• 한국구조물진단유지관리공학회 논문집
• /
• 제23권3호
• /
• pp.43-50
• /
• 2019

본 연구는 강섬유의 인장강도 및 형상비가 고강도 및 보통강도 강섬유보강 콘크리트(Steel fiber-reinforced concrete, SFRC)의 압축 및 휨 거동에 미치는 영향을 평가하기 위하여 실시되었다. 또한 본 연구에서는 가력속도에 따른 SFRC의 압축거동을 평가하였다. 이를 위해 총 4종류의 강섬유가 설계기준 압축강도 35 및 60 MPa급 SFRC에 각각 사용되었다. 압축거동 평가를 위해 지름 150 mm 및 높이 300 mm의 원주형 공시체를 사용하였으며, 단면 $150{\times}150mm$ 및 지간 450 mm의 각주형 공시체를 사용하여 휨 거동 평가를 실시하였다. 실험결과 강섬유의 혼입은 콘크리트의 인성을 크게 향상시키는 것으로 나타났으며, 고강도 강섬유의 사용은 고강도 SFRC의 성능개선에 효과적인 것으로 나타났다. 아울러 본 연구에서는 SFRC의 휨 인성지수에 근거한 압축인성지수 산정기법을 제안하였다.

• 한국건설순환자원학회논문집
• /
• 제11권1호
• /
• pp.39-47
• /
• 2023

최근 구조물의 장대화로 인하여 고강도 재료의 경량화 요구가 빈번해지고 있는 실정이다. 하지만 현재까지는 압축강도 120 MPa, 단위중량 20 kN/m³ 정도의 고강도 경량 콘크리트를 구조부재에 적용하기 위한 콘크리트와 철근의 부착 특성에 관한 연구가 부족한 실정이다. 따라서 본 논문에서는 압축강도 120 MPa, 단위중량 20 kN/m³ 정도의 고강도 경량 콘크리트 108개의 시편을 제작하여 직접 인발 부착실험을 수행하였고, 실험결과와 현행 설계기준과 비교하여 부착특성을 평가하였다. 솔리드버블은 단위중량 감소에 비해서 압축강도 및 탄성계수 감소효과는 상대적으로 적게 나타나, 초경량화를 위해서는 반드시 적용되어야 할 재료로 판단되며, ACI-408R의 부착강도 산정식과 실험결과는 비교적 유사한 것으로 판단되며, 더 낮은 압축강도, 단위중량의 콘크리트보다 더 큰 슬립 및 매개변수 값을 가지는 것으로 나타났다.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.137-163
• /
• 1990

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the Properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of the consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfate and the magnesium sulfate promoted the hardening and the aluminium phosphate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect of the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate and cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.139-165
• /
• 1991

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfata and the magnesium sulfate promoted the hardening and the aluminium phoshpate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect fo the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near $250^{\circ}C$ and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate ad cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• Advances in concrete construction
• /
• 제13권3호
• /
• pp.215-221
• /
• 2022

Considering their similar mass densities, an attempt was made to optimize the mix design of micro-concrete that used barite sand as an aggregate by substituting marble powder (5%, 10%, 20%, 30%, 40%, 50%, 70%), clay brick powder (30%, 50%, 70%), and fly ash (30%, 50%, 70%) for the concrete (by mass) to form specimens for shaking table tests. The test results showed that for these three groups of materials, the substitutions had little effect on the density. The barite sand played a decisive role in the density, and the overall density of the specimens reached approximately 2.9 g/cm³. The compressive strength and elastic modulus decreased with an increase in the substitution rates for the three types of materials. Among them, the 28 day compressive strength values of the 40% and 50% marble powder groups were 11.73 MPa and 8.33 MPa, respectively, which were 58.7% and 70.7% lower than the control group, respectively. Their elastic modulus values were 1.33×10⁴ MPa and 1.42×10⁴ MPa, respectively, which were 39.1% and 35% lower than those of the control group, respectively. The 28 day compressive strength values of the 50% and 70% clay brick powder groups were 13.13 MPa and 5.8 MPa, respectively, which were 53.8% and 79.6% lower than the control group, respectively. Their elastic modulus values were 1.54×10⁴ MPa and 1.19×10⁴ MPa, respectively, which were 29.7% and 45.4% lower than those of the control group, respectively. The 28 day compressive strength values of the 50% and 70% fly ash groups were 13.5 MPa and 7.1 MPa, respectively, which were 52.5% and 75% lower than those of the control group, respectively. Their elastic modulus values were 1.36×10⁴ MPa and 0.95×10⁴ MPa, respectively, which were 37.9% and 56.6% lower than those of the control group, respectively. There was a linear relationship between the 28 day compressive strength and elastic modulus, with the correlation coefficient reaching a value higher than 0.88. The test results showed that the model materials met the high density, low compressive strength, and low elastic modulus requirements for shaking table tests, and the test data of the three groups of different alternative materials were compared and analyzed to provide references and assistance for relevant model testers.

