• 한국가스학회지
• /
• 제20권2호
• /
• pp.10-15
• /
• 2016

이 논문의 목적은 자동차 에어컨 가스 누설에 관련된 고장사례를 분석하고 고찰한 것이다. 첫 번째 사례는 냉매가 누설된 상태에서 에어컨 컴프레서가 계속 작동되었다. 이로 인해 에어컨 컴프레서 내부의 피스톤이 윤활부족으로 인해 피스톤이 부분적으로 에어컨 컴프레서 내부의 실린더에 소착되는 현상이 발생하였다. 이것이 엔진작동 중 부하를 증대시켜 엔진의 회전수 변동과 함께 엔진의 작동이 정지되는 현상이 발생된 것으로 확인되었다. 두 번째 사례는 에어컨 라인과 관련 시스템을 확인한 결과 에어컨 컴프레서에서 뒤쪽으로 가는 컨덴서 고압파이프에서 미세한 균열에 의해 에어컨 냉매 가스가 누설되는 것을 확인하였다. 세 번째 사례는 에어컨 컨덴서 핀 부에서 육안으로 확인하기 어려운 미세한 크랙에 의해 컨덴서 내부 안쪽에서 에어컨 가스가 미세하게 누설되는 것을 확인하였다. 따라서, 에어컨 시스템은 에어컨 냉매가스에 의해 자동차의 실내의 온도를 낮춰 공기조화를 하는 시스템이므로 최적의 상태를 유지할 수 있도록 철저한 관리를 하도록 하여야 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.67-74
• /
• 2000

Recently, PTFE-polymide composites are being used self-lubricating parts for industrial field. Thus, this study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polymide composites. The friction and wear test was carried out for the different composition ratio under the atomsphere room temperature and constant load of 7.69N and their friction and wear properties were compared with each other at various sliding speed. notable results are summarized as follows. PTFE 100% showed that friction coefficient was almost same values at 0.94 and 1.88m/s but the value was decreased at 2.83m/s because the friction temperature is higher than low speed. PTFE 80%-PI 20% showed the lowest mean friction coefficient at 2.83m/s. PTFE 20-PI 80% showed the highest friction coefficient at 0.94m/s and the value was decreased at high speed but the value is higher than other materials except PTFE 100 %. PI 100% showed the highest friction coefficient at 0.94 and 1.88m/s becuase adhesive wear mainly occurred that speed. PTFE 100% showed highest specific wear rate on the whole. Specific wear rate of PTFE 80%-PI 20% was almost the same value with PTFE 20%-PI80%. PI 100%showed the lowest value at high sliding speed because the friction surface was thicken and carbonated by high friction temperature.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.967-971
• /
• 2004

Today, as the demands for home appliances are increasing, the understanding of noise and vibration characteristics have become more important. It is hard to control its vibration and noise characteristics, because its mechanical structure is very complex. In this study a model of reciprocating compressor is developed. Spring, frame, and LDT are modeled as flexible body, and the other parts are modeled as rigid. FEM model of frame is simplified in order to save the simulation time. We validated the simple model by comparing their natural frequencies and mode shapes. Motor torque is applied to a rotor, and the piston is subjected to a gas pressure. The vibrational characteristics of compressor is analyzed with LS-DYNA. Its results are compared with the simulation results of rigid body frame. The effect of LDT is also studied by comparing the vibration of frame with the results of simulation with no LDT.

• 설비공학논문집
• /
• 제29권11호
• /
• pp.570-579
• /
• 2017

In this study, we examined the multi-stage piston-type air compressors typically used in a railroad vehicle, and the heat transfer efficiency was analyzed according to the design conditions of the heat exchanger (a compressor component module for cooling the compressed high temperature air). For the fin-tube heat exchanger used in the most air compressors, numerical analysis was performed to analyze heat transfer by defining the various rectangle tube sizes and the number of fin-per-unit area as design variables under the same flow rate of compressed air. Also, this analysis compared the temperature of the compressed air. Regarding environmental conditions for analysis, the flow rate of the external cooling air was measured and the mean value of the values was applied. And a "turbulence model" was considered in both the external flow of the cooling air and the internal flow inside the tube. From the results of analysis, it was found that the change of the aspect ratio value of the tube greatly influences the heat transfer efficiency of the compressed air, and influences if the fin density is relatively small. As a result, the optimum design specifications of the heat exchanger for air compressors were confirmed based on the analysis of the heat transfer efficiency, according to the design conditions of fin and tube by the operating temperature range of the compressed air.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1991년도 제13회 학술강연회초록집
• /
• pp.55-59
• /
• 1991

