• Resources Recycling
• /
• v.19 no.6
• /
• pp.93-101
• /
• 2010

In this study, we have studied hydration properties and compressive strength of the electric arc furnace reduction slag as a cement admixture. The reduction slag is mainly consisted of 17.1% of f-CaO and rapid curing clinker minerals, 37.1% of $C_{11}A_7CaF_2$, and 21.0% of $C_3A$. When the substitution rate of the slag on OPC was 30%, the initial setting time and final setting time has been shortened from 305 min. and 425 min. to 10min. and 30min. When the substitution rate of the slag on OPC was 7%, the compressive strength of mixed cement mortars has been increased than that of OPC during all period. When the substitution rate of the slag on OPC was over 20%, the compressive strength of mortars has been reduced than that of OPC at initial and final compressive strength. As a result of hydration properties of reduction slag, $C_{11}A_7CaF_2$ transfer to $C_3AH_6$ but as the substitution rate of slag on OPC increases, increased f-CaO and the metastable hydrates $C_4AH_{13}$ increased. Therefore, we should control the substitution rate of the slag on OPC was under 7% in order to use EAF reduction slag as a cement admixture.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.215-217
• /
• 2008

Crystallization behavior of the bulk metallic glass (BMG) during compression and tension was studied in the supercooled liquid region (SLR). Rod samples of the BMG alloy were produced by consolidating gas atomized powders of $Cu_{54}Zr_{22}Ti_{18}Ni_6$ using spark plasma sintering. The crystallization behavior in these samples was examined by tackling changes in thermal property during heating the samples in DSC. The present BMG alloy was firstly decomposed and then crystallized during annealing in the SLR. The phase decomposition from the original amorphous phase was retarded by the compressive stress, while it was accelerated by the tensile stress.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.1 s.15
• /
• pp.123-129
• /
• 2005

This study is as a part of the new disposal and recycling plans of heat-resource waste of Daegu dyeing industrial center we tried to examine applicable possibility of crushed thing(waste aggregate) as aggregates for mortar and concrete. To examine applicable possibility of waste aggregate as a lightweight-aggregate for concrete and mortar, we carried this study by mainly property examination of concrete according to replacement ratio of waste aggregate. We carried slump, unit weight, compressive strength and bending strength test according to replacement ratio of waste aggregate. As the result of that, if we use waste aggregate, lightweight of concrete and mortar will be possible. Specially it shows a strength improvement effect of cement hardening according to using this so it is judged that applicable possibility as aggregate for concrete and mortar is very excellent.

• Korean Journal of Materials Research
• /
• v.3 no.1
• /
• pp.58-64
• /
• 1993

The degree of work hardening in the subsurface zones varied with the experimental conditions under the rolling contact fatigue wear test of high carbon Cr-Ti alloy steel was evaluated by the distribution of residual stresses. Surface residual stresses before the test did not affect the wear property. Surface residual stresses after the test decreased by the increase of contact stress and running. velocity. but the maximum compressive residual stress and its depth of saturation in the subsurface zone increased. The relationship between these experimental results and the distribution of the theoritical shear stress was also discussed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.23-26
• /
• 2002

Ternary blended concrete containing both fly ash and granulated blast furnace slag is initial cost effective, and environment friendly. Furthermore, it has many technical advantages such as improvement of long term compressive strength, rheology property, reduction of hydration heat, etc. However, use and data on the performance of ternary blended concrete are limited, and it is necessary to study on the adoption of this technology. This study examined the durability performance of ternary blended concrete comparing with binary blended concrete and ordinary portland concrete. From the results of this study, it was concluded that ternary blended concrete is very suitable to submerged zone under maine environment.

• Advances in concrete construction
• /
• v.6 no.4
• /
• pp.375-386
• /
• 2018

This experimental work aims at developing and investigating a lightened concrete by the addition of treated straws. The used formulation is based on that of an ordinary concrete which is composed of sand and gravel as the main aggregates. The properties of the straws are improved by using one of two treatments before their use: the hot water and bitumen. Henceforth, the main objective of this study is to assess the mechanical characteristics of different formulations with different compositions and treatments on straws. The obtained results have shown that the addition of straws improves its lightness property. However, it decreases the compressive and flexural strengths as well as decreases the modulus of elasticity and increases the dimensional variations. Set into comparison to the concrete with untreated straws, the treatment of straws by hot water or by bitumen improves most of the characteristics.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.04a
• /
• pp.203-208
• /
• 1994

These tests were conducted to get a device high strength concrete products in factory using admixtures for high strength concrete. The superplasticzer was used to compensate low slump of base concrete keeping its slump up about $6\pm1cm$. To examine the property for strength revelation of concrete using admixtures for high strength concrete, steam and standard curing were compared each other. Test results show that admixtures for high strength concrete is effective in steam curing and compressive strength 500kgf/$\textrm{cm}^2$ is obtained at one day, 650kgf/$\textrm{cm}^2$ at 28days as added to concrete at the ratio of 10-15%, and 740kgf/$\textrm{cm}^2$ at the ratio of 30%. Therefore admixtures for high strength concrete is effective in steam curing and make it possible to get high strength concrete using only steam curing not using autoclave curing.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.248-251
• /
• 2005

Graphite reinforced conductive polymer composites for PEMFC bipolar plates were fabricated by the compression molding technique. Graphite powder was mixed with an phenol resin to impart electrical property in composites. In this study, conductive polymer composites with high filler $loadings(>60wt.\%)$ were manufactured to accomplish high electrical conductivity above 100S/cm. The level of compaction is important because graphite powder increase electrical conductivity of composites by direct physical contact between particles. The optimum molding pressure according to filler was proposed experimentally. Various tests(electrical conductivity, flexural strength, compressive strength, leach test, etc) were carried out to verify the performance of fabricated composites for PEMFC bipolar plates. Fabricated composites have good electrical conductivity and mechanical strength. The results of leach test and contact angle measurement showed similar characteristics compared with commercial bipolar plates.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.99-104
• /
• 2005

This study is as a part of the new disposal and recycling plans of heat-resource waste of Daegu dyeing, industrial center we tried to examine applicable possibility of crushed thing(waste aggregate) as aggregates for mortar and concrete. To examine applicable possibility of waste aggregate as a lightweight-aggregate for concrete and mortar, we carried this study by mainly property examination of concrete according to replacement ratio of waste aggregate. We carried slump, unit weight, compressive strength and bending strength test according to replacement ratio of waste aggregate. As the result of that, if we use waste aggregate, lightweight of concrete and mortar will be possible. Specially it shows a strength improvement effect of cement hardening according to using this so it is judged that applicable possibility as aggregate for concrete and mortar is very excellent.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.187-195
• /
• 2006

FDM, SLS, and EOS processes are the layered manufacturing processes far functional prototypes. In this paper, bench mark tests of those processes were carried out using various materials. The test includes mechanical properties, such as tensile and compressive strengths, hardness, impact strength, and heat resistance, and surface roughness, shape and dimensional accuracy, manufacturing time, and manufacturing costs. It is verified that SLS method is advantageous in surface roughness and manufacturing time, EOS method in shape accuracy, and FDM method is great in manufacturing costs.