• 한국구조물진단유지관리공학회 논문집
• /
• 제10권1호
• /
• pp.190-196
• /
• 2006

기존 연구에서 살펴보면, 철근콘크리트구조물에 발생한 화재로 인해 경화된 시멘트 페이스트와 골재의 수축과 팽창의 차이에 따라 조직이 와해되고, 열응력에 의해 균열이 발생하여 내구성이 저하한다. 그래서 성능저하의 정확한 진단은 일반적인 콘크리트구조물에서 방화성능저하의 매커니즘에 관한 기초가 요구되며, 고온에 노출된 콘크리트의 특성에 대한 기초 정보와 데이터는 성능저하의 정확한 진단을 위해 필요하다. 따라서, 본 연구는 다양한 콘크리트 시험체를 제작하여, 고온 환경에서 노출시켜, 폭열을 관찰하고, 공학적인 특성을 평가함으로서 화재피해를 입은 콘크리트구조물 성능저하의 빠르고 정확한 진단을 위한 기초적인 데이터를 제공하고자 한다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 봄 학술발표회 논문집
• /
• pp.479-486
• /
• 2004

The purpose of this study is to practical use with increase safety, usablility and economical. In this study, the property of fatigue behavior was tested by comparing reinforced concrete and steel fiber reinforced concrete. The basic test, the static test and fatigue test were used as the research methods. Basic on the test, the material compressive strength test and split tensile strength test ware conducted 7 days and 28 days after the concrete was poured. In the static test, there ware four types of experimental variables of the steel fiber mixing ratio : 0.00%, 0.75%, 1.00%, and 1.25%. The ultimate load initial diagonal tension crack, and initial load of flexural cracking were all observed by static test. A methodology for the probabilistic assement of steel fiber reinforced concrete(SFRC) which takes into account material variability, confinement model uncertainty and the uncertainty in local and globa failure criteria is applied for the derivation of vulnerability curves for the serviceability and ultimate limit states, the reliability of SFRC using the proposed practical linear limit state model is evaluated by using the AFOSM(Advanced First Order Second Moment) method and MCS(monte-Calrosimulation) method.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.270-270
• /
• 2016

We fabricated an organic-inorganic nano laminated encapsulation layer using molecular layer deposition (MLD) combined with atomic layer deposition (ALD). The $Al_2O_3$ inorganic layers as an effective single encapsulation layer were deposited at 80 degree C using ALD with alternating surface-saturation reactions of TMA and $H_2O$. A self-assembled organic layers (SAOLs) were fabricated at the same temperature using MLD. MLD and ALD deposition process were performed in the same reaction chamber. The prepared SAOL-$Al_2O_3$ organic-inorganic nano laminate films exhibited good mechanical stability and excellent encapsulation property. The measurement of water vapor transmission rate (WVTR) was performed with Ca test. We controlled thickness-ratio of organic and inorganic layer, and specific ratio showed a lowest WVTR value. Also this encapsulation layer contained very few pin-holes or defects which were linked in whole area by defect test. To apply into real OLEDs panels, we controlled a film stress from tensile to compressive and flexibility defined as an elastic modulus with organic-inorganic ratio. It has shown that OLEDs panel encapsulated with nano laminate layer exhibits better properties than single layer encapsulated in acceleration conditions. These results indicate that the organic-inorganic nano laminate thin films have high potential for flexible display applications.

• 한국의류산업학회지
• /
• 제17권5호
• /
• pp.854-861
• /
• 2015

This study evaluates the objective and subjective hand as well as the preference for hand and outdoor jackets on laminated waterproof breathable fabrics with different constituent characteristics to identify those best suited for consumer needs. Mechanical properties and objective hands were measured by the KES-FB system. The subjective hand and the preference of laminated waterproof breathable fabric for outdoor jackets were rated by the 20's and 30's women experts with tactile and visual senses that utilized a questionnaire with a seven-point semantic differential scale; subsequently, the flexibility and compressive elasticity of laminated waterproof breathable fabrics were low. However, light and thin waterproof breathable fabrics with a smooth surface had high scores in smoothness, fullness & softness and total hand value. In addition, laminated waterproof breathable fabrics were classified into three hand factors: flexibility, density, and surface properties. There were significant differences on flexibility and surface property perceptions, hand and out-door jackets preferences according to the characteristics of waterproof breathable fabrics. The hand preference of the laminated waterproof breathable fabric improved with decreasing 2HB and increasing EM. However, EM showed positive effect for outdoor jacket preferences. Those that were flexible and smooth were preferred for outdoor jackets.

• 한국세라믹학회지
• /
• 제55권6호
• /
• pp.527-555
• /
• 2018

High-temperature thermal insulation materials challenge extensive oxide candidates such as porus $SiO_2$, $Al_2O_3$, yttria-stabilized zirconia, and mullite, due to the needs of good mechanical, thermal, and chemical reliabilities at high temperatures simultaneously. Recently, porous rare earth (RE) silicates have been revealed to be excellent thermal insulators in harsh environments. These materials display attractive properties, including high porosity, moderately high compressive strength, low processing shrinkage (near-net-shaping), and very low thermal conductivity. The current critical challenge is to balance the excellent thermal insulation property (extremely high porosity) with their good mechanical properties, especially at high temperatures. Herein, we review the recent developments in processing techniques to achieve extremely high porosity and multiscale strengthening strategy, including solid solution strengthening and fiber reinforcement methods, for enhancing the mechanical properties of porous RE silicate ceramics. Highly porous RE silicates are highlighted as emerging high-temperature thermal insulators for extreme environments.

