 2019
  • 본 연구에서는 상온 저장이 가능하며 별도의 처리 없이 바로 섭취할 수 있는 통초당옥수수를 위한 최적 살균법을 도출하고 저장기간동안 최적 살균된 초당옥수수의 품질인자를 분석하였다. 살균 시 유통기한 확보 및 초당옥수수의 고유한 특징인 아삭한 식감이 가열처리에 의하여 감소되는 것을 최소화 하기 위해 비가열 전처리 공정으로서 알코올 세척을 도입하였으며, 냉점은 초당옥수수의 속대와 중심 사이로 하였다. 초당옥수수의 표면은 알코올 세척을 통하여 1 log CFU/g 이상을 감소시킨 후 $F_{121.1}=4$분을를 만족하도록 가열하여 $25^{\circ}C$ 인큐베이터에서 9개월간 저장하면서 대조군으로서 일반적인 증숙의 방법으로 가열한 초당옥수수의 품질과 비교하였다. 알코올 처리 및 가열 살균한 초당 옥수수의 조직감은 대조군의 조직감 대비 30%이내를 유지하여 최소 $464.50{\pm}103.35g$에서 최대 $514.50{\pm}81.83g$값을 나타내었으며, 당도는 샘플 간의 차이가 다소 있었으나 최소 $28.83{\pm}1.05%$에서 최대 $34.36{\pm}0.42%$값으로 대조군에 대비하여 30% 이내 당도를 유지하였다. 초당 옥수수 겉표면 황색도는 대조군 대비 5% 이상 향상되어 최대 $34.36{\pm}0.42$값을 나타내었으며, 미생물 검사에서는 일반세균과 진균류가 저장 9개월 동안 검출되지 않았다. 이러한 연구결과는 가열살균한 초당옥수수의 품질변화가 최소화되면서 6개월 이상의 상온유통이 가능한 최적 살균 방법을 도출하였으며, 이에 따라 가열에 의하여 식품 본연의 조직감 감소를 최소화하면서 상온유통이 가능한 살균제품에 이용될 수 있다.

붕소-중성자 포획치료를 위한 미세 속중성자 선량 특성 연구 (Dosimetry of the Low Fluence Fast Neutron Beams for Boron Neutron Capture Therapy)

  • 이동한;지영훈;이동훈;박현주;이석;이경후;서소희;김미숙;조철구;류성렬;유형준;곽호신;이창훈
    • Radiation Oncology Journal
    • /
    • 제19권1호
    • /
    • pp.66-73
    • /
    • 2001
  • 목적 : 붕소-중성자 포획치료법(Boron Neutron Capture Therapy, BNCT)을 위해 원자력병원 싸이클로트론에서 발생되는 최대에너지 34.4 MeV의 속중성자(Fast neutron)를 70 cm 파라핀으로 감속시킨 후 선량 특성을 조사하였다. 그 결과를 토대로 열외중성자(Epithermal neutron) 선량 측정법에 대한 프로토콜을 확립하여 원자로에서 방출되는 열외 중성자 선량 특성 평가의 기초를 삼고, 가속기를 이용한 BNCT 연구에 대한 타당성 여부를 조사하고자 한다. 대상 및 방법 : 공기 중 선량 및 물질 내 선량 분포 측정을 위해 Unidos 10005 (PTW, Germany) 전기계와 조직 등가 물질인 A-150 플라스틱으로 제작된 IC-17 (Far West, USA) 및 IC-18, ElC-1 이온함을 사용하였고, 감마선의 측정을 위해서는 마그네슘으로 제작된 IC-l7M 이온함을 이용하였으며 조직등가 기체와 아르곤 기체를 분당 5cc 씩 주입하며 측정하였다. 중성자, 광자, 전자가 혼합된 장의 모의 수송 해석을 위해 이용되는 Monte Carlo N-Particle (MCNP) transport code를 사용하여 2차원적 선량 분포 및 에너지 분포를 계산하였으며 이 결과를 측정값과 비교하였다. 결과 : BNCT에서의 유효 치료 깊이인 물 팬텀 4 cm에서의 선량은 치료기 1 MU 당 $6.47\times10^{-3}\;cGy$로 미세하였으며, 이때 감마 오염도(contamination)는 $65.2{\pm}0.9\%$로 중성자보다는 감마선에 의한 선량 기여분이 우세하였다. 깊이에 따른 선량 분포 특성에서는 중성자 선량은 선형적으로 감쇠 되었고, 감마선량은 지수적으로 보다 급격히 감쇠되는 경향을 보였으며 전체 선량의 $D_{20}/D_{10}$은 0.718 이었다. MCNP에 의한 에너지 분포 전산 계산의 결과 2.87 MeV 이하에서 중성자 피크가 나타났으며, 저에너지 영역에서는 감마선이 연속적으로 분포되는 양상을 보였다. 결론 : 벽 물질이 서로 다른 두 개의 이온함을 사용한 직접 선량 측정과 MCNP 전산 시뮬레이션을 이용한 공간 선량분포 계산으로 미세 속중성자 빔에 대한 선량 특성을 파악할 수 있었으며, 원자로 열외중성자 주(Epithermal neutron column)에 대한 선량 평가 자료로 확보하였다. 아울러 가속기에 대한 연구가 진행되어 고전압, 고전류를 발생시키는 전원 공급장치와 표적핵(Target) 물질이 개발되고 비스무스나 납 등에 의해 감마 오염도를 줄일 경우, 싸이크로트론에 의한 보론-중성자 포획치료도 가능해질 것으로 판단된다.

  • PDF