• 콘크리트학회논문집
• /
• 제20권5호
• /
• pp.583-592
• /
• 2008

최근 고강도콘크리트의 압축강도, 탄성계수 및 최대하중에서의 변형에 대한 고온의 영향이 실험적으로 연구되어지고 있다. 본 연구는 40, 60, 80 MPa 급 고강도콘크리트의 재료 역학적 특성에 있어서 $20{\sim}700^{\circ}C$ 범위로 상승되는 온도의 영향을 연구하는데 그 목적이 있다. 본 연구에서는 설계하중 사전재하 및 잔존강도시험 방법으로서 시험체를 가열하기 전에 상온 압축강도의 25% 하중을 사전재하한 후 가열을 실시하고, 가열하는 동안 하중을 유지하며, 목표온도에 도달한 후 고온상태 및 상온에서 24시간 냉각상태에서 시험체가 파괴될 때까지 재하를 실시하였다. 시험은 W/B 46%, 32% 및 25%로 이루어진 콘크리트 시험체에 대하여 $20{\sim}700^{\circ}C$의 다양한 온도하에서 실시하였다. 시험 결과 콘크리트 강도가 증가할수록 고온에서의 상대적인 압축강도와 탄성계수는 감소하였으며, 최대하중에서의 축방향 변형은 설계하중 사전재하와 상관성이 높은 것으로 나타났다. 또한 온도상승에 따른 콘크리트의 열팽창 변형은 압축강도 뿐만 아니라 하중 크기의 영향을 받는 것으로 나타났으며, 최종적으로 가열을 받은 고강도콘크리트의 압축강도 및 탄성계수에 대한 모델식을 제안하였다.

• 한국농공학회지
• /
• 제16권3호
• /
• pp.3472-3476
• /
• 1974

This test was attempted to investigate the effects of some mix designs of concreteon the compressive strengths and corrosive rates when exposed to sea water of the West Sea. In this test, concrete mixes consisted of an ordinary concrete, a pozzolan concrete and concretes with different admixtures such as fly ash, pozzolith and vinsol resin. Compressive strengths of the concrete were measured at ages of 1-year and 2-years when exposed to both sea water and fresh water. Corrosive rate was tested at ages of 1-year and 2-years when exposed to sea water only. The results obtained from the test may be summarized as follows: (1) When all of concretes were exposed to fresh water, compressive strength of an ordinary concrete was the lowest at all mixes of concretes, and all of them showed higher strength as the exposing age is longer. It was evidance that the uses of pozsolan cement, fly ash, pozzolith and vinsol resin in mix design of concrete had an effect on increasing compressive strength and that fresh water also had an effect on curing concretes even though at a long-time age. (2) When concretes were exposed sea water, a concrete with fly ash was the highest in compressive strength and its strength was increasing as the exposing age is longer, but the other concretes were decreased at 2-year exposure. It was found that a concrete with fly ash was the most effective on compressive strength of all concrete, but the other concretes were attacked by action of the sea water. (3) The use of vinsol resin admixture was the most resistant to corrosion by sea water, while the use of pozzolith was the most serious at corrosion and the others were corroded to almost same extent. (4) The relationship between corrosions and compressive strengths of concretes was not clearly correlated yet. It was known that the corrosive rate of concretes could not affect to compressive strengths by 2-year exposure of the sea water. (5) Pozzolan concrete was the most effective in compressive strength when exposed to fresh water only, However, the use of a fly ash admixture was available for compressive strength when exposing to both fresh water and sea water. It was also noticed that the use of vinsol resin was not available for strengths of concrete but for resistance to corrosion when exposed to sea water. (6) It was found that the use of pozzolith was so defective in compressive strengths and corrosiive resistance when exposing to sea water that it was only available for fresh water.

• KCI Concrete Journal
• /
• 제14권1호
• /
• pp.43-50
• /
• 2002

In this study, size effect tests were conducted on axial compressive strength of concrete members. An experiment of Mode I failure, which is one of two representative compressive failure modes, was carried out by using dimensionally proportional cylindrical specimens (CS). An adequate notch length was taken from the experimental results obtained from the compressive strength experiment of various initial notch lengths. Utilizing the notch length, specimen sizes were then varied. In addition, new parameters for the modified size effect law (MSEL) were suggested using Levenberg-Marquardt's least square method (LSM). The test results show that size effect was apparent for axial compressive strength of cracked specimens. Namely, the effect of initial notch length on axial compressive strength size effect was apparent.

• Steel and Composite Structures
• /
• 제9권6호
• /
• pp.519-534
• /
• 2009

This study intends to examine the characteristics of compressive behavior and conducts comparative analysis between normal compressive strength under existing equations (LRFD, ACI 318, EC 4) and experimental the maximum compressive strength from the compression experiment for the unstiffened steel plate-concrete structures. The six specimens were made to evaluate the constraining factor (${\xi}$) and width ratio (${\beta}$) effects subjected to the compressive monotonic loading. Based on this experiments, the following conclusions could be made: first, compressive behaviors of the specimens from the finite element analysis closely agreed with the ones from the actual experiments; second, the higher the width ratio (${\beta}$) was, the lower the ductility index (DI) was; and third, the test results showed the maximum compressive strength with a margin by 7% compared to the existing codes.