실중적으로 하중을 받는 선접촉부의 윤활명성은 johnson chart, 또는 Hooke의 Chart에서 나타난바와 같이 강체$\cdot$점도일정명감 (Rigid-Isovicosity region), 점도변화 명성 (Elasticity-Variable Viscosity Region), 탄성체$\cdot$점도일정명성 (Elasticity-Isoviscosity Region)으로 분산 되어지는데 명성내에서 2차원 선접촉의 경우 탄성 파라메터 ge가 적고 점성 파라미터 gv가 큰 Tribology적인 실제 문제가 많은데 비하여 이 점성에서의 윤활특성에 관한 수치적인 Simulation이나 실험적인 보고가 거의 없는 실정이다. 예를들면 engine의 Piston Ring과 Cylinder 간의 윤활, Vane 식의 유압펌프등에서 볼수 있는 습동부의 윤활, Rotary Engine의 Rotor 선단부분, Rotary Compressor의 Rotor와 stator간의 상대운동 점성에서 나타나는 Tribology적인 점성은 대부분이 강체$\cdot$점도 변화점성이거나 그에 바로 인접한 탄생체$\cdot$점도 변화의 초기 점성에 분포하고 있다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.63-66
• /
• 2002

A free piston and free displacer (FPFD) Stilting cryocooler for the cooling infrared and cryo-sensor is currently under development at Korea Institute of Machinery & Materials. In this study, the dynamic characteristics of the displacer in the expansion space of the Stirling cooler was investigated by experiment. The experimental results show that the Stirling cryocooler has maximum cooling capacity at the certain relation between operating frequency and natural frequency of the displacer and the operating frequency of the Stirling crycooler should be determined by natural frequency of the linear compressor and displacer.

• 한국유체기계학회 논문집
• /
• 제3권2호
• /
• pp.44-49
• /
• 2000

Small sonic nozzles (throat diameter $0.28{\~}4.48mm$) were tested in the gas flow standard system. This standard system is composed of two bell provers and 5 column piston provers, compressor, filters, and dehumidifier. The discharge coefficients of small some nozzles are obtained and correlated as a function of throat Reynolds numbers with $0.316\%$ uncertainty at a confidence level $95\%$. The tested high Reynolds number was the lower limit of ISO 9300 specifications. The data are useful as data base for revision of ISO 9300.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.18-23
• /
• 2012

HI-WORTH T-32, a non-powered plasma cutter, is a portable cutter that utilizes compressor-plasma inverter. With a special air-pressure piston, the cutter is semiautomatic. When they were produced by die casting dies, the bodies or housings of the cutter have defects about 100 percent of defect rate due to blisters and thermal deformation. Therefore, they are produced by mechanical machining, which leads to a hike in material and machining costs and to the loss of productivity. And companies are left with insignificant profit margins. Besides mechanical machining, this study proposes to modify defective mold and cut down defective rate and boost productivity.

• 한국정보통신학회논문지
• /
• 제5권6호
• /
• pp.1122-1127
• /
• 2001

본 논문에서는 공기압축기 구동용 유도전동기를 대상으로 부하토크관측기와 신경망을 이용 한 피드포워드 보상기를 결합한 속도 적응제어시스템을 제안한다. 공기압축기를 구동하는 전동기는 피스톤 의 상하운동에 의해 급격한 가변형의 부하를 받게 되고, 이로 인해 운전특성에 문제가 발생된다. 신경망 추정기를 이용하여 속도 제어기의 이득을 실시간으로 동조함으로써 전동기의 속도제어 특성을 개선한다. 제안된 시스템에 대한 이론적 해석과 시뮬레이션을 통해 그 타당성을 검정한다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2001년도 추계종합학술대회
• /
• pp.397-400
• /
• 2001

본 논문에서는 공기압축기 구동용 유도전동기를 대상으로 부하토크관측기와 신경망을 이용한 피드포워드 보상기를 결합한 속도 적응제어시스템을 제안한다. 공기압축기를 구동하는 전동기는 피스톤의 상하운동에 의해 급격한 가변형의 부하를 받게 되고, 이로 인해 운전특성에 문제가 발생된다. 신경망 추정기를 이용하여 속도 제어기의 이득을 실시간으로 동조함으로써 전동기의 속도제어 특성을 개선한다. 제안된 시스템에 대한 이론적 해석과 시뮬레이션을 통해 그 타당성을 검정한다.