• 대한토목학회논문집
• /
• 제29권6C호
• /
• pp.321-329
• /
• 2009

국내 암석의 일축응력상태와 삼축응력상태의 한계변형률 특성을 연구하고자 국내에 분포하는 6종류의 암석을 대상으로 실내 일축 및 삼축압축시험을 실시하였다. 일축압축실험에 의한 일축압축강도는 대부분 1~100MPa의 범위이었고, 한계변형률도 0.1~1.0%에 위치하여 전반적으로 Sakurai(1982)가 제시한 상 하부 경계선 내에 분포하였다. 그리고 암석의 파괴/한계변형률의 비(${\varepsilon}_f/{\varepsilon}_0$)는 일축강도에 따라 1.0~1.8의 범위로 모두 1.0 이상 나타났다. 삼축압축실험에 의한 한계변형률은 모든 암석에서 0.8%이하로 일축압축실험에서의 최대 한계변형률 1.0% 보다 작은 값을 보였으며, 일축 및 삼축압축실험로부터 산정된 값은 거의 대부분의 암석시료에서 1.0~8.0정도의 범위였다. 본 연구를 통하여 삼축응력상태인 암반의 파괴변형률(${\varepsilon}_{f3}$)은 일축응력상태의 파괴변형률(${\varepsilon}_{f1}$)에 비하여 1.0~8.0배 정도 크고, ${\varepsilon}_{f1}$은 일축응력상태의 한계변형률(${\varepsilon}_{01}$)보다 1.0~1.8배정도 크게 나타나 암반터널 변위계측에 의한 안정성 기준치를 일축강도에 따른 한계변형률(${\varepsilon}_{01}$)로 규정하는 것은 안정측 관리기준이 되는 것으로 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.239-242
• /
• 2002

This study is intended to investigate the relationship between rebound value of P type schmidt hammer and the compressive strength with various aggregates, and a series of experiments about early strength quality control by P type schmidt hammer was performed. According to the results, the compressive strength of concrete using basalt and limestone aggregate is higher by 3% and lower by 4% than that of concrete using granite aggregate respectively. Concrete using basalt and lime stone aggregate show high rebound value in vertical strike. Estimation of the compressive strength does not show differences in horizontal strike, but the compressive strength is estimated high in order of granite, basalt and limestone aggregate in vertical strike. A good correlation between the rebound value of schmidt hammer and the compressive strength is confirmed regardless of aggregate types, so it could be possible to control the quality of concrete by P type schmidt hammer test when basalt and limestone aggregates are used at the same time.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.139-140
• /
• 2015

The purpose of this study was to evaluate existing compressive strength equation with concrete exposed to high temperature by ultrasonic pulse velocity. As the result, original compressive strength equation is proper only for compressive strength of normal concrete. Therefore, an accumulation of experimental database of concrete exposed to high temperature is necessary for proposal of new compressive strength equation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.653-658
• /
• 2001

The purpose of this study is to evaluate the compressive strength properties of hardening using the unrefined fly-ash and waste lime and to offer basic data to someone for recycling waste lime Waste limes are tested that specific gravity and pH value and observed microstructure of particle with SEM. The compressive strengths of Wast lime hardening which is mixed with regular ratio according to each admixture are measured. In the results of test, The pH of wast lime is very high by pH 12.1 and specific gravity is 2.22. Compressive strengths on hardening modified waste lime and fly ash is very effective. The vest compressive strengths is show that CaCl$_2$ existed in waste lime

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.148-153
• /
• 2004

It is well-known that the mechanical behavior of fiber-reinforced composites under hydrostatic pressure environment is different from that of atmospheric pressure environment. It is also known that the mechanical behavior of fiber-reinforced composites is affected by a strain rate. In this work, we investigated the effect of strain rate on the compressive elastic modulus, fracture stress, and fracture strain of carbon/epoxy composites under hydrostatic pressure environment. The material used in the compressive test was unidirectional carbon/epoxy composites and the hydrostatic pressures applied was 270㎫. Compressive tests were performed applying three strain rates of 0.05％/sec, 0.25％/sec, and 0.55％/sec. The results showed that the elastic modulus increased with increasing strain rate while the fracture stress was little affected by the strain rate. The results also showed that the fracture strain decreased with increasing strain rate.