• Journal of Welding and Joining
• /
• 제11권4호
• /
• pp.91-102
• /
• 1993

The plasma sprayed $Cr_3C_2$-NiCr coatings are widely used as wear-resistant and corrosion-resistant materials. The mechanical and wear properties of the plasma sprayed $Cr_3C_2$-NiCr coating on steel plate were examined in this study. The pore in the coatings could be classified into two types, the one is the intrinsic pore originated from the spraying powder, the other is the extrinsic pore formed during spraying. During the tensile adhesion test, the fracture occured at the interface of top coating and bond coating. It is though that the compressive residual stress increases with the increase of the top coating thickness. From the wear test, it was found that the wear rate increased with the increase of the sliding velocity regardless of the temperature. It is thought that the fracture toughness reduces with the increase of the sliding velocity at $30^{\circ}C$ and that the adhesion amount increases with the increase of the sliding velocity at $400^{\circ}C$ It is concluded that the wear mechanism at $30^{\circ}C$ is the fracture and pull-out of the carbide particles due to the fatigue on sliding surface, while the wear mechanism at $400^{\circ}C$ is the adhesion of the smeared layer formed during wear process.

• Applied Biological Chemistry
• /
• 제32권4호
• /
• pp.332-337
• /
• 1989

재수화한 동결건조 즉석미반의 리올로지 성질을 통상법으로 취반한 미반과 비교하면서 조사하였다. 온도$(60{\sim}90^{\circ}C)$를 달리한 복원시간에 따른 미립 경도의 역수(연화도)는 복원온도에 상관없이 1차 반응 속도식에 따라 감소하였고, 경도반응의 속도 상수 값은 온도에 따라 증가하였으며, 이의 활성화 에너지는 6.1 kcal/g-mol이었다. 여러 온도 $(60{\sim}90^{\circ}C)$에서 복원시킨 즉석미반의 압축응력 완화 곡선은 통상법으로 취반한 미반과 마찬가지로 일반화된 Maxwell의 6요소 역학모형으로 설명되었고, 즉석미반은 취반미보다 완화되기 쉬우나 복원온도가 높을수록 탄력성이 높아지는 특성을 나타내었다.

• 한국해양공학회지
• /
• 제23권2호
• /
• pp.74-80
• /
• 2009

Surface hardening treatments, such as using the high-frequency induction hardening method, are widely used to increase the fatigue life and prevent the failure of materials by locally increasing the surface hardness. This method, in particular, brings an improvement in static strength by compressive residual surface stress due to the hardening. In this study, the mechanical properties of high-frequency induction hardened SCM440 steel were investigated. These results were also compared with those for base metal and a Q/T (tempering after quenching) treatment specimen. The test results showed that partially high-frequency induction hardened SCM440 steel specimens were more improved in static strength, surface hardness, fatigue limit, and anti-wear than the base metal and Q/T treatment specimens. In particular, the fatigue limit of the high-frequency induction hardened SCM440 steel increased by more than about 52% compared to that of base metal and by about 25% compared to that of the Q/T specimen.

• Composites Research
• /
• 제33권5호
• /
• pp.256-261
• /
• 2020

본 연구에서는 Al-Ti-C 반응계의 점화온도에 대해 고찰하고, 자전연소합성법 및 교반주조 공정을 통해 TiC/Mg 금속복합재료를 제조하여 미세조직 및 기계적 특성을 분석하였다. 0, 10, 20, 30 vol.% TiC 입자가 균일하게 분산된 Mg 복합재료를 제조하였고, 강화재의 양이 증가할수록 기지 대비 우수한 압축강도 및 내마모특성을 보였다. 이는 in-situ 자전연소합성법에 의해 결함이나 불순물 등의 오염이 적은 TiC/Mg 금속복합재료 제조로 기지에서 강화재로의 효과적인 하중 전달에 의한 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제22권5호
• /
• pp.596-606
• /
• 1998

Thermophysical properties and the compressive strength of concrete used in nuclear power plants in Korea were measured. The chemical composition of the concrete was also analyzed. The measured thermophysical properties include the density, the thermal conductivity, the thermal diffusivity and the specific heat for a wide temperature range of 20.deg. C to 1100.deg. C. The chemical composition of Korean concrete is similar to that of US basaltic concrete and the thermophysical properties are strongly temperature dependent. The density, the conductivity and the diffusivity decrease with an increase in temperature, and particularly the conductivity and the diffusivity are a 50-perdent decrease at 900.deg. C as compared with these values at room temperature. The specific heat increases until 500.deg. C, decreases from 700.deg. C to 900 .deg. C, and then increases again when temperature is above 900.deg. C. The measurement beyond 1100.deg. C is not acceptably accurate because the concrete decomposes to a liquid phase from a solid phase at that temperature. The results of this study can be applied, for example, to an analysis of the molten core-concrete interaction (MCCI) phenomenon of concrete structures at high temperature will also require those property data, especially for high temperature ranges.