• 한국산업융합학회 논문집
• /
• 제17권4호
• /
• pp.234-244
• /
• 2014

Recently it has been focused that the automobile engine has developed in a strong upward tendency for the use of the high viscosity and poorer quality fuels in achieving the high performance, fuel economy, and emission reduction. Therefore it is not easy to solve the problems between low specific fuel consumption and exhaust emission control at motor cars. In this study, it is designed and used the engine test bed which is installed with turbocharger and intercooler. In addition to equipped using CRDI by controlling injection timing with mapping modulator, it has been tested and analyzed the engine performance, combustion characteristics, and exhaust emission as operating parameters, and they were engine speeds(rpm), injection timing(bTDC), and engine load(%). From the result of an experimental analysis, peak cylinder pressure and the rate of pressure rise were increased, and the location of it was closer toward top dead center according to the increasing of engine speed and load, and with advancing injection timing. The combustion characteristics are effected by fuel injection timing due to be enhanced the mass burned fraction. Using the engine dynamometer for analyzing the engine performance, the engine torque and power have been enhanced according to advancing the fuel injection timing. In analyzing of exhaust emission, there has been a trade-off between PM and NOx with increasing of engine speed and load, and with advanced injection timing. The experimental data are shown that the formation of NOx has increased and PM, vice versa.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.273-275
• /
• 2014

An ammonia fuel system is developed and applied to both a spark ignition engine and a compression ignition engine to use ammonia as primary fuel in this study. Ammonia is injected separately into the intake manifold in liquid phase while gasoline or diesel is also injected as secondary fuel. As ammonia burns 1/6 time slower than gasoline or diesel, the spark or diesel injection timing is needed to be advanced to have better combustion phasing. The test engine showed quite high variation in the power output with large amount of ammonia. The final goal of the study is to implement a methodology to ignite ammonia-air mixture and have complete combustion without any use of the conventional fuels.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.122-128
• /
• 1999

CARS(Coherent anti-Stokes Raman Spectroscopy) temperature measurement under engine-like condition was validated by measuring unburned gas temperatures of premixed propane-air flame in a constant volume combustion chamber. The measured temperatures were compared with predictions of 2 zone flame propagation model. End-gas temperatures were measured were measured by CARS technique in a conventional 4 cylinder DOHC spark-ignition engine fueled with PRF 80. Cylinder pressure was measured simultaneously with CARS signal and used as a parameter on fitting CARS spectrum to library of theoretical spectra. There was a good agreement between the measured temperature and adiabatic core temperature calculated from measured cylinder pressure. Significant heating by pre-flame reaction in the gas was observed in the late part of compression stroke.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.231-236
• /
• 2003

HCCI(Homogeneous Charge Compression Ignition) combustion is an advanced combustion process explained as a homogeneously premixed charge of a fuel where air is admitted into the cylinder and compression ignited. It has possibility to reduce NOx by spontaneous auto-ignition at multiple points that allows very lean combustion resulting in low combustion temperatures. Particulate matters (PM) could be also reduced by the homogeneous combustion and no fuel-rich zones. Injection timing is extremely advanced to achieve homogeneous charge where a diesel fuel could not be vaporized sufficiently due to low pressure and low temperature condition. Also the over-penetration could be a severe problem. The small injection angle and multi-hole injectors were applied to solve these problems. Dimethyl ether (DME) as an altenative fuel was also applied to relive the bad vaporization problem associated with early injection of diesel fuel. Neat DME has a very high cetane rating and high vapor pressure. Contained oxygen reduces soot during the combustion. Experimental result shows DME can be easily operated in an HCCI engine. PM shows almost zero value and NOx is reduced more than 90% compared to direct-injection diesel engine operating mode but problem of early ignition needs more investigation.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.171-178
• /
• 2008

The combustion and exhaust emission characteristics were investigated in an DME fueled HCCI engine. Carbon dioxide, nitrogen and mixed gas, which was composed of carbon dioxide and nitrogen, were used as control parameters of combustion and exhaust emission. As the oxygen concentration in induction air, which was occurred by carbon dioxide, nitrogen and mixed gas, was reduced, the start of auto-ignition was retarded and the burn duration was extended due to obstruction of combustion and reduction of combustion temperature. Due to these fact, indicated mean effective pressure was increased and indicated combustion efficiency was decreased by carbon dioxide, nitrogen and mixed gas. In case of exhaust emission, hydrocarbon and carbon monoxide was increased by reduction of oxygen concentration in induction air. Especially, partial burning was appeared at lower than about 18% of oxygen concentration by supplying carbon dioxide. However it was overcome by intake air heating.