• 콘크리트학회논문집
• /
• 제12권6호
• /
• pp.99-108
• /
• 2000

The size effect on axial compressive strength in notched concrete specimens was experimentally investigated. Based on the concept of the fracture mechanics and size effect law, theoretical studies for axial compressive failure of concrete were reviewed, and two failure modes of concrete specimens under compression were discussed. In this study, experiments of axial compressive failure, which is one of the two failure modes, was carried out by using cylindrical specimens. Adequate notch length was taken from the experimental result of strength variation based on the notch length. And, by taking various sizes of specimens the size effect on axial compressive strength of concrete was investigated. Also, model equations were suggested by modified size effect law (MSEL). The test results show that size effect appears conspicuously for all series of specimens. Additionally, the effect of initial notch length on axial compressive strength was also apparent.

• 콘크리트학회논문집
• /
• 제17권3호
• /
• pp.313-322
• /
• 2005

최근 들어 리모델링시장이 점차 신축시장의 대체시장으로 부각되고, 재건축아파트에 대한 안전진단의 문제가 사회의 주요 관심사가 되면서 기존 콘크리트 구조체의 상태에 대해 체계적이고 과학적인 구조물 진단 및 평가가 요구되고 있으며, 비파괴 시험방법에 의한 콘크리트 압축강도를 추정하기 위한 데이터의 신뢰성에 대한 중요성이 점점 증대되고 있다. 본 연구에서는 선 타격 개념의 반발도 시험기를 적용하여 콘크리트 압축강도 추정의 신뢰성을 향상시키는 방안을 모색하고, 재령 및 타격각도에 따라 선 타격 반발도 시험기에 적용할 수 있는 압축강도 추정식을 제안하고자 하였다. 연구 결과, 선 타격 반발도 시험기는 재령별, 타격각도별로 별도의 추정식을 제안하는 것이 콘크리트 압축강도 추정의 신뢰성을 향상시키는데 긍정적인 것으로 나타났으며, 압축강도와 반발도 사이의 상관관계는 초기 및 중기재령, 그리고 타격각도별로 초기재령 $-45^{\circ}$를 제외한 모든 부분에서 선 타격 반발도 시험기 25mm가 가장 높은 것으로 나타나 기존의 슈미트해머에 비해 콘크리트 압축강도 추정의 신뢰성을 높일 수 있는 방안이 될 것으로 분석되었다.

• Geomechanics and Engineering
• /
• 제19권4호
• /
• pp.353-360
• /
• 2019

The elastic modulus is an important parameter to characterize the property of rock. It is common knowledge that the strengths of rocks are significantly different under tension and compression. However, little attention has been paid to the bi-modularity of rock. To validate whether the rock elastic moduli in tension and compression are the same, Brazilian disc, direct tension and compression tests were conducted. A horizontal laser displacement meter and a pair of vertical and transverse strain gauges were applied. Four types of materials were tested, including three types of rock materials and one type of steel material. A comprehensive comparison of the elastic moduli based on different experimental results was presented, and a tension-compression anisotropy model was proposed to explain the experimental results. The results from this study indicate that the rock elastic modulus is different under tension and compression. The ratio of the rock elastic moduli under compression and tension ranges from 2 to 4. The rock tensile moduli from the strain data and displacement data are approximate. The elastic moduli from the Brazilian disc test are consistent with those from the uniaxial tension and compression tests. The Brazilian disc test is a convenient method for estimating the tensile and compressive moduli of rock materials.

• 한국환경복원기술학회지
• /
• 제5권6호
• /
• pp.9-13
• /
• 2002

This study has been performed to investigate the physical and mechanical characteristics of compaction, volume change and compressive strength for reinforced soil mixed with cement. And confirm the reinforcing effects with admixture such as cement. To this end, a series of compaction test and compression test was conducted for clayey soil(CL) and cement reinforced soil. In order to determine proper moisture content and mixing ratio, pilot test was carried out for soil and cement reinforced soil. And the mixing ratio of cement admixture was fixed 3%, 6%, 9% and 12% by the weight of dry soil. As the experimental results, the maximum dry unit weight(${\gamma}_{dmax}$) was increased with the mixing ratio and then shown the peak at 10% reinforced soil, but the optimum moisture content(OMC) and the volume change was decreased with the ratio increase. And the compressive strength volume change was decreased with mixing ratio increased.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.3-9
• /
• 2002

Paper sludge ash was assured as material of a sort of pozzolan. For the reason of fluidity decrease caused by the strong absorption of paper stooge ash and the decrease of compressive strength in case of using over30% replacement by the weight of cement, paper sludge ash is not suitable for blending material. Therefore, it is necessary to find proper replacement ratios between paper sludge and blast furnace slag to insure compressive compensation and appropriate slump. Accordingly, as varied the blending ratios of paper sludge and blast furnace slag, testing mortar was made. This study was aimed to investigate the possibility of using blending replacement of paper sludge ash and blast furnace slag throughout compressive test, flow test, SEM(Scanning Eletron Microscope), MIP(Mercury Intrusion Porosity test), and TG-DTA(Thermal analysis).

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.198-203
• /
• 1995

The objective of this study is to provide the information on the techniques of manufacturing and experiment in small scale modeling of precast concrete(P.C.)large panel structures. The adopted scale was 1/5th 4types of experiments were performed : material tests for model concrete and model reinforcement, compressive test of horizontal joint, shear test of vertical joint and cyclic static test of 2-story subassemblage structure. Based on the experimental results, the following conclusions are drawn: (1)Model concrete may have in general larger compressive strength than expected. (2) Model reinforcement can show less ductility if the annealing processes were performed without using vaccuum tube. (3) Failure modes of horizontal and vertical joints were almost same for both prototype and model. But the strength of model appears to be higher than required by similitude law. (4)Hysteretic behavior of 1/5 scale subassemblage model can be made quite similar to prototype's if the ductility of model reinforcement and compressive strength of model concrete could be representative of those of prototype.