• 대한기계학회논문집B
• /
• 제35권1호
• /
• pp.75-82
• /
• 2011

디젤의 대체연료인 디메틸 에테르의 반응기구 축소에 관한 수치해석을 수행하였다. 상세반응기구(79 개의 화학종과 351 개의 반응단계)를 기초로, 최대몰농도 해석과 민감도 해석을 균질 반응기 모델에 적용하였다. 축소반응기구는 상세반응기구의 착화지연기간과 비교하여 구축하였는데, 기준값으로 $7.5{\times}10^{-5}$을 적용했을 때 44 개의 화학종과 166 개의 반응단계로 구성된다. 축소반응기구의 계산 정확도를 검증하기 위하여 두 반응기구를 단일영역 균일예혼합 압축착화 엔진모델에 적용하였고, 축소반응기구의 계산결과는 상세반응기구의 결과와 일치하였다. 따라서 본 연구의 축소반응기구는 계산의 정확도의 손실 없이 DME 를 연료로 사용하는 압축착화엔진의 착화 및 연소 과정을 모사하는데 이용될 수 있다.

• 에너지공학
• /
• 제15권3호
• /
• pp.139-145
• /
• 2006

The purpose of this study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The objective of this paper is to clarify the effects of hydrogen enrichment in LPG fuelled engine on exhaust emission, thermal efficiency and performance. The compression ratio of 8 was selected to avoid abnormal combustion. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. The relative air-fuel ratio was increased from 0.8 to 1.3, and the ignition timing was controlled to be at MBT (minimum spark advance for best torque)

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.966-969
• /
• 1998

Fast burning achieves higher efficiency, and reduces cycle variations which is able to improve vehicle driveability. Furthermore, the greater resistance to knock with fast burning can allow the fuel economy advantages associated with higher compression ratio to be realized. One way of increasing the combustion speed is to enhance the performance of ignition systems which were able to reduce the early period of combustion. It is well known that shortening the initial stage of combustion also reduces the cyclic variations. This literature survey deals with the papers which have studied the ignition process or various ignition systems. Those systems increasing the combustion speed, extending the lean misfire limit, reducing the exhaust gas and stabilizing the operating condition of the spark ignition engine by modifying the ignition process or increasing ignition energy.

• 대한기계학회논문집B
• /
• 제34권12호
• /
• pp.1043-1050
• /
• 2010

HCCI엔진에는 농도성층화와 열적성층화가 존재하고, 이것들은 착화와 연소과정에 영향을 미치고 있다. 본 연구에서는 예혼합기의 불균질성이 HCCI연소과정에 미치는 영향에 대해서 조사하였다. 우선 4행정광학엔진을 이용하여 잔류가스가 있는 경우와 급속압축장치를 이용하여 잔류가스가 없는 경우의 예혼합기의 불균질성에 대하여 비교분석하였다. DME를 연료로 이용하고 프래밍카메라를 사용하여 2차원화학발광이미지를 취득하였다. 그 결과, 잔류가스가 있는 불균질 한 경우에 4행정엔진실험에서는 연소현상이 공간적으로 연소현상의 시간차이가 발생하였다. 잔류가스가 없는 급속압축장치의 실험에서는 4행정기관의 결과에 비해서 더 적은 공간적인 변화가 존재하는 것을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제19권12호
• /
• pp.41-46
• /
• 2018

본 연구에서는 바이오가스 기반 예혼합 압축착화(Homogeneous charged compression ignition, HCCI) 엔진에 수소를 첨가하였을 때, 연소실 내부 압력, 온도 배출가스에 미치는 영향에 대해 살펴보았다. 자세히는 수소 첨가량과 과다공기량(${\lambda}$) 변화에 따른 연소실 압력 온도, 그리고 생성물로서의 NO, $CO_2$ 배출 특성을 화학 반응 해석 프로그램을 사용하여 고찰하였다. 대상의 엔진은 2300cc 바이오가스 엔진 발전기로서 압축비 13:1, 발전량 15kW 급이다. 과급압은 1.2bar 고정 조건이며, rpm은 1800rpm의 정속 조건이다. 엔진 연소 방식은 예혼합 압축 착화를 모사하였다. 본 연구를 진행하기에 앞서 바이오가스의 주요 조성인 메탄의 연소 및 산화 메커니즘에 대한 선행 연구에 대한 고찰을 통하여 연소반응 메커니즘을 규명하기 위한 반응 메커니즘 연구 기술의 경향을 살펴보고, 본 연구에 적용 가능한 반응 메커니즘을 선정하여 해석을 진행하였다. 수소를 첨가할 때 NO는 증가하는 반면, $CO_2$등의 배출량은 감소하였고 실린더 내부 압력이 상승하며, 상승 구간이 진각 됨을 알 수 있었다. 또한, 희박영역에서 수소 첨가가 가연 한계를 증가시켰다.